Like the detailed diagnostics produced when a bad superblock
is read, provide similar detailed diagnostics when bad
cylinder groups are read.
Reported by: Peter Holm
Tested by: Peter Holm
Sponsored by: The FreeBSD Foundation
The fsck_ffs(8) utility has two subsystems for reading and writing
inodes. The getnextinode() interface is used in Pass 1 (and Pass
1b if needed) to sequentially walk through all the inodes in the
filesystem. The ginode() interface is used to read and write
individual inodes. Pass 1 uses a mix of both interfaces. This
change ensures that ginode() returns a pointer to the inode in the
cache maintained by getnextinode() when that interface holds the
requested inode so that all modifications to the inode are made in
a single place and are all written to the disk together.
Reported by: Peter Holm
Tested by: Peter Holm
Sponsored by: The FreeBSD Foundation
Historically fsck_ffs(8) would only use alternate superblocks when
running in manual mode. When the standard superblock fails, it now
tries to find and use a backup superblocks even when running in `preen'
mode. If an alternate superblock is found and the filesystem is
successfully cleaned up using it, write the alternate superblock
back to the standard superblock so that the filesystem can be
subsequently mounted and used.
Reported by: Peter Holm
Tested by: Peter Holm
Sponsored by: The FreeBSD Foundation
The UFS filesystem expects to find '.' and '..' as the first two entries
in a directory. The kernel's UFS name cache can become quite confused
when these two entries are not present as the first two entries.
Prior to this change, when the fsck_ffs(8) utility detected that
'.' and/or '..' were missing, it would report them, but only offered
to replace them if the space at the beginning of the directory was
available. Otherwise it was left to the system administrator to
move the offending file(s) out of the way and then rerun fsck_ffs(8)
to create the '.' and '..' entries.
With this change, fsck_ffs(8) will always be able to create the '.'
and/or '..' entries. It moves any files in the way elsewhere in the
directory block. If there is no room in the directory block to which
to move them, they are placed in the lost+found directory.
Reported by: Peter Holm
Sponsored by: The FreeBSD Foundation
When either searching for backup UFS superblocks or when explicitly asked
to use one with the -b option, report the reason for failure if it cannot
be used.
Reported by: Peter Holm
Sponsored by: The FreeBSD Foundation
Add a descrition to the tunefs(8) -j (journal enablement) flag
that explains what soft updates journaling does, the tradeoffs
to using it, and the limitations that it imposes.
Requested by: Graham Perrin
PR: 261944
Sponsored by: The FreeBSD Foundation
Allocation or I/O failures in fsck_ffs(8) could cause segment
faults because of missing checks or not-yet-initialized data
structures. Correct these issues.
Reported by: Peter Holm
Sponsored by: The FreeBSD Foundation
into ffs_sbsearch() to allow use by other parts of the system.
Historically only fsck_ffs(8), the UFS filesystem checker, had code
to track down and use alternate UFS superblocks. Since fsdb(8) used
much of the fsck_ffs(8) implementation it had some ability to track
down alternate superblocks.
This change extracts the code to track down alternate superblocks
from fsck_ffs(8) and puts it into a new function ffs_sbsearch() in
sys/ufs/ffs/ffs_subr.c. Like ffs_sbget() and ffs_sbput() also found
in ffs_subr.c, these functions can be used directly by the kernel
subsystems. Additionally they are exported to the UFS library,
libufs(8) so that they can be used by user-level programs. The new
functions added to libufs(8) are sbfind(3) that is an alternative
to sbread(3) and sbsearch(3) that is an alternative to sbget(3).
See their manual pages for further details.
The utilities that have been changed to search for superblocks are
dumpfs(8), fsdb(8), ffsinfo(8), and fsck_ffs(8). Also, the prtblknos(8)
tool found in tools/diag/prtblknos searches for superblocks.
The UFS specific mount code uses the superblock search interface
when mounting the root filesystem and when the administrator doing
a mount(8) command specifies the force flag (-f). The standalone UFS
boot code (found in stand/libsa/ufs.c) uses the superblock search
code in the hope of being able to get the system up and running so
that fsck_ffs(8) can be used to get the filesystem cleaned up.
The following utilities have not been changed to search for
superblocks: clri(8), tunefs(8), snapinfo(8), fstyp(8), quot(8),
dump(8), fsirand(8), growfs(8), quotacheck(8), gjournal(8), and
glabel(8). When these utilities fail, they do report the cause of
the failure. The one exception is the tasting code used to try and
figure what a given disk contains. The tasting code will remain
silent so as not to put out a slew of messages as it trying to taste
every new mass storage device that shows up.
