addressed to the interface on the other side of the box follow their
historical path.
Explicitly block packets sent to the loopback network sent from the outside,
which is consistent with the behavior of the forwarding path between
interfaces as implemented in in_canforward().
Always check the arrival interface when matching the packet destination
against the interface broadcast addresses. This bug allowed TCP
connections to be made to the broadcast address of an interface on the
far side of the system because the M_BCAST flag was not set because the
packet was unicast to the interface on the near side. This was broken
when the directed broadcast code was removed from revision 1.32. If
the directed broadcast code was stil present, the destination would not
have been recognized as local until the packet was forwarded to the output
interface and ether_output() looped a copy back to ip_input() with
M_BCAST set and the receive interface set to the output interface.
Optimize the order of the tests.
Reviewed by: jlemon
related code from aio_read() and aio_write(). This field was
intended, but never used, to allow a mythical user-level library to
make an aio_read() or aio_write() behave like an ordinary read() or
write(), i.e., a blocking I/O operation.
user space. It has already been copied in and mp->mnt_stat.f_mntonname has
already been initialised by the caller.
This fixes a panic on the alpha caused by the fact that the variable
'size' wasn't initialised because the call to copyinstr() bailed out with
an EFAULT error.
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
`infrastructure' built with INVARIANT_SUPPORT for kern_mutex.c essentially
involves _mtx_assert(), which makes use of constants that were defined
under #ifdef INVARIANTS here.
This is a pretty invasive change, but there are three good
reasons to do this:
1. We'll never have > 16 bits of handle.
2. We can (eventually) enable the RIO (Reduced Interrupt Operation)
bits which return multiple completing 16 bit handles in mailbox
registers.
3. The !)$*)$*~)@$*~)$* Qlogic target mode for parallel SCSI spec
changed such that at_reserved (which was 32 bits) was split into
two pieces- and one of which was a 16 bit handle id that functions
like the at_rxid for Fibre Channel (a tag for the f/w to correlate
CTIOs with a particular command). Since we had to muck with that
and this changed the whole handler architecture, we might as well...
Propagate new at_handle on through int ct_fwhandle. Follow
implications of changing to 16 bit handles.
These above changes at least get Qlogic 1040 cards working in target
mode again. 1080/12160 cards don't work yet.
In isp.c:
Prepare for doing all loop management in outer layers.
with egcs-1.1.1. bus_space_write_multi_2() had an extra operation that
should have been removed.
Remove it.
This fixes the panic when bus_space_write_multi_2() is used.
Obtained from: jake
- Add a KASSERT() to ensure an ithread has a backing kernel thread when we
schedule it.
- Don't attempt to preemptively switch to an ithread if p_stat of curproc
is not SRUN.
newbus in revision 1.19. As a result, lnc was, I believe, broken
for all PCI cards. The softc fields `lnc_btag' and `lnc_bhandle'
were not initialised, `rap', `rdp' and `bdp' were initialised to
the wrong values, and the size of the DMA ring memory was calculated
incorrectly.
Paul Richards has further cleanups in the pipeline, but this at
least is enough to make the driver usable with VMware.
Approved by: paul
is to return EINPROGRESS, EALREADY, (so_error ONCE), EISCONN. Certain
linux applications rely on the so_error (normally 0) being returned in
order to operate properly.
Tested by: Thomas Moestl <tmoestl@gmx.net>
An initial tidyup of the mount() syscall and VFS mount code.
This code replaces the earlier work done by jlemon in an attempt to
make linux_mount() work.
* the guts of the mount work has been moved into vfs_mount().
* move `type', `path' and `flags' from being userland variables into being
kernel variables in vfs_mount(). `data' remains a pointer into
userspace.
* Attempt to verify the `type' and `path' strings passed to vfs_mount()
aren't too long.
* rework mount() and linux_mount() to take the userland parameters
(besides data, as mentioned) and pass kernel variables to vfs_mount().
(linux_mount() already did this, I've just tidied it up a little more.)
