If power exceed the slot limit, or slot limit is unknown the ConnectX-6
firmware will shutdown its port.
Inform the user via debug message.
MFC after: 3 days
Approved by: hselasky (mentor), kib (mentor)
Sponsored by: Mellanox Technologies
The receive side scaling stride parameter is a value which define the interval
between active receive side queues. The traffic for the inactive queues is
redirected to the nearest active queue by use of modulus. The default value
of this parameter is one, which means all receive side queues are used.
The point of this feature is to redirect more traffic to fewer receive side
queues in order to take more advantage of sorted large receive offload,
sorted LRO. The sorted LRO works better when more packets are accumulated
per service interval.
MFC after: 3 days
Approved by: re (marius)
Sponsored by: Mellanox Technologies
Inspecting the PRM no more than 0x3F data segments, DS, of size 16 bytes is
allowed.
Worst case scenario summary of DS usage:
Header is fixed: 2 DS
Maximum inlining: 98 => (98 - 2) / 16 = 6 DS
Remainder: 0x3F - 2 - 6 = 55 DS (mbuf frags)
Previously a value of 56 DS was used and this would work in the
normal case because not all inline data area was used up.
MFC after: 3 days
Approved by: re (marius)
Sponsored by: Mellanox Technologies
Query the minimal inline mode supported by the card.
When creating a send queue, cache the queried mode and optimize the transmit
if no inlining is required. In this case, we can avoid touching the headers
cache line and avoid dirtying several more lines by copying headers into
the send WQEs. Also, if no inline headers are used, hardware assists in
the VLAN tag framing.
Submitted by: kib@, slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
For setups having a large amount of PCI devices, it makes sense to limit the
number of MSIX vectors per PCI device, in order to avoid running out of IRQ
vectors.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The scatter list is formed by the chunks of MCLBYTES each, and larger
than default packets are returned to the stack as the mbuf chain.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
To access the data, set sysctl dev.mce.N.conf.debug_stats to 1.
This enables the sysctl node dev.mce.N.hw_ctx_debug. Its content is
the mapping of each channel' number to used receive queue and associated
completion queue, set of the transmit queues numbers and corresponding
completion queues.
Trimmed example output:
channel 30 rq 188 cq 1085
channel 30 tc 0 sq 187 cq 1084
channel 31 rq 191 cq 1087
channel 31 tc 0 sq 190 cq 1086
MFC after: 1 week
Sponsored by: Mellanox Technologies
Device detach and setting error state may deadlock over the interface mutex
like this:
a) Detach code in mlx5en waits until error state is set while the interface
mutex is locked.
b) The set error handler needs to lock the interface mutex before it can
set the error state.
The solution is to use atomics to set the error state.
MFC after: 1 week
Sponsored by: Mellanox Technologies
When resetting mlx5core instances it can happen that the order of attach and
detach for mlx5ib instances is changed. Take the unit number for mlx5_%d from
the parent PCI device, similarly to what is done in mlx5en(4), so that there
is a direct relationship between mce<N> and mlx5_<N>.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The DSCP feature is controlled using a set of sysctl(8) fields under
the qos sysctl directory entry for mlx5en(4).
For Routable RoCE QPs, the DSCP should be set in the QP's address path.
The DSCP's value is derived from the traffic class.
Linux commit:
ed88451e1f2d400fd6a743d0a481631cf9f97550
MFC after: 1 week
Sponsored by: Mellanox Technologies
When receiving a PCP change all GID entries are reloaded.
This ensures the relevant GID entries use prio tagging,
by setting VLAN present and VLAN ID to zero.
The priority for prio tagged traffic is set using the regular
rdma_set_service_type() function.
Fake the real network device to have a VLAN ID of zero
when prio tagging is enabled. This is logic is hidden inside
the rdma_vlan_dev_vlan_id() function which must always be used
to retrieve the VLAN ID throughout all of ibcore and the
infiniband network drivers.
The VLAN presence information then propagates through all
of ibcore and so incoming connections will have the VLAN
bit set. The incoming VLAN ID is then checked against the
return value of rdma_vlan_dev_vlan_id().
MFC after: 1 week
Sponsored by: Mellanox Technologies
The hardware rate limiting feature is enabled by the RATELIMIT kernel
option. Please refer to ifconfig(8) and the txrtlmt option and the
SO_MAX_PACING_RATE set socket option for more information. This
feature is compatible with hardware transmit send offload, TSO.
