These functions were dropped originally because I felt they would
need to be rewritten anyway to avoid using uios. However, this
patch readds then with they dea they can just be reworked and
the uio bits dropped.
During a rename we need to be careful to destroy and create a
new minor for the ZVOL _only_ if the rename succeeded. The previous
code would both destroy you minor device unconditionally, it would
also fail to create the new minor device on success.
These compiler warnings were introduced when code which was
previously #ifdef'ed out by HAVE_ZPL was re-added for use
by the posix layer. All of the following changes should be
obviously correct and will cause no semantic changes.
The issue is that cv_timedwait() sleeps uninterruptibly to block signals
and avoid waking up early. Under Linux this counts against the load
average keeping it artificially high. This change allows the arc to
sleep interruptibly which mean it may be woken up early due to a signal.
Normally this means some extra care must be taken to handle a potential
signal. But for the arcs usage of cv_timedwait() there is no harm in
waking up before the timeout expires so no extra handling is required.
This commit fixes a sign extension bug affecting l2arc devices. Extremely
large offsets may be passed down to the low level block device driver on
reads, generating errors similar to
attempt to access beyond end of device
sdbi1: rw=14, want=36028797014862705, limit=125026959
The unwanted sign extension occurrs because the function arc_read_nolock()
stores the offset as a daddr_t, a 32-bit signed int type in the Linux kernel.
This offset is then passed to zio_read_phys() as a uint64_t argument, causing
sign extension for values of 0x80000000 or greater. To avoid this, we store
the offset in a uint64_t.
This change also changes a few daddr_t struct members to uint64_t in the libspl
headers to avoid similar bugs cropping up in the future. We also add an ASSERT
to __vdev_disk_physio() to check for invalid offsets.
Closes#66
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The name of the flag used to mark a bio as synchronous has changed
again in the 2.6.36 kernel due to the unification of the BIO_RW_*
and REQ_* flags. The new flag is called REQ_SYNC. To simplify
checking this flag I have introduced the vdev_disk_dio_is_sync()
helper function. Based on the results of several new autoconf
tests it uses the correct mask to check for a synchronous bio.
Preferred interface for flagging a synchronous bio:
2.6.12-2.6.29: BIO_RW_SYNC
2.6.30-2.6.35: BIO_RW_SYNCIO
2.6.36-2.6.xx: REQ_SYNC
Commit 3ee56c292b changed an ENOTSUP return value
in one location to ENOTSUPP to fix user programs seeing an invalid ioctl()
error code. However, use of ENOTSUP is widespread in the zfs module. Instead
of changing all of those uses, we fixed the ENOTSUP definition in the SPL to be
consistent with user space. The changed return value in the above commit is
therefore no longer needed, so this commit reverses it to maintain consistency.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Support for rolling back datasets require a functional ZPL, which we currently
do not have. The zfs command does not check for ZPL support before attempting
a rollback, and in preparation for rolling back a zvol it removes the minor
node of the device. To prevent the zvol device node from disappearing after a
failed rollback operation, this change wraps the zfs_do_rollback() function in
an #ifdef HAVE_ZPL and returns ENOSYS in the absence of a ZPL. This is
consistent with the behavior of other ZPL dependent commands such as mount.
The orginal error message observed with this bug was rather confusing:
internal error: Unknown error 524
Aborted
This was because zfs_ioc_rollback() returns ENOTSUP if we don't HAVE_ZPL, but
Linux actually has no such error code. It should instead return EOPNOTSUPP, as
that is how ENOTSUP is defined in user space. With that we would have gotten
the somewhat more helpful message
cannot rollback 'tank/fish': unsupported version
This is rather a moot point with the above changes since we will no longer make
that ioctl call without a ZPL. But, this change updates the error code just in
case.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Increasing the default zio_wr_int thread count from 8 to 16 improves
write performence by 13% on large systems. More testing need to be
done but I suspect the ideal tuning here is ZTI_BATCH() with a minimum
of 8 threads.
Linux kernel thread names are expected to be short. This change shortens
the zio thread names to 10 characters leaving a few chracters to append
the /<cpuid> to which the thread is bound. For example: z_wr_iss/0.
On some older kernels, i.e. 2.6.18, zvol_ioctl_by_inode() may get passed a NULL
file pointer if the user tries to mount a zvol without a filesystem on it.
This change adds checks to prevent a null pointer dereference.
Closes#73.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
It turns out that 'zpool events' over 1024 bytes in size where being
silently dropped. This was discovered while writing the zfault.sh
tests to validate common failure modes.
This could occur because the zfs interface for passing an arbitrary
size nvlist_t over an ioctl() is to provide a buffer for the packed
nvlist which is usually big enough. In this case 1024 byte is the
default. If the kernel determines the buffer is to small it returns
ENOMEM and the minimum required size of the nvlist_t. This was
working properly but in the case of 'zpool events' the event stream
was advanced dispite the error. Thus the retry with the bigger
buffer would succeed but it would skip over the previous event.
The fix is to pass this size to zfs_zevent_next() and determine
before removing the event from the list if it will fit. This was
preferable to checking after the event was returned because this
avoids the need to rewind the stream.