* remove the copyin*() stuff for `path'. `data' still requires copyin*()
since its a pointer into userland.
* set `mount->mnt_statf_mntonname' in vfs_mount() rather than in each
filesystem. This variable is generally initialised with `path', and
each filesystem can override it if they want to.
* NOTE: f_mntonname is intiailised with "/" in the case of a root mount.
of memory, rather than from the start.
This fixes problems allocating bouncebuffers on alphas where there is only
1 chunk of memory (unlike PCs where there is generally at least one small
chunk and a large chunk). Having 1 chunk had been fatal, because these
structures take over 13MB on a machine with 1GB of ram. This doesn't leave
much room for other structures and bounce buffers if they're at the front.
Reviewed by: dfr, anderson@cs.duke.edu, silence on -arch
Tested by: Yoriaki FUJIMORI <fujimori@grafin.fujimori.cache.waseda.ac.jp>
for selecting unit). Instead, use the resource hints mechanism.
One unfortunate situation here is that there is no resource_quad_value
function- which is what I needed for WWN boot time replacement. Worse-
you can't store the hint as just plain
hint.isp.0.nodewwn="0x50000000aaaa0001"
because this gets interpreted as an int- incorrectly because it can't
be converted to an int. I can't even get this as a string. To work
around this particular case for nodewwn && portwwn setting, this
rather grotesque form will be used:
hint.isp.0.nodewwn="w50000000aaaa0001"
hint.isp.0.portwwn="w50000000aaaa0002"
At the same time, if we have no hinted WWN, set the default WWN (which, btw,
gets overridden if the card has valid NVRAM, which is usual) to
0x400000007F000009ull (which translates to NAA == IPv4, 127.0.0.9).
Eliminate more printf's and replace them either with device_printf or
isp_prt calls.
ones where we have a CAM path) and replacing them with calls to isp_prt.,
Eliminate isp_unit references- we no longer have an isp_unit- we now
have an isp_dev that device_get_unit can work with.
`rootvnode' pointer, but vfs_syscalls.c's checkdirs() assumed that
it did. This bug reliably caused a panic at reboot time if any
filesystem had been mounted directly over /.
The checkdirs() function is called at mount time to find any process
fd_cdir or fd_rdir pointers referencing the covered mountpoint
vnode. It transfers these to point at the root of the new filesystem.
However, this process was not reversed at unmount time, so processes
with a cwd/root at a mount point would unexpectedly lose their
cwd/root following a mount-unmount cycle at that mountpoint.
This change should fix both of the above issues. Start_init() now
holds an extra vnode reference corresponding to `rootvnode', and
dounmount() releases this reference when the root filesystem is
unmounted just before reboot. Dounmount() now undoes the actions
taken by checkdirs() at mount time; any process cdir/rdir pointers
that reference the root vnode of the unmounted filesystem are
transferred to the now-uncovered vnode.
Reviewed by: bde, phk
a regular basis. Adjust our linux emulation to conform. This will
cause more dirty pages to be left for the pagedaemon to deal with,
but our new low-memory handling code can deal with it. The linux
way appears to be a trend, and we may very well make MAP_NOSYNC the
default for FreeBSD as well (once we have reasonable sequential
write-behind heuristics for random faults).
(will be MFC'd prior to 4.3 freeze)
Suggested by: Andrew Gallatin
make sure that PG_NOSYNC is properly set. Previously we only set it
for a write-fault, but this can occur on a read-fault too.
(will be MFCd prior to 4.3 freeze)
hit on the client side and prevent the server side from retiring writes.
Pipeline operations turned off for all READs (no big loss since reads are
usually synchronous) and for NFS writes, and left on for the default bwrite().
(MFC expected prior to 4.3 freeze)
Testing by: mjacob, dillon
update native priority, it is diffcult to get right and likely
to end up horribly wrong. Use an honestly wrong fixed value
that seems to work; PUSER for user threads, and the interrupt
priority for ithreads. Set it once when the process is created
and forget about it.