Reviewed by: kib
Reviewed by: Warner Losh
Tested by: Peter Holm
Differential Revision: https://reviews.freebsd.org/D36053
Sponsored by: The FreeBSD Foundation
When the interface does not exist avoid passing host with special pf
modifiers to DNS resolution as they come up empty anyway.
Reviewed by: kp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D35429
In 1e73fbd8b we fixed an issue with POM_STICKYADDRESS being checked in
the wrong struct.
Add a basic test case for this fix.
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC ("Netgate")
pass inet proto icmp icmp-type {unreach}
pass route-to (if0 127.0.0.1/8) sticky-address inet
The wrong struct was being tested. The parser tries to prevent
"sticky-address sticky-address" syntax but was actually cross-rule
enforcing that ICMP filter cannot be before the use of "sticky-address"
in next rule.
MFC after: 2 weeks
Reviewed by: kp
Differential Revision: https://reviews.freebsd.org/D36050
The fsck_ffs(8) utility made sanity checks of critical superblock
fields by comparing the values of those fields in the standard
superblock againt the values of those fields in the last alternate
superblock. The code for validating a superblock now cover all the
checked fields as well as many more. Further the checks done are
far more comprehensive. So we now drop the alternate superblock
checks as they no longer provide value. Dropping these checks also
eliminates the need to read the alternate superblock.
Rather than trying to shoehorn flags into the requested superblock
address, create a separate flags parameter to the ffs_sbget()
function in sys/ufs/ffs/ffs_subr.c. The ffs_sbget() function is
used both in the kernel and in user-level utilities through export
to the sbget() function in the libufs(3) library (see sbget(3)
for details). The kernel uses ffs_sbget() when mounting UFS
filesystems, in the glabel(8) and gjournal(8) GEOM utilities,
and in the standalone library used when booting the system
from a UFS root filesystem.
The ffs_sbget() function reads the superblock located at the byte
offset specified by its sblockloc parameter. The value UFS_STDSB
may be specified for sblockloc to request that the standard
location for the superblock be read.
The two existing options are now flags:
UFS_NOHASHFAIL will note if the check hash is wrong but will still
return the superblock. This is used by the bootstrap code to
give the system a chance to come up so that fsck can be run to
correct the problem.
UFS_NOMSG indicates that superblock inconsistency error messages
should not be printed. It is used by programs like fsck that
want to print their own error message and programs like glabel(8)
that just want to know if a UFS filesystem exists on a partition.
One additional flag is added:
UFS_NOCSUM causes only the superblock itself to be returned, but does
not read in any auxiliary data structures like the cylinder group
summary information. It is used by clients like glabel(8) that
just want to check for possible filesystem types. Using UFS_NOCSUM
skips the superblock checks for csum data which allows superblocks
that have corrupted csum data to be read and used.
The validate_sblock() function checks that the superblock has not
been corrupted in a way that can crash or hang the system. Unless
the UFS_NOMSG flag is specified, it will print out any errors that
it finds. Prior to this commit, validate_sblock() returned as soon
as it found an inconsistency so would print at most one message.
It now does all its checks so when UFS_NOMSG has not been specified
will print out everything that it finds inconsistent.
Sponsored by: The FreeBSD Foundation
The reported problem is that some geli commands exit with a
success status when they should exit with a failed status.
The gctl_error() function is defined differently in the kernel
(in sys/geom/geom_ctl.c) versus in the geom user facilities (in
sbin/geom/misc/subr.c). In the kernel, calling gctl_error() causes
an error return to be set while in the user version it does not.
It was only by a quirk that had been added to the user geom return
processing that I "cleaned up" that the lack of the user implementaion
to set the error return showed up.
This patch adds the missing setting of the error code when calling
the user facility gctl_error().
Reported by: Jenkins
Debugging by: Alan Somers
Debugging by: Cy Schubert
Debugging by: Li-Wen Hsu
The BSD style commands (with names not ending in "sum") ignored the -c
options and the passed digest value when invoked with -q.
The man page stated that -q causes only the calculated digest to be
printed, but did not consider the case of both the -q and -c being
used in combination.
