- Remove the shim interface that allowed bwn(4) to use either siba_bwn or
bhnd(4), replacing all siba_bwn calls with their bhnd(4) bus equivalents.
- Drop the legay, now-unused siba_bwn bus driver.
- Clean up bhnd(4) board flag defines referenced by bwn(4).
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13518
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Focus on code where we are doing multiplications within malloc(9). None of
these is likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
Currently, bwn(4) relies on the siba_bwn(4) bus driver to provide support
for the on-chip SSB interconnect found in Broadcom's older PCI(e) Wi-Fi
adapters. Non-PCI Wi-Fi adapters, as well as the newer BCMA interconnect
found in post-2009 Broadcom Wi-Fi hardware, are not supported by
siba_bwn(4).
The bhnd(4) bus driver (also used by the FreeBSD/MIPS Broadcom port)
provides a unified kernel interface to a superset of the hardware supported
by siba_bwn; by attaching bwn(4) via bhnd(4), we can support both modern
PCI(e) Wi-Fi devices based on the BCMA backplane interconnect, as well as
Broadcom MIPS WiSoCs that include a D11 MAC core directly attached to their
SSB or BCMA backplane.
This diff introduces opt-in bwn(4) support for bhnd(4) by providing:
- A small bwn(4) driver subclass, if_bwn_bhnd, that attaches via
bhnd(4) instead of siba_bwn(4).
- A bhndb(4)-based PCI host bridge driver, if_bwn_pci, that optionally
probes at a higher priority than the siba_bwn(4) PCI driver.
- A set of compatibility shims that perform translation of bwn(4)'s
siba_bwn function calls into their bhnd(9) API equivalents when bwn(4)
is attached via a bhnd(4) bus parent. When bwn(4) is attached via
siba_bwn(4), all siba_bwn function calls are simply passed through to
their original implementations.
To test bwn(4) with bhnd(4), place the following lines in loader.conf(5):
hw.bwn_pci.preferred="1"
if_bwn_pci_load="YES
bwn_v4_ucode_load="YES"
bwn_v4_lp_ucode_load="YES"
To verify that bwn(4) is using bhnd(4), you can check dmesg:
bwn0: <Broadcom 802.11 MAC/PHY/Radio, rev 15> ... on bhnd0
... or devinfo(8):
pcib2
pci2
bwn_pci0
bhndb0
bhnd0
bwn0
...
bwn(4)/bhnd(4) has been tested for regressions with most chipsets currently
supported by bwn(4), including:
- BCM4312
- BCM4318
- BCM4321
With minimal changes to the DMA code (not included in this commit), I was
also able to test support for newer BCMA devices by bringing up basic
working Wi-Fi on two previously unsupported, BCMA-based N-PHY chipsets:
- BCM43224
- BCM43225
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation & Plausible Labs
Differential Revision: https://reviews.freebsd.org/D13041
* Break out the 'g' phy code;
* Break out the debugging bits into a separate source file, since
some debugging prints are done in the phy code;
* Make some more chip methods in if_bwn.c public.
This brings the size of if_bwn.c down to 6,805 lines which is now
approaching managable.
This (and eventually migrating the other PHY code out) is in preparation
for adding the 11n PHY. No, the 11ac PHY (for the BCM4260 softmac part) isn't
yet open source, so we can't grow that. Yet.
This trims ~3,700 lines of code from if_bwn.c, bringing it down to a slightly
less crazy sounding 10,446 lines of code.