cards supported by cxgbe(4).
On the host side this driver interfaces with the storage stack via the
ICL (iSCSI Common Layer) in the kernel. On the wire the traffic is
standard iSCSI (SCSI over TCP as per RFC 3720/7143 etc.) that
interoperates with all other standards compliant implementations. The
driver is layered on top of the TOE driver (t4_tom) and promotes
connections being handled by t4_tom to iSCSI ULP (Upper Layer Protocol)
mode. Hardware assistance in this mode includes:
- Full TCP processing.
- iSCSI PDU identification and recovery within the TCP stream.
- Header and/or data digest insertion (tx) and verification (rx).
- Zero copy (both tx and rx).
Man page will follow in a separate commit in a couple of weeks.
Relnotes: Yes
Sponsored by: Chelsio Communications
The mdio driver interface is generally useful for devices that require
MDIO without the full MII bus interface. This lifts the driver/interface
out of etherswitch(4), and adds a mdio(4) man page.
Submitted by: Landon Fuller <landon@landonf.org>
Differential Revision: https://reviews.freebsd.org/D4606
Add support for two new devices: X552 SFP+ 10 GbE, and the single port
version of X550T.
Submitted by: erj
Reviewed by: gnn
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D4186
to do is to clean up the timer handling using the async-drain.
Other optimizations may be coming to go with this. Whats here
will allow differnet tcp implementations (one included).
Reviewed by: jtl, hiren, transports
Sponsored by: Netflix Inc.
Differential Revision: D4055
include the following list of changes:
- Added eswitch ACL table management
Introduce API for managing ACL table.
This API include the following features:
1) vlan filter - for VST/VGT+ support.
2) spoofcheck.
3) robust functionality to allow/drop general untagged/tagged traffic.
4) support for both ingress and egress ACL types.
- Added loopback filter to the vacl table.
- Added multicast list set in the vPort context
- Added promiscuous mode set in the vPort context
- Set the vlan list in vPort context
1) Check caps if VLAN list is not longer than FW supports
2) Set MODIFY_NIC_VPORT_CONTEXT command
- Changed MLX5_EEPROM_MAX_BYTES from 48 to 32 so that a single EEPROM
reading cannot cross the 128-byte boundary. Previously reading the
MCIA register was done in batches of 48 bytes. The third reading
would then by-pass the 127th byte, which means that part of the low
page and part of the high page would be read at the same time, which
created a bug:
1st: 0-47 bytes
2nd: 48-95 bytes
3rd: 96-143 bytes
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4411
driver. This includes binding all interrupt and worker threads
according to the RSS configuration, setting up correct Toeplitz
hashing keys as given by RSS and setting the correct mbuf
hashtype for all received traffic.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4410
vtophys() when loading mbufs for transmission and reception. While at
it all pointer arithmetic and cast qualifier issues were fixed, mostly
related to transmission and reception.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4284
IPv4/IPv6 checksum offloading and VLAN tag insertion/stripping.
Since uether doesn't provide a way to announce driver specific offload
capabilities to upper stack, checksum offloading support needs more work
and will be done in the future.
Special thanks to Hayes Wang from RealTek who gave input.
Use hhook(9) framework to achieve ability of loading and unloading
if_enc(4) kernel module. INET and INET6 code on initialization registers
two helper hooks points in the kernel. if_enc(4) module uses these helper
hook points and registers its hooks. IPSEC code uses these hhook points
to call helper hooks implemented in if_enc(4).
This should be a big no-op pass; and reduces the size of if_ath.c.
I'm hopefully soon going to take a whack at the USB support for ath(4)
and this'll require some reuse of the busdma memory code.
Hacks to enable target mode there complicated code, while didn't really
work. And for outdated hardware fixing it is not really interesting.
Initiator mode tested with Qlogic 1080 adapter is still working fine.
default and add a manual page for mlx5en. The mlx5 module contains
shared code for both infiniband and ethernet. The mlx5en module
contains specific code for ethernet functionality only. A mlx5ib
module is in the works for infiniband support.
Supported hardware:
- ConnectX-4: 10/20/25/40/50/56/100Gb/s speeds.
- ConnectX-4 LX: 10/25/40/50Gb/s speeds (low power consumption)
Refer to the mlx5en(4) manual page for a comprehensive list.