Suggested by: bde
Pointy hat: me
if an arriving packet belongs to us, also check that the packet arrived
through the correct interface. Skip this check if the packet was locally
generated.
CVSrepo deletion of the previous attempt will be requested:
--original message--
Add the 'virtual nulmodem driver'
Particularly useful for debuging kernels using vmware.
If your name is Bruce evans and you are a WIZ at tty interfaces,
then you should probably rip this to shreds and offer lots of suggestions and
patches. I've been using this since 4.0-CURRENT and it's never caused
problems but I'm sure I got something wrong. This is similar to the pty/cty
device driver except that both sides are ttys. Even minor numbers
are side A and odd minor numbers are side B.
Work needs to be done regarding what happens to the other side when you
close a node.
to use with vmware, configure vmware to redirect COM2 out to side A of one
of these and boot a kernel with teh gdb remote port set to sio1.
AFTER dropping into the gdb kernel debugger in your test kernel,
fire up gdb with it's remote port pointing at the appropriate side B.
To catch all console output, you can boot the vmware kernel with a serial
console, (COM1) similarly redirected to a nulmodem, and use 'tip' to observe it.
This is practically unaltered since pre 4.0 days except for
changes made along the way needed to make it compile, so any suggestions
or offers of total rewrites will be listenned to :-)
When we recieve a fragmented TCP packet (other than the first) we can't
extract header information (we don't have state to reference). In a rather
unelegant fashion we just move on and assume a non-match.
Recent additions to the TCP header-specific section of the code neglected
to add the logic to the fragment code so in those cases the match was
assumed to be positive and those parts of the rule (which should have
resulted in a non-match/continue) were instead skipped (which means
the processing of the rule continued even though it had already not
matched).
Fault can be spread out over Rich Steenbergen (tcpoptions) and myself
(tcp{seq,ack,win}).
rwatson sent me a patch that got me thinking about this whole situation
(but what I'm committing / this description is mine so don't blame him).
rather than in silly places like "VFS Cluster debugging". People
should really be using COMPAT_LINUX instead of the linux module on
dynamic systems like -current.
process's priority go through the roof when it released a (contested)
mutex. Only set the native priority in mtx_lock if hasn't already
been set.
Reviewed by: jhb
in VMware reports 0x00000000 in the PCI subsystem ID register, but
0x10001000 when you read the mirror registers in I/O space. This causes
pcn_probe() to think it's found a card in 32-bit mode, and performing
a 32-bit I/O access makes on a 16-bit port makes VMware go boom. Special
case the 0x10001000 value until somebody at VMware grows a clue.
Finally discovered by: Andrew Gallatin
For TCP, verify that the sequence number in the ICMP packet falls within
the tcp receive window before performing any actions indicated by the
icmp packet.
Clean up some layering violations (access to tcp internals from in_pcb)
handle read and write requests for widths of multiple bytes. This
can be used to read 16-bit battery status registers for example.
- Remove some unused variables and #if 0'd debugging cruft.
- Don't complain about a GPE query that fails due to AE_NOT_FOUND if the
query method was _Q00.
from a BIF, use the size of the destinatino buffer, not the length of the
string to determine where to put the nul char. As a side effect, the
old code would truncate the string by one character while it was possibly
overflowing the buffer.
This piece of code has not been referenced since it was put there
in 1995. Also done a codebased search on popular networking libraries
and third-party applications. This is an orphan.
Reviewed by: jesper
o Allocate memory mapped by pcic even when not used for ncv.
This is for PC-Cards which needs offset, because I/O space should not be
used by other devices.
Pointed-out-by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
Incredibally useful for debugging kernels using vmware.
Vmware com1 is diverted to one side, and gdb listens to the other side.
viola.. instant debugging sandbox on one system.
Since we know there's always an upper bound we force that bound,
otherwise users can cause a panic via malloc getting hit with a
odd (huge or negative) amount of memory to allocate.