Since there is no warning that -c will be ignored when the -q option
is used, users night (and did) expect that the exit code would reflect
the matching of the calculated digest and the argument passed with -c.
This update implements and documents this expected behavior.
PR: 265461
Reported by: Dmitrij <bugs.freebsd@1fff.net>
MFC after: 2 weeks
The setvlantag() and setvlanproto() functions are used in two scenarios:
when we create a new vlan interface and when we update an existing
interface.
These are distinguished by the getvlan() at the end of the functions. If
this fails we assume that is because the interface doesn't exist (so
we're creating a new one). We only update the 'params' struct, and
expect the settings to be applied when we vlan_create().
However, if we're updating an existing interface we do not retrieve the
current settings, and can end up invalidating settings.
Fix this by using the settings we retrieved while checking which
scenario we're in.
Note that we do not address this for setvlandev(), because if_vlan does
not allow the vlan parent device to be changed without disassociating it
first (with ifconfig vlanX -vlandev).
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D35848
Only the UFS2 filesystem has support for storing information needed
to find alternate superblocks. If that information is inadvertently
left in place when building a UFS1 filesystem, fsck_ffs may stumble
across it and attempt to use it to recover the UFS1 filesystem
which can only end poorly.
During software installation, use veriexec -S to strictly
enforce certificate validity checks (notBefore, notAfter).
Otherwise ignore certificate validity period.
It is generally unacceptible for the Internet to stop working
just because someone did not upgrade their infrastructure for a decade.
Sponsored by: Juniper Networks, Inc.
Reviewed by: sebastien.bini_stormshield.eu
Differential Revision: https://reviews.freebsd.org/D35758
Generally, access to the kernel debugger is considered to be unsafe from
a security perspective since it presents an unrestricted interface to
inspect or modify the system state, including sensitive data such as
signing keys.
However, having some access to debugger functionality on production
systems may be useful in determining the cause of a panic or hang.
Therefore, it is desirable to have an optional policy which allows
limited use of ddb(4) while disabling the functionality which could
reveal system secrets.
This loadable MAC module allows for the use of some ddb(4) commands
while preventing the execution of others. The commands have been broadly
grouped into three categories:
- Those which are 'safe' and will not emit sensitive data (e.g. trace).
Generally, these commands are deterministic and don't accept
arguments.
- Those which are definitively unsafe (e.g. examine <addr>, search
<addr> <value>)
- Commands which may be safe to execute depending on the arguments
provided (e.g. show thread <addr>).
Safe commands have been flagged as such with the DB_CMD_MEMSAFE flag.
Commands requiring extra validation can provide a function to do so.
For example, 'show thread <addr>' can be used as long as addr can be
checked against the system's list of process structures.
The policy also prevents debugger backends other than ddb(4) from
executing, for example gdb(4).
Reviewed by: markj, pauamma_gundo.com (manpages)
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D35371
Historically, GEOM utilities (gpart(8), gstripe(8), gmirror(8),
etc) used the gctl_error() routine to report errors. If they called
gctl_error() they would exit with EXIT_FAILURE, otherwise they would
return with EXIT_SUCCESS. If they used gctl_error() to output an
informational message, for example when run with the -v (verbose)
option, they would mistakenly exit with EXIT_FAILURE. A further
limitation of the gctl_error() function was that it could only be
called once. Messages from any additional calls to gctl_error()
would be silently discarded.
To resolve these problems a new function, gctl_msg() has been added.
It can be called multiple times to output multiple messages. It
also has an additional errno argument which should be zero if it is
an informational message or an errno value (EINVAL, EBUSY, etc) if
it is an error. When done the gctl_post_messages() function should
be called to indicate that all messages have been posted. If any
of the messages had a non-zero errno, the utility will EXIT_FAILURE.
If only informational messages (with zero errno) were posted, the
utility will EXIT_SUCCESS.
Tested by: Peter Holm
PR: 265184
MFC after: 1 week
Replace ppp(4) removed since FreeBSD 8.0-RELEASE with vlan(4).
While here, remove commented out reference to non-existing "egress"
interface group hiding since initial import of interface groups
from OpenBSD in 2006.
Jails without VNET have complete access to the ipfilter rules, NAT,
pools and logs. This is insecure. Only allow jails to manipulate
ipfilter rules, NAT tables and ippools if the jail has its own VNET.
Otherwise a jail can affect the global system.
This patch brings ipfilter in line with ipfw's support of VNET jails and
non-support of non-VNET jails.
