- implement user-initiated background drive rebuild
- implement user-initiated background consistency check
- log controller-initiated background rebuild/check operations
Try to fix the elusive "invalid log operation" bug, and panic if we do
hit this one in the hopes of getting better information.
Tidy up diagnostic messages.
Try to use disk_create/disk_destroy correctly. This isn't working
properly yet, but it's not clear whose fault that is.
robust enough to work with dhcp. Essentially the driver returns to userland
before certain commands have been completed by the card. I'm trying to
work out the best way to fix this. There are very minor functional changes,
most of this is debugging.
Rework of debugging so a bit mask is used and re-allocation around the place.
Tried to protect ray_init with a tsleep until the network has been joined. I think this is only a partial fix as we also update the mcast and promisc
values.
(MPPC) and Microsoft Point-to-Point encryption (MPPE) protocols.
Note: the MPPC part is disabled as it requires proprietary files.
Obtained from: Whistle source tree
do not have the kernel you wish to compile against in either
/usr/src/sys or /sys, then you will need to set SYSDIR to point to the
sys directory of the source tree that contians the source.
Also, minor tweaks to the load/unload targets from Bruce.
I've had this through several make worlds, as well as using it on a
daily basis for the past couple of weeks to build modules needed for
testing at Timing Solutions.
Reviewed and revised by: bde
Work sponsored by: Timing Solutions
Update the license in the rio_usb.h (now rio500_usb.h) to not be GPL.
Sorry for committing that file in the first place. The change of license
was agreed to by the original author.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
You may specify TFTP or NFS via compile time options in the loader,
but not both at this time.
Also, remove a warning about not knowing how to boot from network
devices. We can obviously do that now.
- Add support for ISA based DPT adapters (this doesn't quite work yet).
- Sync dpt_eisa.c with my local copy.
- Simplify how EISA IDs are matched.
- Prototype.
- Formatting nits.
- Conform to how I do things in dpt_pci.c/dpt_isa.c.
- Modify dpt_scsi.c:dpt_alloc() to DTRT with newbus.
- Add some comments to dpt_scsi.c:dpt_pio_get_conf().
- Add additional check to dpt_scsi.c:dpt_get_conf().
- Add some useful error messages to dpt_scsi.c:dpt_init().
request could be deallocated before the top half had finished
issuing it. The problem seems only to happen with IDE drives
and vn devices, but theoretically it could happen with any
drive. This is the most important part of a possible series
of fixes designed to remove race conditions without locking
out interrupts for longer than absolutely necessary.
Reported-by: sos
Fix-supplied-by: dillon
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