Tested by: kris
Pointed out by: Andrey Valyaev <dron@infosec.ru>
If you ever want to run midi(4) out of the giant lock, uncomment
MIDI_OUTOFGIANT in midi.h. Confirmed to work for csamidi with WITNESS
and INVARIANTS.
- midi_info, midi_open and seq_info are now tailqs, allowing arbitrary
numbers of devices to be configured.
- Do not send an active sensing message to reset midi modules.
- Clone /dev/sequencer*. /dev/sequencer0 and /dev/sequencer are generated
upon initialization.
Includes the following revisions from KAME (two of these were actually
committed previously but the CVS revisions weren't documented):
1.40 kame/kame/sys/netinet6/ah_core.c (committed in previous rev)
1.41 kame/kame/sys/netinet6/ah_core.c
1.28 kame/kame/sys/netinet6/ah_output.c (committed in previous rev)
1.29 kame/kame/sys/netinet6/ah_output.c
1.30 kame/kame/sys/netinet6/ah_output.c
1.129 kame/kame/sys/netinet6/nd6.c
1.130 kame/kame/sys/netinet6/nd6.c
1.24 kame/kame/sys/netinet6/dest6.c
1.25 kame/kame/sys/netinet6/dest6.c
Obtained from: KAME
- Convert to a more efficient queueing implementation.
- Don't allocate command buffers on the fly; simply work from a
static pool.
- Add a control device interface, for later use.
- Handle controller overload better as a consequence of the
improved queue implementation.
- Add support for the XPT_GET_TRAN_SETTINGS ccb, and correctly
set the virtual SCSI channels up for multiple outstanding I/Os.
- Update copyrights for 2001.
- Some whitespace fixes to improve readability.
Due to a misunderstanding on my part, previous versions of the
driver were limited to a single outstanding I/O per virtual drive.
Needless to say, this update improves performance substantially.
connection, but send it immediately. Prior to this change, it was possible
to delay a delayed-ack for multiple times, resulting in degraded TCP
behavior in certain corner cases.
o Offset and period in synch messages and width negotiation should be
done for per target not per lun. Move these from *lun_info to
*targ_info.
o Change in handling XPT_RESET_DEV and XPT_GET_TRAN_SETTINGS .
o Change CAM_* xpt_done return values.
o Busy loop did not timeout. Change this to timeout as original NetBSD/pc98.
Reviewed by: bsd-nomads ML
by the compiler. ie: char foo[0] comes out as 4 bytes on a.out, and
we depended on it coming out as 0 for the script version. :-(
Make double sure that genassym.o is built and nm'ed in elf mode.
(ia64 skipped since it is stuck on the linux toolchain and doesn't
understand the -elf switches)
gcc -aout -mno-underscores. The bioscall.s tweak is not an a.out
requirement really, but to work around the bugs in the antique version of
gas that used for a.out. Makefile hacks are all that is needed to
get an a.out kernel. There is no telling if it will work though.
This is little more than an academic curiosity anyway since all it is
good for is situations where the boot code is hard wired, eg: rom
bootstraps (such as the gnat box).
GENERIC:
...
size -aout kernel ; chmod 755 kernel
text data bss dec hex
3051520 368640 198688 3618848 373820
and used in C or vice versa. The elf compiler uses the same names
for both. Remove asnames.h with great prejudice; it has served its
purpose.
Note that this does not affect the ability to generate an aout kernel
due to gcc's -mno-underscores option.
moral support from: peter, jhb
ehternet frames to a netgraph hook.
Submitted by: "Vitaly V. Belekhov" <vitaly@riss-telecom.ru>
translated to 5.0 by me. man page not yet written.
This node still needs a little work.. don't use yet. Not yet linked into
the build.
This helps to stop it from geting out of sync.
It is not part of the normal build but I can use it with all the others
when I make changes to netgraph to ensure it is buildable.
to be more like Xint0x80_syscall and less like c function syscall().
- Reduce code duplication between the int0x80 and lcall handlers by
shuffling the elfags into the right place, saving the sizeof the
instruction in tf_err and jumping into the common int0x80 code.