While there is no right maximum timeout for a disk IO we can start
laying the ground work to measure how long they do take in practice.
This change simply measures the IO time and if it exceeds 30s an
event is posted for 'zpool events'.
This value was carefully selected because for sd devices it implies
that at least one timeout (SD_TIMEOUT) has occured. Unfortunately,
even with FAILFAST set we may retry and request and not get an
error. This behavior is strongly dependant on the device driver
and how it is hooked in to the scsi error handling stack. However
by setting the limit at 30s we can log the event even if no error
was returned.
Slightly longer term we can start recording these delays perhaps
as a simple power-of-two histrogram. This histogram can then be
reported as part of the 'zpool status' command when given an command
line option.
None of this code changes the internal behavior of ZFS. Currently
it is simply for reporting excessively long delays.
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
By default the Solaris code does not log speculative or soft io errors
in either 'zpool status' or post an event. Under Linux we don't want
to change the expected behavior of 'zpool status' so these io errors
are still suppressed there.
However, since we do need to know about these events for Linux FMA and
the 'zpool events' interface is new we do post the events. With the
addition of the zio_flags field the posted events now contain enough
information that a user space consumer can identify and discard these
events if it sees fit.
All the upper layers of zfs expect zio->io_error to be positive. I was
careful but I missed one instance in vdev_disk_physio_completion() which
could return a negative error. To ensure all cases are always caught I
had additionally added an ASSERT() to check this before zio_interpret().
Finally, as a debugging aid when zfs is build with --enable-debug all
errors from the backing block devices will be reported to the console
with an error message like this:
ZFS: zio error=5 type=1 offset=4217856 size=8192 flags=60440
Observed during failure mode testing, dsl_scan_setup_sync() allocates
73920 bytes. This is way over the limit of what is wise to do with a
kmem_alloc() and it should probably be moved to a slab. For now I'm
just flagging it with KM_NODEBUG to quiet the error until this can be
revisited.
This commit fixes a bug in vdev_disk_open() in which the whole_disk property
was getting set to 0 for disk devices, even when it was stored as a 1 when the
zpool was created. The whole_disk property lets us detect when the partition
suffix should be stripped from the device name in CLI output. It is also used
to determine how writeback cache should be set for a device.
When an existing zpool is imported its configuration is read from the vdev
label by user space in zpool_read_label(). The whole_disk property is saved in
the nvlist which gets passed into the kernel, where it in turn gets saved in
the vdev struct in vdev_alloc(). Therefore, this value is available in
vdev_disk_open() and should not be overridden by checking the provided device
path, since that path will likely point to a partition and the check will
return the wrong result.
We also add an ASSERT that the whole_disk property is set. We are not aware of
any cases where vdev_disk_open() should be called with a config that doesn't
have this property set. The ASSERT is there so that when debugging is enabled
we can identify any legitimate cases that we are missing. If we never hit the
ASSERT, we can at some point remove it along with the conditional whole_disk
check.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This callback is needed for properly accounting the per-uid and per-gid
space usage. Even if we don't have the ZPL, we still need this callback
in order to have proper on-disk ZPL compatibility and to be able to use
Lustre quotas.
Fortunately, the callback doesn't have any ZPL/VFS dependencies so we
can just move it out of #ifdef HAVE_ZPL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Required for the DB_DNODE_ENTER()/DB_DNODE_EXIT() helpers.
Signed-off-by: Ricardo M. Correia <ricardo.correia@oracle.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In my machine, dnode_hold_impl() allocates 9992 bytes in DEBUG mode and it
causes a large stream of stack traces in the logs. Instead, use KM_NODEBUG
to quiet down this known large alloc.
Signed-off-by: Ricardo M. Correia <ricardo.correia@oracle.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
This topic branch contains all the changes needed to integrate the user
side zfs tools with Linux style devices. Primarily this includes fixing
up the Solaris libefi library to be Linux friendly, and integrating with
the libblkid library which is provided by e2fsprogs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The upstream ZFS code has correctly moved to a faster native sha2
implementation. Unfortunately, under Linux that's going to be a little
problematic so we revert the code to the more portable version contained
in earlier ZFS releases. Using the native sha2 implementation in Linux
is possible but the API is slightly different in kernel version user
space depending on which libraries are used. Ideally, we need a fast
implementation of SHA256 which builds as part of ZFS this shouldn't be
that hard to do but it will take some effort.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This branch contains the majority of the changes required to cleanly
intergrate with Linux style special devices (/dev/zfs). Mainly this
means dropping all the Solaris style callbacks and replacing them
with the Linux equivilants.
This patch also adds the onexit infrastructure needed to track
some minimal state between ioctls. Under Linux it would be easy
to do this simply using the file->private_data. But under Solaris
they apparent need to pass the file descriptor as part of the ioctl
data and then perform a lookup in the kernel. Once again to keep
code change to a minimum I've implemented the Solaris solution.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The ZFS update to onnv_141 brought with it support for a
security label attribute called mlslabel. This feature
depends on zones to work correctly and thus I am disabling
it under Linux. Equivilant functionality could be added
at some point in the future.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch leverages the Solaris style FMA call points
in ZFS to create a user space visible event notification system
under Linux. This new system is called zevent and it unifies
all previous Solaris style ereports and sysevent notifications.
