in some very degenerate conditions.
However, until ath_rate_form_aggr() is taught to not form aggregates
if ANY selected rate is non-MCS, this can't yet be enabled.
So, just add a comment.
* Don't treat high percentage failures as "sucessive failures" - high
MCS rates are very picky and will quite happily "fade" from low
to high failure % and back again within a few seconds. If they really
don't work, the aggregate will just plain fail.
* Only sample MCS rates +/- 3 from the current MCS. Sample will back off
quite quickly, so there's no need to sample _all_ MCS rates between
a high MCS rate and MCS0; there may be a lot of them.
* Modify the smoothing rate to be 75% rather than 95% - it's more adaptive
but it comes with a cost of being slightly less stable at times.
A per-node, hysterisis behaviour would be nicer.
This is required to support > MCS15 as more than 32 bit rate entries are
suddenly available.
This is quite messy - instead of doing typecasts at each mask operation,
this should be migrated to use a macro and have that do the typecast.
enabled.
The legacy (pre-802.11n) hardware doesn't support this - although
the AR5212 era hardware supports MRR, it doesn't have all the bits
needed to support MRR + RTS/CTS. The AR5416 and later support
a packet duration and RTS/CTS flags per rate scenario, so we should
support it.
Tested:
* AR9280, STA
PR: kern/170302
For now, the only module implement is 'sample', and that's only partially
implemented. The main issue here with reusing this structure in userland
is that it uses 'rix' everywhere, which requires the userland code to
have access to the current HAL rate table.
For now, this is a very large work in progress.
Specific details:
* The rate control information is per-node at the moment and wrapped
in a TLV, to ease parsing and backwards compatibility.
* .. but so I can be slack for now, the userland statistics are just
a copy of the kernel-land sample node state.
* However, for now use a temporary copy and change the rix entries
to dot11rate entries to make it slightly easier to eyeball.
Problems:
* The actual rate information table is unfortunately indexed by rix
and it doesn't contain a rate code. So the userland side of this
currently has no way to extract out a mapping.
TODO:
* Add a TLV payload to dump out the rate control table mapping so
'rix' can be turned into a dot11 / MCS rate.
* .. then remove the temporary copy.
the assumption that ath_softc doesn't change size based on build time
configuration.
I picked up on this because suddenly radar stuff didn't work; and
although the ath_dfs code was setting sc_dodfs=1, the main ath driver
saw sc_dodfs=0.
So for now, include opt_ath.h in driver source files. This seems like
the sane thing to do anyway.
I'll have to do a pass over the code at some later stage and turn
the radiotap TX/RX structs into malloc'ed memory, rather than in-line
inside of ath_softc. I'd rather like to keep ath_softc the same
layout regardless of configuration parameters.
Pointy hat to: adrian
been bait-and-switched from the rate control code.
This will avoid the panic that I saw and will avoid sending invalid rates
(eg 11a/11g OFDM rates when in 11b, on 11b-only NICs (AR5211)) where the
rate table is not "big".
It also will point out situations where this occurs for the 11n NICs
which will have sufficiently large rate tables that "invalid rix" doesn't
occur.
I'll try to follow this up with a commit that adds a current operating mode
check. The "rix" is only relevant to the current operating mode and rate
table.
PR: kern/165475
for Atheros AR5416 and later wireless devices.
This is a very large commit - the complete history can be
found in the user/adrian/if_ath_tx branch.
Legacy (ie, pre-AR5416) devices also use the per-software
TXQ support and (in theory) can support non-aggregation
ADDBA sessions. However, the net80211 stack doesn't currently
support this.
In summary:
TX path:
* queued frames normally go onto a per-TID, per-node queue
* some special frames (eg ADDBA control frames) are thrown
directly onto the relevant hardware queue so they can
go out before any software queued frames are queued.
* Add methods to create, suspend, resume and tear down an
aggregation session.
* Add in software retransmission of both normal and aggregate
frames.
* Add in completion handling of aggregate frames, including
parsing the block ack bitmap provided by the hardware.
* Write an aggregation function which can assemble frames into
an aggregate based on the selected rate control and channel
configuration.