Reviewed by: peter
passed in filename and line number in the KTR tracepoint message.
- Even though it is #if 0'd code, change the code to detect that a process
is an interrupt thread to check p->p_ithd against NULL rather than
checking non-existant process flags from BSD/OS.
- Use '%p' to print pointers in KTR log messages instead of assuming
sizeof(int) == sizeof(void *).
- Don't set p_mtxname to NULL when releasing a mutex. It doesn't hurt
to leave it set (we don't clear w_mesg for example) and at least at
one time in the past, there used to be race conditions in the kernel
that would result in setting this to NULL causing the kernel to
dereference NULL.
- Make the _mtx_assert() function be compiled in if INVARIANTS_SUPPORT is
defined rather than if INVARIANTS is defined so that a KLD compiled
with INVARIANTS that uses mtx_assert() can be used with a kernel that
just has INVARIANT_SUPPORT compiled in.
allow the watermark to be passed in via the data field during the EV_ADD
operation.
Hook this up to the socket read/write filters; if specified, it overrides
the so_{rcv|snd}.sb_lowat values in the filter.
Inspired by: "Ronald F. Guilmette" <rfg@monkeys.com>
the current socket error in fflags. This may be useful for determining
why a connect() request fails.
Inspired by: "Jonathan Graehl" <jonathan@graehl.org>
error will be passed up to the user, who will close the connection, so
it does not appear to make a sense to leave the connection open.
This also fixes a bug with kqueue, where the filter does not set EOF
on the connection, because the connection is still open.
Also remove calls to so{rw}wakeup, as we aren't doing anything with
them at the moment anyway.
Reviewed by: alfred, jesper
reset TCP connections which are in the SYN_SENT state, if the sequence
number in the echoed ICMP reply is correct. This behavior can be
controlled by the sysctl net.inet.tcp.icmp_may_rst.
Currently, only subtypes 2,3,10,11,12 are treated as such
(port, protocol and administrative unreachables).
Assocaiate an error code with these resets which is reported to the
user application: ENETRESET.
Disallow resetting TCP sessions which are not in a SYN_SENT state.
Reviewed by: jesper, -net
this information via the vm.nswapdev sysctl (number of swap areas)
and vm.swapdevX nodes (where X is the device), which contain the MIBs
dev, blocks, used, and flags. These changes are required to allow
top and other userland swap-monitoring utilities to run without
setgid kmem.
Submitted by: Thomas Moestl <tmoestl@gmx.net>
Reviewed by: freebsd-audit
and add a sysctl to pppoe to activate non standard ethertypes
so that idiot ISPs (apparently in France) who use
equipment from idiot suppliers (rumour says 3com)
who use nonstandard ethertypes can still connect.
"yep, sure we do pppoe, we use a different identifier to that dictated in
the standard, but sure it's pppoe!"
sysctl -w net.graph.stupid_isp=1 enables the changeover.
attached and ifconfigable. The card doesn't interrupt yet.
Also, move towards bus space by introducing new macros/inline
functions which make such a move much easier than before.
These inline functions are setup now to work around an IBM EtherJet
pccard cardbus bridge incompatibility. The card works in 8 bit mode,
but not in 16-bit mode when it is connected to a cardbus bridge for
reasons unknown. The Linux driver also has a similar workaround in
it.
Future work will include making the above workaround runtime
conditional rather than compile time conditional, as well as fixing
the interrupts in pccards and converting it to bus space.
for the ICB firmware options meant- *I* had taken it to
mean that if you set it, Node Name would be ignored and
derived from Port Name. Actually, it meant the opposite.
As a consequence- change ICBOPT_USE_PORTNAME to the
define ICBOPT_BOTH_WWNS- makes more sense.
Fix wrong input bitmap for MBOX_DUMP_RAM command. Call
ISP_DUMPREGS if we get a f/w crash. Add ISPCTL_RUN_MBOXCMD
control command (so outer layers can run a mailbox command
directly) and add a ISPASYNC_UNHANDLED_RESPONSE hook so
outer layers can understand response queue entries we
might not know about.
depend on this. The linux ABI emulator tries to use it for some linux
binaries too. VM86 had a bigger cost than this and it was made default
a while ago.
