if (sb == NULL) { ... sb->s_error } is going to be a bad time. Return
ENOMEM when we cannot allocate an sbuf for the sysctl rather than
dereferencing the NULL pointer just returned.
Reviewed by: manu@, allanjude@
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D30373
By default, axgbe driver does a receiver reset after predefined number
of retries for the link to come up. However, this receiver reset
doesn't always suffice, due to an hardware issue.
In that case, as a workaround, a complete phy reset is necessary.
This patch introduces a sysctl that can be set to 1 to let the driver
reset the phy completely, rather than just doing receiver reset.
The workaround will be removed once the issue is fixed by means
of firmware update.
This patch also fixes the handling of the direct attach cables
properly.
Submitted by: rajesh1.kumar_amd.com
Differential Revision: https://reviews.freebsd.org/D28266
AMD 10GbE hardware is designed to have two buffers per receive descriptor to
support split header feature. For this purpose, the driver was designed to use
2 iflib freelists per receive queue. So, that buffers from 2 freelists are used
to refill an entry in the receive descriptor. The current design holds good
with regular data traffic.
But, when netmap comes into play, the current design will not fit in. The
current netmap interfaces and netmap implementation in iflib doesn't seem
to accomodate the design of 2 freelists per receive queue. So, exercising
Netmap capability with inbuilt tools like bridge, pkt-gen doesn't work with
the 2 freelists driver design.
So, the driver design is changed to accomodate the current netmap interfaces
and netmap implementation in iflib by using single freelist per receive queue
approach when Netmap capability is exercised without disturbing the current
2 freelists approach.
The dev.ax.sph_enable tunable can be set to 0 to configure the single
free list mode.
Thanks to Stephan Dewt for his Initial set of code changes for the stated
problem.
Submitted by: rajesh1.kumar_amd.com
Approved by: vmaffione
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D27797
Doing a 'dd' over iscsi will reliably cause stalls. Tx
cleaning _should_ reliably happen as data is sent.
However, currently if the transmit queue fills it will
wait until the iflib timer (hz/2) runs.
This change causes the the tx taskq thread to be run
if there are completed descriptors.
While here:
- make timer interrupt delay a sysctl
- simplify txd_db_check handling
- comment on INTR types
Background on the change:
Initially doorbell updates were minimized by only writing to the register
on every fourth packet. If txq_drain would return without writing to the
doorbell it scheduled a callout on the next tick to do the doorbell write
to ensure that the write otherwise happened "soon". At that time a sysctl
was added for users to avoid the potential added latency by simply writing
to the doorbell register on every packet. This worked perfectly well for
e1000 and ixgbe ... and appeared to work well on ixl. However, as it
turned out there was a race to this approach that would lockup the ixl MAC.
It was possible for a lower producer index to be written after a higher one.
On e1000 and ixgbe this was harmless - on ixl it was fatal. My initial
response was to add a lock around doorbell writes - fixing the problem but
adding an unacceptable amount of lock contention.
The next iteration was to use transmit interrupts to drive delayed doorbell
writes. If there were no packets in the queue all doorbell writes would be
immediate as the queue started to fill up we could delay doorbell writes
further and further. At the start of drain if we've cleaned any packets we
know we've moved the state machine along and we write the doorbell (an
obvious missing optimization was to skip that doorbell write if db_pending
is zero). This change required that tx interrupts be scheduled periodically
as opposed to just when the hardware txq was full. However, that just leads
to our next problem.
Initially dedicated msix vectors were used for both tx and rx. However, it
was often possible to use up all available vectors before we set up all the
queues we wanted. By having rx and tx share a vector for a given queue we
could halve the number of vectors used by a given configuration. The problem
here is that with this change only e1000 passed the necessary value to have
the fast interrupt drive tx when appropriate.
Reported by: mav@
Tested by: mav@
Reviewed by: gallatin@
MFC after: 1 month
Sponsored by: iXsystems
Differential Revision: https://reviews.freebsd.org/D27683
* uninitialised variable use
* Using AXGBE_SET_ADV() where it was intended; using AXGBE_ADV()
seems wrong and also causes a compiler warning.
Reviewed by: rpokala
Differential Revision: https://reviews.freebsd.org/D26839
This patch has the driver for 10Gigabit Ethernet controller in AMD
SoC. This driver is written compatible to the Iflib framework. The
existing driver is for the old version of hardware. The submitted
driver here is for the recent versions of the hardware where the Ethernet
controller is PCI-E based.
Submitted by: Rajesh Kumar <rajesh1.kumar@amd.com>
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D25793
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
we will import a newer version of the Linux code so the linuxkpi was not
used.
This is still missing 10G support, and multicast has not been tested.
Reviewed by: gnn
Obtained from: ABT Systems Ltd
Sponsored by: SoftIron Inc
Differential Revision: https://reviews.freebsd.org/D8549