* The per-TID queues are locked based on their target hardware
TX queue. This matches what ath9k/atheros does, and thus
simplified porting over some of the aggregation logic.
* When doing TX aggregation, stick the sequence number allocation
in the TX path rather than net80211 TX path, and protect it
by the TXQ lock.
Rate control:
* Delay rate control selection until the frame is about to
be queued to the hardware, so retried frames can have their
rate control choices changed. Frames with a static rate
control selection have that applied before each TX, just
to simplify the TX path (ie, not have "static" and "dynamic"
rate control special cased.)
* Teach ath_rate_sample about aggregates - both completion and
errors.
* Add an EWMA for tracking what the current "good" MCS rate is
based on failure rates.
Misc:
* Introduce a bunch of dirty hacks and workarounds so TID mapping
and net80211 frame inspection can be kept out of the net80211
layer. Because of the way this code works (and it's from Atheros
and Linux ath9k), there is a consistent, 1:1 mapping between
TID and AC. So we need to ensure that frames going to a specific
TID will _always_ end up on the right AC, and vice versa, or the
completion/locking will simply get very confused. I plan on
addressing this mess in the future.
Known issues:
* There is no BAR frame transmission just yet. A whole lot of
tidying up needs to occur before BAR frame TX can occur in the
"correct" place - ie, once the TID TX queue has been drained.
* Interface reset/purge/etc results in frames in the TX and RX
queues being removed. This creates holes in the sequence numbers
being assigned and the TX/RX AMPDU code (on either side) just
hangs.
* There's no filtered frame support at the present moment, so
stations going into power saving mode will simply have a number
of frames dropped - likely resulting in a traffic "hang".
* Raw frame TX is going to just not function with 11n aggregation.
Likely this needs to be modified to always override the sequence
number if the frame is going into an aggregation session.
However, general raw frame injection currently doesn't work in
general in net80211, so let's just ignore this for now until
this is sorted out.
* HT protection is just not implemented and won't be until the above
is sorted out. In addition, the AR5416 has issues RTS protecting
large aggregates (anything >8k), so the work around needs to be
ported and tested. Thus, this will be put on hold until the above
work is complete.
* The rate control module 'sample' is the only currently supported
module; onoe/amrr haven't been tested and have likely bit rotted
a little. I'll follow up with some commits to make them work again
for non-11n rates, but they won't be updated to handle 11n and
aggregation. If someone wishes to do so then they're welcome to
send along patches.
* .. and "sample" doesn't really do a good job of 11n TX. Specifically,
the metrics used (packet TX time and failure/success rates) isn't as
useful for 11n. It's likely that it should be extended to take into
account the aggregate throughput possible and then choose a rate
which maximises that. Ie, it may be acceptable for a higher MCS rate
with a higher failure to be used if it gives a more acceptable
throughput/latency then a lower MCS rate @ a lower error rate.
Again, patches will be gratefully accepted.
Because of this, ATH_ENABLE_11N is still not enabled by default.
Sponsored by: Hobnob, Inc.
Obtained from: Linux, Atheros
* Use 64 bit integer types for the sample rate statistics.
When TX'ing 11n aggregates, a 32 bit counter will overflow in a few
hours due to the high packet throughput.
* Create a default label of "" rather than defaulting to "Mb" - that way
if a rate hasn't yet been selected, it won't say "-1 Mb".
Sponsored by: Hobnob, Inc.
Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
the channel width is ni->ni_chw, which is set to the negotiated channel
width. ni->ni_htflags is the capability, rather than the negotiated
value.
Teach both the TX path and the sample rate module about this.
* Pull out the static rix stuff into a different function
* I know this may slightly drop performance, but check if a static
rix is needed before each packet TX.
* Whilst I'm at it, add a little extra debugging to the rate
control stuff to make it easier to follow what's going on.
determining whether to use MRR or not.
It uses the 11g protection mode when calculating 11n related stuff, rather
than checking the 11n protection mode.
Furthermore, the 11n chipsets can quite happily handle multi-rate retry w/
protection; the TX path and rate control modules need to be taught about
that.