Reviewed by: jhb, imp
and 1.84 of src/sys/netinet/udp_usrreq.c
The changes broken down:
- remove 0 as a wildcard for addresses and port numbers in
src/sys/netinet/in_pcb.c:in_pcbnotify()
- add src/sys/netinet/in_pcb.c:in_pcbnotifyall() used to notify
all sessions with the specific remote address.
- change
- src/sys/netinet/udp_usrreq.c:udp_ctlinput()
- src/sys/netinet/tcp_subr.c:tcp_ctlinput()
to use in_pcbnotifyall() to notify multiple sessions, instead of
using in_pcbnotify() with 0 as src address and as port numbers.
- remove check for src port == 0 in
- src/sys/netinet/tcp_subr.c:tcp_ctlinput()
- src/sys/netinet/udp_usrreq.c:udp_ctlinput()
as they are no longer needed.
- move handling of redirects and host dead from in_pcbnotify() to
udp_ctlinput() and tcp_ctlinput(), so they will call
in_pcbnotifyall() to notify all sessions with the specific
remote address.
Approved by: jlemon
Inspired by: NetBSD
interrupts.
Protect usage of the per processor switchtime variable against
interrupts in calcru().
This seem to eliminate the "microuptime() went backwards" warnings.
the the original trapframe of the syscall, trap, or interrupt that entered
the kernel. Before SMPng, ast's were handled via a psuedo trap at the
end of doerti. With the SMPng commit, ast's were broken out into a
separate ast() function that was called from doreti to match the behavior
of other architectures. Unfortunately, when this was done, the
p_md.md_regs member of curproc was not updateda in ast(), thus when
signals are handled by userret() after an interrupt that returns to
userland, we end up using a stale trapframe that will result in the
registers from the old trapframe overwriting the real trapframe and
smashing all the registers right before we return to usermode. The saved
%cs:%eip from where we were in usermode are saved in the trapframe for
example.
- Don't use an atomic operation to update cnt.v_soft in ast(). This is
the only place the variable is written to, and sched_lock is always
held when it is written, so it is already protected and the mutex release
of sched_lock asserts a memory barrier that ensures the value will be
updated in a timely fashion.
packet flow into two unidirectional flows.
Part of a suite of nodes developed for packet flow control.
More to follow as I have time to port them to 5.x or
as others do so. The ipfw node will be the hardest..
Submitted by: "Vitaly V. Belekhov" <vitaly@riss-telecom.ru>
- Remove unneeded spl()'s around mi_switch() in userret().
- Don't hold sched_lock across addupc_task().
- Remove the MD function child_return() now that the MI function
fork_return() is used instead.
- Use TRAPF_USERMODE() instead of dinking with the trapframe directly to
check for ast's in kernel mode.
- Check astpending(curproc) and resched_wanted() in ast() and return if
neither is true.
- Use astoff() rather than setting the non-existent per-cpu variable
astpending to 0 to clear an ast.
- Don't hold sched_lock around addupc_task() as this apparently breaks
profiling badly due to sched_lock being held across copyin().
Reported by: bde (2)
for us.
- Change the switch_trampoline() to call fork_exit() passing in the
required arguments instead of calling the fork trampoline callout
function directly.
Warning: this hasn't been tested.
Looked over by: dfr
an interrupt thread while the interrupt thread is blocked on Giant waiting
to execute the interrupt handler being removed. The result was that the
intrhand structure would be free'd, and we would call 0xdeadc0de. The work
around is to check to see if the interrupt thread is idle when removing a
handler. If not, then we mark the interrupt handler as being dead using
the new IH_DEAD flag and don't remove it from the interrupt threads' list
of handlers. When the interrupt thread resumes, it will see a dead handler
while traversing the list of handlers and will remove the handler then.
