o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
sdhci(4), mmc(4) and mmcsd(4). For the most part, this consists of:
- Correcting and extending the infrastructure for negotiating and
enabling post-DDR52 modes already added as part of r315598. In
fact, HS400ES now should work as well but hasn't been activated
due to lack of corresponding hardware.
- Adding support executing standard SDHCI initial tuning as well
as re-tuning as required for eMMC HS200/HS400 and the fast UHS-I
SD card modes. Currently, corresponding methods are only hooked
up to the ACPI and PCI front-ends of sdhci(4), though. Moreover,
sdhci(4) won't offer any modes requiring (re-)tuning to the MMC/SD
layer in order to not break operations with other sdhci(4) front-
ends. Likewise, sdhci(4) now no longer offers modes requiring the
set_uhs_timing method introduced in r315598 to be implemented/
hooked up (previously, this method was used with DDR52 only, which
in turn is only available with Intel controllers so far, i. e. no
such limitation was necessary before). Similarly for 1.2/1.8 V VCCQ
support and the switch_vccq method.
- Addition of locking to the IOCTL half of mmcsd(4) to prevent races
with detachment and suspension, especially since it's required to
immediately switch away from RPMB partitions again after an access
to these (so re-tuning can take place anew, given that the current
eMMC specification v5.1 doesn't allow tuning commands to be issued
with a RPMB partition selected). Therefore, the existing part_mtx
lock in the mmcsd(4) softc is additionally renamed to disk_mtx in
order to denote that it only refers to the disk(9) half, likewise
for corresponding macros.
On the system where the addition of DDR52 support increased the read
throughput to ~80 MB/s (from ~45 MB/s at high speed), HS200 yields
~154 MB/s and HS400 ~187 MB/s, i. e. performance now has more than
quadrupled compared to pre-r315598.
Also, with the advent of (re-)tuning support, most infrastructure
necessary for SD card UHS-I modes up to SDR104 now is also in place.
Note, though, that the standard SDHCI way of (re-)tuning is special
in several ways, which also is why sending the actual tuning requests
to the device is part of sdhci(4). SDHCI implementations not following
the specification, MMC and non-SDHCI SD card controllers likely will
use a generic implementation in the MMC/SD layer for executing tuning,
which hasn't been written so far, though.
However, in fact this isn't a feature-only change; there are boards
based on Intel Bay Trail where DDR52 is problematic and the suggested
workaround is to use HS200 mode instead. So far exact details are
unknown, however, i. e. whether that's due to a defect in these SoCs
or on the boards.
Moreover, due to the above changes requiring to be aware of possible
MMC siblings in the fast path of mmc(4), corresponding information
now is cached in mmc_softc. As a side-effect, mmc_calculate_clock(),
mmc_delete_cards(), mmc_discover_cards() and mmc_rescan_cards() now
all are guaranteed to operate on the same set of devices as there no
longer is any use of device_get_children(9), which can fail in low
memory situations. Likewise, mmc_calculate_clock() now longer will
trigger a panic due to the latter.
o Fix a bug in the failure reporting of mmcsd_delete(); in case of an
error when the starting block of a previously stored erase request
is used (in order to be able to erase a full erase sector worth of
data), the starting block of the newly supplied bio_pblkno has to be
returned for indicating no progress. Otherwise, upper layers might
be told that a negative number of BIOs have been completed, leading
to a panic.
o Fix 2 bugs on resume:
- Things done in fork1(9) like the acquisition of an SX lock or the
sleepable memory allocation are incompatible with a MTX_DEF taken.
Thus, mmcsd_resume() must not call kproc_create(9), which in turn
uses fork1(9), with the disk_mtx (formerly part_mtx) held.