* add dot11rate_label() which returns Mb or MCS based on legacy or HT
* use it everywhere dot11rate() is used
* in the "current selection" part at the top of the debugging output,
otuput what the rate itself is rather than the rix. The rate index
(rix) has very little meaning to normal humans who don't know how
to find the PHY settings for each of the chipsets; pointing out the
rix rate and type is likely more useful.
packet duration for the ath_rate_sample module.
This doesn't affect the packet TX at all; only how much time the
sample rate module attributes to a completed TX.
This doesn't yet take into account HT40 packet durations as the node info
(needed to know if it's a HT20 or HT40 node) isn't available everywhere
it needs to be.
This is just the bare minimum needed to teach ath_rate_sample to try
and handle MCS rates. It doesn't at all attempt to find the best
rate by any means - it doesn't know anything about the MCS rate
relations, TX aggregation or any of the much sexier 11n stuff
that's out there.
It's just enough to transmit 11n frames and handle TX completion.
It shouldn't affect legacy (11abg) behaviour.
Obtained from: rpaulo@
This removes the chipset-dependent TX DMA completion descriptor groveling.
It should now be (more) portable to other, later atheros chipsets when the
time comes.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
o eliminate private state indexed by 802.11 rate codes; use the hal's
rate tables directly to get the same info
o calculate a mask of operational rates to optimize lookups and checks
(instead of using for loops and similar)
o optimize size bin operations
o ignore rates marked as "do not use" in the hal phy tables
o fix bug that caused upshifting to break in 11g once the rate dropped
below 11Mb/s
o add more intelligent multi-rate tx schedules
o add support for 1/2 and 1/4 width channels
o add dev.ath.X.sample_stats sysctl to dump runtime statistics to the console
(needs to go up to a user app)
o export more tuning knobs via sysctls (still a couple of magic constants)
making the use of sc_hwmap to do direct mapping impractical. Switch to
indexing by the rate index instead of the rate code and adjust associated
state and logic appropriately. This has several benefits including
simplification of the led code.
o fix radiotap capture of HT rates
o fix conditional compilation of HT radiotap support to be based on the
hal having 5416 support; not the ABI version as hal builds may or may
not include 5416 support
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
framework for non-MPSAFE network protocols:
- Remove debug_mpsafenet variable, sysctl, and tunable.
- Remove NET_NEEDS_GIANT() and associate SYSINITSs used by it to force
debug.mpsafenet=0 if non-MPSAFE protocols are compiled into the kernel.
- Remove logic to automatically flag interrupt handlers as non-MPSAFE if
debug.mpsafenet is set for an INTR_TYPE_NET handler.
- Remove logic to automatically flag netisr handlers as non-MPSAFE if
debug.mpsafenet is set.
- Remove references in a few subsystems, including NFS and Cronyx drivers,
which keyed off debug_mpsafenet to determine various aspects of their own
locking behavior.
- Convert NET_LOCK_GIANT(), NET_UNLOCK_GIANT(), and NET_ASSERT_GIANT into
no-op's, as their entire behavior was determined by the value in
debug_mpsafenet.
- Alias NET_CALLOUT_MPSAFE to CALLOUT_MPSAFE.
Many remaining references to NET_.*_GIANT() and NET_CALLOUT_MPSAFE are still
present in subsystems, and will be removed in followup commits.
Reviewed by: bz, jhb
Approved by: re (kensmith)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
o no more ds_vdata in tx/rx descriptors
o split h/w tx/rx descriptor from s/w status
o as part of the descriptor split change the rate control module api
so the ath_buf is passed in to the module so it can fetch both
descriptor and status information as needed
o add some const poisoning
Also for sample rate control algorithm:
o split debug msgs (node, rate, any)
o uniformly bounds check rate indices (and in some cases correct checks)
o move array index ops to after bounds checking
o use final tsi from the status block instead of the h/w descriptor
o replace h/w descriptor struct's with proper mask+shift defs (this
doesn't belong here; everything is known by the driver and should
just be sent down so there's no h/w-specific knowledge)
MFC after: 1 month