Under this Linux specific scheme when a sysevent or ereport event
occurs an nvlist describing the event is created which looks almost
exactly like a Solaris ereport. These events are queued up in the
kernel when they occur and conditionally logged to the console.
It is then up to a user space application to consume the events
and do whatever it likes with them.
To make this possible the existing /dev/zfs ABI has been extended
with two new ioctls which behave as follows.
* ZFS_IOC_EVENTS_NEXT
Get the next pending event. The kernel will keep track of the last
event consumed by the file descriptor and provide the next one if
available. If no new events are available the ioctl() will block
waiting for the next event. This ioctl may also be called in a
non-blocking mode by setting zc.zc_guid = ZEVENT_NONBLOCK. In the
non-blocking case if no events are available ENOENT will be returned.
It is possible that ESHUTDOWN will be returned if the ioctl() is
called while module unloading is in progress. And finally ENOMEM
may occur if the provided nvlist buffer is not large enough to
contain the entire event.
* ZFS_IOC_EVENTS_CLEAR
Clear are events queued by the kernel. The kernel will keep a fairly
large number of recent events queued, use this ioctl to clear the
in kernel list. This will effect all user space processes consuming
events.
The zpool command has been extended to use this events ABI with the
'events' subcommand. You may run 'zpool events -v' to output a
verbose log of all recent events. This is very similar to the
Solaris 'fmdump -ev' command with the key difference being it also
includes what would be considered sysevents under Solaris. You
may also run in follow mode with the '-f' option. To clear the
in kernel event queue use the '-c' option.
$ sudo cmd/zpool/zpool events -fv
TIME CLASS
May 13 2010 16:31:15.777711000 ereport.fs.zfs.config.sync
class = "ereport.fs.zfs.config.sync"
ena = 0x40982b7897700001
detector = (embedded nvlist)
version = 0x0
scheme = "zfs"
pool = 0xed976600de75dfa6
(end detector)
time = 0x4bec8bc3 0x2e5aed98
pool = "zpios"
pool_guid = 0xed976600de75dfa6
pool_context = 0x0
While the 'zpool events' command is handy for interactive debugging
it is not expected to be the primary consumer of zevents. This ABI
was primarily added to facilitate the addition of a user space
monitoring daemon. This daemon would consume all events posted by
the kernel and based on the type of event perform an action. For
most events simply forwarding them on to syslog is likely enough.
But this interface also cleanly allows for more sophisticated
actions to be taken such as generating an email for a failed drive.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add autoconf style build infrastructure to the ZFS tree. This
includes autogen.sh, configure.ac, m4 macros, some scripts/*,
and makefiles for all the core ZFS components.
Due to limited stack space recursive functions are frowned upon in
the Linux kernel. However, they often are the most elegant solution
to a problem. The following code preserves the recursive function
traverse_visitbp() but moves the local variables AND function
arguments to the heap to minimize the stack frame size. Enough
space is initially allocated on the stack for 20 levels of recursion.
This change does ugly-up-the-code but it reduces the worst case
usage from roughly 4160 bytes to 960 bytes on x86_64 archs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Implement zio_execute() as a wrapper around the static function
__zio_execute() so that we can force __zio_execute() to be inlined.
This reduces stack overhead which is important because __zio_execute()
is called recursively in several zio code paths. zio_execute() itself
cannot be inlined because it is externally visible.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Eliminated local variables pointing to members of the zio struct.
Just refer to the struct members directly. This saved about 32 bytes per
call, but this function can be called recurisvely up to 19 levels deep,
so we potentially save up to 608 bytes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Certain function must never be automatically inlined by gcc because
they are stack heavy or called recursively. This patch flags all
such functions I've found as 'noinline' to prevent gcc from making
the optimization.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reduce kernel stack usage by lzjb_compress() by moving uint16 array
off the stack and on to the heap. The exact performance implications
of this I have not measured but we absolutely need to keep stack
usage to a minimum. If/when this becomes and issue we optimize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Decrease stack usage for various call paths by forcing certain
functions to be inlined. By inlining the functions the overhead
of a new stack frame is removed at the cost of increased code size.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
To reduce stack overhead this topic branch moves the 128 byte
blkptr_t data strucutre in dsl_scan_visitbp() to the heap.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reduce stack usage in dsl_deleg_get, gcc flagged it as consuming a
whopping 1040 bytes or potentially 1/4 of a 4K stack. This patch
moves all the large structures and buffer off the stack and on to
the heap. This includes 2 zap_cursor_t structs each 52 bytes in
size, 2 zap_attribute_t structs each 280 bytes in size, and 1
256 byte char array. The total saves on the stack is 880 bytes
after you account for the 5 new pointers added.
Also the source buffer length has been increased from MAXNAMELEN
to MAXNAMELEN+strlen(MOS_DIR_NAME)+1 as described by the comment in
dsl_dir_name(). A buffer overrun may have been possible with the
slightly smaller buffer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
