up when operating in PCI-X mode. For some received packets there is
data corruption in the first few bytes in that case. Aligning the
packet buffer eliminates the corruption. With this fix, the code
that offsets the packet buffer up by 2 bytes to align the payload is
disabled for BCM5701s operating in PCI-X mode. On the i386, which
permits unaligned accesses, the payload is left unaligned. On other
platforms, the packet is copied after reception to force alignment
of the payload. Obviously, this work-around reduces performance in
those cases (BCM5701 plus PCI-X) where it is in effect.
MFC after: 3 days
sysctl (machdep.cpu_idle_hlt) to off in the SMP case. This allows you to
turn it on if you wish and do not particularly care about the small window
where a cpu will remain halted even when a job is placed on the run queue
(until the next clock tick).
obtained, when all other scheduling activity is suspended. This is needed
on sparc64 to deactivate the vmspace of the exiting process on all cpus.
Otherwise if another unrelated process gets the exact same vmspace structure
allocated to it (same address), its address space will not be activated
properly. This seems to fix some spontaneous signal 11 problems with smp
on sparc64.
otherwise we might get interrupts and are unable to
handle them properly, which results in a page fault.
PR: kern/39549
Submitted by: Gil Kloepfer <gil@arlut.utexas.edu>
Add a comment so that people don't forget to keep the
version in src/lib/libmd/md5c.c in sync with this one.
This fixes a warning on sparc64.
Reviewed by: phk
request. We need to eat the MAC address of the packet before we go
looking at the SSID and such. Doing do is sufficient to make Cisco
cards assocaite with prism II cards.
The submitter says that Linux does the same thing.
Submitted by: jhay
a small chance that it might have broken loading the miibus, so err on
the side of caution until I can figure out what is going on. This
backs out all but the PCI, PCIB and ISA bus interfaces being
"standard," which have been well tested...
Add XXX comments to mark places which need to be taken care of
if we want to remove this part of the kernel from Giant.
Add a comment on a potential performance problem with ip_forward()
easier loading of modules that might refer to these interfaces. None
of the code that implements them is standard, just the glue. This
bloats the kernel a whopping 8k.
Silence on: arch@
o ToPIC is happy with two cards now, even when the two cards are
modems.
o Fix (all?) hangs on boot when power is applied to the card. I
suspect that this will make the Ricoh bridges happier and also
make a lot of VAIO owners happy (confirm to me in private email
please :-).
o All Cardbus bridges should now support 3.3V, X.XV and Y.YV cards,
to the extent that the underlying hardware supports such cards.
(X.X and Y.Y haven't been assigned values yet :-).
o Better 3.3V support for Ricoh ISA bridges.
How:
o Don't mess with the power register when scanning the cards. It
is unnecessary and causes BADVcc conditions on many chipsets. These
in turn can cause an interrupt storm.
o Make pcic_disable reset the slot's voltage.
o Move initializing voltage for the slot until after it has been
disabled.
o Fix a lot of issues with the pcic_cardbus_power routine. We
now properly enable the card and take it out of reset after
a power change.
o When detecting the card's voltage, if we're in a BadVcc state,
direct the bridge to rescan the card for what it supports.
(we might need to in the future set the power register to 0
before doing this).
o Don't preserve CLKSTOP. need to revisit this.
o Better support for Ricoh ISA bridges for 3.3V cards.
o Don't write to PCIC_POWER directly as offten, but instead go
through the pcic_power interface.
o All cardbus bridges now default to use cardbus power control.
o Add misc register definitions.
o remove some (now) bogus comments.
Extra Special Thanks To: Scott Lamber for his kind and generous loan
of a Toshiba laptop with a ToPIC 100 in it for my use.