A set of sysctl(8) knobs under dev.mce.<N>.rate_limit are provided to
setup the ratelimit table and also to fine tune various rate limit
related parameters.
Sponsored by: Mellanox Technologies
According to the 802.1Q-2014 9.6 VLAN Tag Control Information, VID value 0
means that there is no VLAN tag assigned to the packet, and only PCP and
DEI values from the tag are meaningful. Current flow table programming
filter out such packets.
When programming VLAN filter for flow table, unconditionally add rule which
accept packets with VLAN id 0. The packets are already handled correctly
by the network stack.
Reviewed by: hselasky, slavash
Sponsored by: Mellanox Technologies
MFC after: 1 week
Make sure the command completion handler is not called when the device is
in internal error state. This can easily trigger use after free situations.
MFC after: 3 days
Sponsored by: Mellanox Technologies
During health care IRQ resources will be reallocated.
Newbus requires that Giant is locked before accessing
these resources.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Firmware dump collecting should be triggered in case firmware syndrome
with request for reset bit is set.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
- Move the semaphore locking and unlocking to the same function.
- Flags are no longer needed if the reset and crdump will be done in the
same function.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
- Move firmware dump prep and cleanup to init_one() and remove_one() so that
the init and cleanup will happen only upon driver reload.
- Add some prints to indicate firmware dump.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
The old code checked for MLX5_CR_SPACE_DOMAIN which is irrelevant here.
However, if dev->vsec_addr would be 0, an access to wrong offset would
happen.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
This fixes 32-bit compat (no ioctl command defintions are required
as struct ifreq is the same size). This is believed to be sufficent to
fully support ifconfig on 32-bit systems.
Reviewed by: kib
Obtained from: CheriBSD
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14900
error state.
If the device is in internal error state the hardware will not
generate completions. Just move on to destroy the resources.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Change page cleanup flow when in internal error to properly decrement
the page counts when reclaiming pages. That prevents timing out
waiting for extra pages that were actually cleaned up previously.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When a PCI error is detected the PCI state could be corrupt, don't
save it in that flow. Save the state after initialization. After
restoring the PCI state during slot reset save it again, restoring
the state destroys the previously saved state info.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Since the FW can be shared between PCI functions it is common that
more than one health poll will detected a failure, this can lead to
multiple resets.
The solution is to use a FW locking mechanism using semaphore space to
provide a way to synchronize between functions. The FW semaphore is
acquired via config cycle access. First the VSEC gateway must be
acquired, then the semaphore can be locked by writing a value to it
and confirmed it's locked by reading the same value back. The process
in the same to free the semaphore, except the value written should be
zero.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
If a FW assert is considered fatal, indicated by a new bit in the
health buffer, reset the FW. After the reset, follow the normal
recovery flow.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Some mlx5 adapter firmware allows the driver to reset the firmware in
the event of an error. When a software reset is issued on any physical
function all PFs enter reset state. This is a recoverable condition.
The existing recovery flow was designed to allow the recovery of a
VF after a PF driver reload. This patch expands the scope of that
flow to recover PFs or VFs after a SW reset has been issued.
When a software reset is issued the following occurs:
1. The NIC interface mode is set to SW_RESET (7) while the reset is in
progress.
2. Once the reset completes the NIC interface mode is set to NIC
disabled (1).
After the reset has been issued (added in a subsequent patch) the
health poll for other functions will detect that the NIC interface
state has been set to disabled. This will cause it to enter the
existing recovery flow. If the PCI is still working (meaning it
doesn't return 0xff on all reads) it means recovery can proceed
immediately instead of waiting 60 seconds.
The error detetion has also been refactored to avoid incorrect or
misleading log messages.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When mlx5_enter_error_state() operation is forced by shutdown, the
messages surrounding setting the error state are not informational
and confuse users.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
- 8812c24d28f4972c4f2b9998bf30b1f2a1b62adf
net/mlx5: Add fast unload support in shutdown flow
- 59211bd3b6329c3e5f4a90ac3d7f87ffa7867073
net/mlx5: Split the load/unload flow into hardware and software flows
- 4525abeaae54560254a1bb8970b3d4c225d32ef4
net/mlx5: Expose command polling interface
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
- 04c0c1ab38e95105d950db5b84e727637e149ce7
net/mlx5: PCI error recovery health care simulation
- 0179720d6be2096b8d0a4d143254ff9e77747daa
net/mlx5: Introduce trigger_health_work function
- 3fece5d676939f42f434c63dfe1bd42d7d94e6f0
net/mlx5: Continue health polling until it is explicitly stopped
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
