Restructure the way ATA/ATAPI commands are processed, use a common
ata_request structure for both. This centralises the way requests
are handled so locking is much easier to handle.
The driver is now layered much more cleanly to seperate the lowlevel
HW access so it can be tailored to specific controllers without touching
the upper layers. This is needed to support some of the newer
semi-intelligent ATA controllers showing up.
The top level drivers (disk, ATAPI devices) are more or less still
the same with just corrections to use the new interface.
Pull ATA out from under Gaint now that locking can be done in a sane way.
Add support for a the National Geode SC1100. Thanks to Soekris engineering
for sponsoring a Soekris 4801 to make this support.
Fixed alot of small bugs in the chipset code for various chips now
we are around in that corner anyways.
Note: this might print failure messages on some systems, unfortunatly
the info from the device, stating if flushing is supported, cannot be trusted
so the operation is always issued on all devices, just in case...
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
Clean up the DMA interface too much unneeded stuff crept in with
the busdma code back when.
Modify the ATA_IN* / ATA_OUT* macros so that resource and offset
are gotten from a table. That allows for new chipsets that doesn't
nessesarily have things ordered the good old way. This also removes
the need for the wierd PC98 resource functions.
Tested on: i386, PC98, Alpha, Sparc64
- Use it in atacontrol(8) when listing ATA devices instead of
stopping at the first ENXIO received.
This makes atacontrol list work on my sparc64 where the two ATA
channels I have are numbered 2 and 3.
Reviewed by: sos
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
To fix scsi, don't wait for ithreads if we're dumping, it makes the
debugger sad.
To fix ata, use what appears to be a polling method if we're dumping,
I stole this from tmm but added code to ensure that this change is
only in effect while dumping.
Tested by: des
Properly handle the newer Promise SuperSwap 1000 enclosures.
Print out what kind of enclosure was found in the probe.
Misc cleanups in the enclosure handling code.
Sponsored by: Advanis Inc.
This mostly consists of functionality to serialize accesses to
the two ATA channels (which can also be used to "fix" certain
PCI based controllers).
Add support for Acard controllers.
Enable the ATA driver in PC98 GENERIC, and add device hints.
Update man page with latest support.
The PC98 core team has kindly provided me with a PC98
machine that made this all possible, thanks to all that
contributed to that effort, without that this would
probably newer have been possible..
Approved by: re@
the device is not actually present), clear the corresponding bit in
the ch->devices bitmap. This resolves a panic that occurred with ATAPI/CAM
after an APM suspend/resume, when the ATA hardware would erroneously
report an extra ATAPI device.
Approved by: re, sos
Reviewed by: roberto
MFC after: 7 days
and XPT_RESET_DEV.
In order to properly handle reset requests whether they originate in the
ATA layer (atacontrol reinit) or from the CAM layer (camcontrol reset)
ata_reinit does not cause the SIM to be deallocated anymore. The SIM
is now unconditionnally created for each ATAPI bus.
This change may cause existing bus ids to change on some setups.
Reviewed by: roberto
Approved by: sos
The CAM<>ATAPI layer was submitted by "Thomas Quinot <thomas@cuivre.fr.eu.org>"
changes form the version on the net by me (formatting, ability to be used
alone without the ATAPI native device driver, proper speed reporting...)
See /sys/conf/NOTES for usage.
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
This completes the ATA RAID support, since all functions to manipulate
the RAID are accessible from FreeBSD, the BIOS on the ATA RAID cards
are only nessesary for booting.
I decided to allow for creation of ATA RAID's on any ATA controller, but
please keep in mind the restrictions on that. Due to the BIOS not
knowing what to do you can only boot from a RAID1 or the first disk
in a SPAN, if its not located on a "real" ATA RAID controller like
the Promise or Highpoint controllers.
Sponsored by: Advanis
keep gcc-3.1+ happy:
ata-all.c:410: warning: deprecated use of label at end of compound statement
ata-all.c:587: warning: deprecated use of label at end of compound statement
ata-raid.c:99: warning: deprecated use of label at end of compound statement
ata-raid.c:151: warning: deprecated use of label at end of compound statement
Link if only ATAPI device in kernel config
Remove unused #includes
Rearrange a bit in ata-raid to make diff against -stable smaller
Enable wc as default again, dunne how this happend...
Add code to properly detach/attach disks that are part of a RAID.
Mark a disk that is attached on an ATA channel belonging to a
RAID as a spare disk that can be used for rebuilding failed RAID1's.
Add support for rebuilding failed RAID1's.
Several fixes to the detach/attach code.
For replacing a disk in a failed RAID1 do the following:
Find the controller channel# of the failed disk.
Exec 'atacontrol detach <channel#>' to free the disk from the system.
Replace the failed disk with a new one of at least the same size.
If your have your disks in drawers/enclosures this can be done with
the system still running.
Exec 'atacontrol attach <channel#>' to add the disk to the system and
mark it as a valid spare for rebuild.
Exec 'atacontrol rebuild <array#>'
The system will rebuild the array on the fly, the array can still
be used during this, although with slower performance.
Please let me know of any problems with this!
Sponsored by: Advanis Inc.
MFC after: 2 weeks
More cleanups of the RAID1 failure mode code.
Add functionality that writes the changed RAID config setup
back to the disks (in controller BIOS specific format), so
that a reboot will make the BIOS pick up the changed config.
to fix their code.
ata stuff:
Change name of ar_attach to not colide with existing ar_attach in if_ar.c.
usb stuff:
Create a dummy function to satisfy a call to it when in DEBUG mode.
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
Add tagged queueing support for new IBM drives.
Add support for Yet Another Promise ATA 100 chip.
Flush disk cache on close.
Dont flush the disk cache on BIO_ORDERED anymore.
Cleanup the tests for DMA on ATAPI devices.
Allow to share ALL irq's even the std irg 14 & 15.
Fix calculation bug in end of media code on CD's.
Add REZERO on opening a CDR/CDRW.
Cleanup ataioctl a bit.
- Callers of asleep() and await() have been converted to calling tsleep().
The only caller outside of M_ASLEEP was the ata driver, which called both
asleep() and await() with spl-raised, so there was no need for the
asleep() and await() pair. M_ASLEEP was unused.
Reviewed by: jasone, peter
see atacontrol(8) for more.
Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS
options are gone, use the tuneables listed in ata.4 instead from
the loader (this makes it possible to switch off DMA before the
driver has to touch the devices on broken hardware).
Proberly fail outstanding bio requests on devices that are detached.
This makes it possible to change between disk/cdrom/dvd/whathaveyou
in a notebook, just by suspending it, changing the device in the
bay (or what you model calls it), unsuspend and the ATA driver
will figure out what disappeared and properly fail those, and attach
any new devices found.
