The tag enforces a single restriction that all DMA transactions must not
cross a 4GB boundary. Note that while this restriction technically only
applies to PCI-express, this change applies it to all PCI devices as it
is simpler to implement that way and errs on the side of caution.
- Add a softc structure for PCI bus devices to hold the bus_dma tag and
a new pci_attach_common() routine that performs actions common to the
attach phase of all PCI bus drivers. Right now this only consists of
a bootverbose printf and the allocate of a bus_dma tag if necessary.
- Adjust all PCI bus drivers to allocate a PCI bus softc and to call
pci_attach_common() from their attach routines.
MFC after: 2 weeks
register changes when compiled with SCHIZO_DEBUG and take advantage
of them.
- Add support for the XMITS Fireplane/Safari to PCI-X bridges. I tought
I'd need this for a Sun Fire 3800, which then turned out to not being
equipped with such a bridge though. The support for these should be
complete but given that it hasn't actually been tested probing is
disabled for now.
This required a way to alter the XMITS configuration in case a PCI-X
device is found further down the device tree so the sparc64 specific
ofw_pci kobj was revived with a ofw_pci_setup_device method, which is
called by the ofw_pcibus code for every device added.
- A closer inspection of the OpenSolaris code indicates that consistent
DMA flushing/syncing as well as the block store workaround should be
applied with every BUS_DMASYNC_POSTREAD instead of in a wrapper around
interrupt handlers for devices behind PCI-PCI bridges only as suggested
by the documentation (code for the latter actually exists in OpenSolaris
but is disabled by default), which also makes more sense.
- Add a workaround for Casinni/Skyhawk combinations. Chances are that
this solves the crashes seen when using the the on-board Casinni NICs
of Sun Fire V480 equipped with centerplanes other than 501-6780 or
501-6790. This also takes advantage of the ofw_pci_setup_device method.
- Mark some unused parameters as such.
enable IDE I/O" bit which prevents data access traps with revision
0xc8 in Fire-based machines when pci(4) enables PCIM_CMD_PORTEN.
- Like for sun4v also don't add the PCI side of host-PCIe bridges to
the bus on sun4u as they don't have configuration space implement
there either.
is that the JBus to EBus bridges share the interrupt controller of a
sibling JBus to PCIe bridge (at least as far as the OFW device tree
is concerned, in reality they are part of the same chip) so we have to
probe and attach the latter first. That happens to be also the case
due to the fact that the JBus to PCIe bridges appear first in the OFW
device tree but it doesn't hurt to ensure the right order.
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.
This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.
Reviewed by: marius
Obtained from: sparc64
the latency based on the Min_Gnt register so use the algorithm found
in OpenSolaris as they probably know how to interpret the value Sun
puts into these registers (previously, the latency calculated for
66MHz was most likely wrong) and for bridges additionally set up the
secondary latency register. Also set up the bridge control register
the way it's done in OpenSolaris. As the latency register don't apply
to PCI-Express and the bridge control setup wasn't tested on sun4v
(besides most likely not being needed), expand the #ifndef SUN4V
accordingly.
MFC after: 3 days
have separate configuration spaces so by definition they implement
different PCI domains. Thus change psycho(4) to use PCI domains
instead of reenumerating all PCI busses so they have globally unique
bus numbers and drop support for reenumerating busses in the OFW PCI
code.
According to CVS history reenumeration was also required in order to
get some E450 to boot but given that no other open source kernel
changes the PCI bus numbers assigned by the firmware I believe the
real problem was that the old code used the bus number as the device
number for the PCI busses and unlike most of the other machines the
firmwares of the problematic ones don't use disjoint PCI bus numbers
across the host-PCI-bridges.
MFC after: 1 month
is required by the X.Org PCI domains code and additionally needs
a workaround for Hummingbird and Sabre bridges as these don't
allow their config headers to be read at any width, which is an
unusual behavior.
- In psycho(4) take advantage of DEFINE_CLASS_0 and use more
appropriate types for some softc members.
MFC after: 3 days
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
33MHz for calculating the latency timer values for its children.
Inspired by NetBSD doing the same and Linux as well as OpenSolaris
using a similar approach.
While at it rename a variable and change its type to be more
appropriate fuer values of PCI properties so the variable can be
more easily reused.
- Initialize the cache line size register of PCI devices to a
legal value; the cache line size is limited to 64 bytes by the
Fireplane/Safari, JBus and UPA interconnection busses. Setting
it to an unsupported value caused bad performance at least with
GEM as it causes them to not do cache line bursts and to not
issue cache line commands on the PCI bus.
Approved by: re (kensmith)
MFC after: 1 week
iommureg.h (which already began to bitrot) and iommuvar.h from the
sun4v source and adjust some of the source which is shared between
sparc64 and sun4v as appropriate.
firmware (mainly 'pmu' and its 'lomp' dupe found in a couple of
later USII{e,i}-based machines) by checking whether a device with
the same triple of bus number, slot and function already has been
added. This is the simple yet effective approach introduced in
OpenBSD some time ago, but which has the flaw that it assumes
that the device and its dupe(s) found in the OFW device tree are
equal or at least the one encountered first is in some way the
more important one (this is the case with 'pmu' and 'lomp'; the
'pmu' node has couple of properties and children while the 'lomp'
one misses most of these). If there's ever a device/dupe pair
where we don't encounter the more important node first, we'll
probably need to introduce a quirk list in order to add the
desired device but prevent its dupe(s) from being added.
MFC after: 1 week
to search for a specific extended capability. If the specified capability
is found for the given device, then the function returns success and
optionally returns the offset of that capability. If the capability is
not found, the function returns an error.
ofw_bus_gen_get_*() for providing the ofw_bus KOBJ interface in order
to reduce code duplication.
- While here sync the various sparc64 bus drivers a bit (handle failure
to attach a child gracefully instead of panicing, move the printing
of child resources common to bus_print_child() and bus_probe_nomatch()
implementations of a bus into a <bus>_print_res() function, ...) and
fix some minor bugs and nits (plug memory leaks present when attaching
a bus or child device fails, remove unused struct members, ...).
Additional testing by: kris (central(4) and fhc(4))
bridge in the device tree which lacks the mandatory (also by the OFW PCI
bus binding spec) "reg" property. Change the code to just ignore nodes
missing the "reg" property instead of panicing when encountering such a
node. Also ignore nodes without a "name" property (guaranteed by the OFW
PCI bus binding spec). This brings the behaviour of the MD OFW PCI code
regarding such incomplete nodes in line with the EBus and the SBus code.
Tested by: Cyril Tikhomiroff <tikho@anor.net>
MFC after: 1 month
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.
The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
so unit numbers should match what's printed on the box more
closely.
- Real interrupt routing is implemented now, so cardbus bridges
etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
sufficient) heuristics.
- Much cleaner code.
There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.
A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.
In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
generic PCI bus driver, but uses the firmware for enumeration,
performs additional initialization for devices and firmware-specific
interrupt routing. It also implements an OFW-specific method to allow
child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
of the generic PCI-PCI bridge driver; it has it's own method for
interrupt routing, as well as some sparc64-specific methods (one to
get the node again, and one to adjust the bridge bus range, since
we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
drivers above.
- Provide a small common framework for interrupt routing (for all
bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
bunch of old kludges in pci_read_config(), and the whole
preinitialization (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
required for PCI), and move it to a more correct location (new
support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.
In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.
Reviewed in part by: imp
Tested by: jake, Marius Strobl <marius@alchemy.franken.de>,
Sergey Mokryshev <mokr@mokr.net>,
Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by: kris