- In mmc_suspend(), the bus is powered down, which in the typical
case of a device being selected at the time of suspension, causes
the device deselection as part of the bus acquisition by mmc(4) in
mmc_scan() to fail as the bus isn't powered up again before later
in mmc_go_discovery(). Thus, power down with the bus acquired in
mmc_suspend(), which will trigger the deselection up-front.
o Fix a memory leak in mmcsd_ioctl() in case copyin(9) fails. [1]
o Fix missing variable initialization in mmc_switch_status(). [2]
o Fix R1_SWITCH_ERROR detection in mmc_switch_status(). [3]
o Handle the case of device_add_child(9) failing, for example due to
a memory shortage, gracefully in mmc(4) and sdhci(4), including not
leaking memory for the instance variables in case of mmc(4) (which
might or might not fix [4] as the latter problem has been discovered
independently).
o Handle the case of an unknown SD CSD version in mmc_decode_csd_sd()
gracefully instead of calling panic(9).
o Again, check and handle the return values of some additional function
calls in mmc(4) instead of assuming that everything went right or mark
non-fatal errors by casting the return value to void.
o Correct a typo in the Linux IOCTL compatibility; it should have been
MMC_IOC_MULTI_CMD rather than MMC_IOC_CMD_MULTI.
o Now that we are reaching ever faster speeds (more improvement in this
regard is to be expected when adding ADMA support to sdhci(4)), apply
a few micro-optimizations like predicting mmc(4) and sdhci(4) debugging
to be off or caching erase sector and maximum data sizes as well support
of block addressing in mmsd(4) (instead of doing 2 indirections on every
read/write request for determining the maximum data size for example).
Reported by: Coverity
CID: 1372612 [1], 1372624 [2], 1372594 [3], 1007069 [4]
mmc(4). For the most part, this consists of support for:
- Switching the signal voltage (VCCQ) to 1.8 V or (if supported
by the host controller) to 1.2 V,
- setting the UHS mode as appropriate in the SDHCI_HOST_CONTROL2
register,
- setting the power class in the eMMC device according to the
core supply voltage (VCC),
- using different bits for enabling a bus width of 4 and 8 bits
in the the eMMC device at DDR or higher timings respectively,
- arbitrating timings faster than high speed if there actually
are additional devices on the same MMC bus.
Given that support for DDR52 is not denoted by SDHCI capability
registers, availability of that timing is indicated by a new
quirk SDHCI_QUIRK_MMC_DDR52 and only enabled for Intel SDHCI
controllers so far. Generally, what it takes for a sdhci(4)
front-end to enable support for DDR52 is to hook up the bridge
method mmcbr_switch_vccq (which especially for 1.2 V signaling
support is chip/board specific) and the sdhci_set_uhs_timing
sdhci(4) method.
As a side-effect, this change also fixes communication with
some eMMC devices at SDR high speed mode with 52 MHz due to
the signaling voltage and UHS bits in the SDHCI controller no
longer being left in an inappropriate state.
Compared to 52 MHz at SDR high speed which typically yields
~45 MB/s with the eMMC chips tested, throughput goes up to
~80 MB/s at DDR52.
Additionally, this change already adds infrastructure and quite
some code for modes up to HS400ES and SDR104 respectively (I did
not want to add to much stuff at a time, though). Essentially,
what is still missing in order to be able to activate support
for these latter is is support for and handling of (re-)tuning.
o In sdhci(4), add two tunables hw.sdhci.quirk_clear as well as
hw.sdhci.quirk_set, which (when hooked up in the front-end)
allow to set/clear sdhci(4) quirks for debugging and testing
purposes. However, especially for SDHCI controllers on the
PCI bus which have no specific support code so far and, thus,
are picked up as generic SDHCI controllers, hw.sdhci.quirk_set
allows for setting the necessary quirks (if required).
o In mmc(4), check and handle the return values of some more
function calls instead of assuming that everything went right.
In case failures actually are not problematic, indicate that
by casting the return value to void.
Reviewed by: jmcneill
SD Simplified specification, as well as other SD and SDIO
implemenations I've examined, suggest this disclaimer may be required.
It is unclear to me exactly what the license would be for, or why it
might be required. Err on the side of caution and include this
disclaimer so anybody deploying this code can judge for themselves. I
have no further unformation about the details.
should be easily adapted to SD 2.0 (aka SDHC), SDIO, MMC and MMCplus
cards. At the present time, there's only one bridge driver for the
ARM9 based Atmel AT91RM9200.