The team porting the mlx5 driver(s) to FreeBSD:
- Hans Petter Selasky <hselasky@freebsd.org>
- Oded Shanoon <odeds@mellanox.com>
- Meny Yossefi <menyy@mellanox.com>
- Shany Michaely <shanim@mellanox.com>
- Shahar Klein <shahark@mellanox.com>
- Daria Genzel <dariaz@mellanox.com>
- Mark Bloch <markb@mellanox.com>
Differential Revision: https://reviews.freebsd.org/D4163
Submitted by: Mark Block <markb@mellanox.com>
Sponsored by: Mellanox Technologies
Reviewed by: gnn @
MFC after: 3 days
work with the upcoming async-drain functionality. Tests can be added
to the tests directory and then the framework can be used to launch
those tests.
MFC after: 1 month
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D1755
from Mellanox Technologies. The current driver supports ethernet
speeds up to and including 100 GBit/s. Infiniband support will be
done later.
The code added is not compiled by default, which will be done by a
separate commit.
Sponsored by: Mellanox Technologies
MFC after: 2 weeks
- Move all files related to the LinuxKPI into sys/compat/linuxkpi and
its subfolders.
- Update sys/conf/files and some Makefiles to use new file locations.
- Added description of COMPAT_LINUXKPI to sys/conf/NOTES which in turn
adds the LinuxKPI to all LINT builds.
- The LinuxKPI can be added to the kernel by setting the
COMPAT_LINUXKPI option. The OFED kernel option no longer builds the
LinuxKPI into the kernel. This was done to keep the build rules for
the LinuxKPI in sys/conf/files simple.
- Extend the LinuxKPI module to include support for USB by moving the
Linux USB compat from usb.ko to linuxkpi.ko.
- Bump the FreeBSD_version.
- A universe kernel build has been done.
Reviewed by: np @ (cxgb and cxgbe related changes only)
Sponsored by: Mellanox Technologies
These are not target-specific modules, so the logic to build them should
be common. This also enables them for arm64.
Sponsored by: The FreeBSD Foundation
linux_syscallnames[] from linux_* to linux32_* to avoid conflicts with
linux64.ko. While here, add support for linux64 binaries to systrace.
- Update NOPROTO entries in amd64/linux/syscalls.master to match the
main table to fix systrace build.
- Add a special case for union l_semun arguments to the systrace
generation.
- The systrace_linux32 module now only builds the systrace_linux32.ko.
module on amd64.
- Add a new systrace_linux module that builds on both i386 and amd64.
For i386 it builds the existing systrace_linux.ko. For amd64 it
builds a systrace_linux.ko for 64-bit binaries.
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D3954
It turns out that it is pretty easy to make CloudABI work on ARM64. We
essentially only need to copy over the sysvec from AMD64 and ensure that
we use ARM64 specific registers.
As there is an overlap between function argument and return registers,
we do need to extend cloudabi64_schedtail() to only set its values if
we're actually forking. Not when we're creating a new thread.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3917
In order to make it easier to support CloudABI on ARM64, move out all of
the bits from the AMD64 cloudabi_sysvec.c into a new file
cloudabi_module.c that would otherwise remain identical. This reduces
the AMD64 specific code to just ~160 lines.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3974
MACHINE_CPUARCH expands to aarch64 for arm64, whereas MACHINE always
corresponds to the directory name under sys/ that contains the sources
for that architecture.
Atheros.
Thanks to OpenBSD for providing a driver based on the original
Atheros open source driver circa 2008. This uses the early, pre-carl9170
atheros provided firmware.
It only supports 11bg at the moment. I've not tested it with 11a
(and so the TX rate control logic may be slightly wrong!) so if
you do have the dual-band version of this hardware please do let me know.
Tested:
* AR9170, TP-Link WN821N 2GHz.
TODO:
* Hook this up to a non-module build.
CTL HA functionality was originally implemented by Copan many years ago,
but large part of the sources was never published. This change includes
clean room implementation of the missing code and fixes for many bugs.
This code supports dual-node HA with ALUA in four modes:
- Active/Unavailable without interlink between nodes;
- Active/Standby with second node handling only basic LUN discovery and
reservation, synchronizing with the first node through the interlink;
- Active/Active with both nodes processing commands and accessing the
backing storage, synchronizing with the first node through the interlink;
- Active/Active with second node working as proxy, transfering all
commands to the first node for execution through the interlink.
Unlike original Copan's implementation, depending on specific hardware,
this code uses simple custom TCP-based protocol for interlink. It has
no authentication, so it should never be enabled on public interfaces.
The code may still need some polishing, but generally it is functional.
Relnotes: yes
Sponsored by: iXsystems, Inc.