MFC after: 1 week
If the "intr" and/or "soft" mount options are used for
NFSv4 mounts, the protocol can be broken when the
operation returns without waiting for the RPC reply.
The likelyhood of failure increases for NFSv4.1/4.2
mounts, since the session slot will be broken when
an RPC reply is not processed.
This is mentioned in the BUGS section of "man mount_nfs",
but there was no specific mention of the session slot
problem. This patch adds a sentence for this case.
PR: 260011
Reviewed by: gbe
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D35693
If the "intr" and/or "soft" mount options are used for
NFSv4 mounts, the protocol can be broken when the
operation returns without waiting for the RPC reply.
The likelyhood of failure increases for NFSv4.1/4.2
mounts, since the session slot will be broken when
an RPC reply is not processed.
This is mentioned in the BUGS section of "man mount_nfs",
but more needs to be done. This patch adds code that
generates a warning message when the mount is done.
PR: 260011
Reviewed by: emaste
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D35407
Provide more robust parameter parsing in veriexec. Do a little cleanup as well.
Differential revision: https://reviews.freebsd.org/D33246
Obtained from: Semihalf
Reviewed by: sjg, sebastien.bini_stormshield.eu
When growing a UFS/FFS filesystem, the size of the summary information
may expand into additional blocks. These blocks must be removed from
fs_dsize which records the number of blocks in the filesystem that can
be used to hold filesystem data.
While here also update the fs_old_dsize and fs_old_size fields for
compatibility with kernels that were compiled before the addition
of UFS2.
Reported by: Edward Tomasz Napiera
MFC after: 1 week
Any field that starts with # is a commented out field (there as a place
holder only, the data in that place holder is completely ignored). The
previous code improperly detected this using strcmp. Instead, any field
whose names starts with '#' is ignored.
Differential Reivsion: https://reviews.freebsd.org/D34633
named(8) hasn't been in base for some time. Remove all references to it in
manual pages.
Approved by: manpages (Pau Amma)
Differential Revision: https://reviews.freebsd.org/D35586
It may happen that "adjkerntz -a" called from jailed root crontab.
In that case it spams logs with a line:
sysctl(set: "machdep.wall_cmos_clock"): Operation not permitted
Be silent in that case.
MFC after: 1 month
The current situation is fairly confusing, where an integer is interpreted
as a percent until you slap a decimal on it and magically it becomes an
absolute value.
Let's have a flag day in 14.0 and remove this shim entirely. Setting with
percent can still be useful, so allow a trailing '%' to indicate as such.
As a side effect, we tighten down the format allowed in the volume a little
bit by ensuring there's no trailing garbage after the value once it's
separated into left and right components.
Reviewed by: christos, hselasky, pauamma_gundo.com (manpages)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D35101
Honor -q parameter and do not display any warning messages when -q is
specified.
Approved by: dfr
MFC after: 2 weeks
Sponsored by: Resulta, s.r.o.
Differential Revision: https://reviews.freebsd.org/D35511
It may not be known at compile time so we should detect it at run time.
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D35118
If isc-dhcp44-server is not installed (as is the case the project's CI
servers) we don't create ngctl.shutdown, causing the 'rm' to fail.
That in turn causes the cleanup function to return non-zero, which
causes kyua to consider the test failed.
Use 'rm -f' instead, so we don't error even if the file doesn't exist.
Sponsored by: Rubicon Communications, LLC ("Netgate")
They are no longer needed, but were likely missed simply because they
don't show up in a grep for 'mips'.
Reviewed by: emaste
Differential Revision: https://reviews.freebsd.org/D35475
This avoids the need to drop into the ddb to figure out vnode
usage per file system. It helps to see if they are or are not
being freed. Suggestion to report active vnode count was from
kib@
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D35436
By analogy with IP address matching, add a way to use ipfw radix
tables for MAC matching. This is implemented using new ipfw table
with mac:radix type. Also there are src-mac and dst-mac lookup
commands added.
Usage example:
ipfw table 1 create type mac
ipfw table 1 add 11:22:33:44:55:66/48
ipfw add skipto tablearg src-mac 'table(1)'
ipfw add deny src-mac 'table(1, 100)'
ipfw add deny lookup dst-mac 1
Note: sysctl net.link.ether.ipfw=1 should be set to enable ipfw
filtering on L2.
Reviewed by: melifaro
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D35103
mount_nfs creates entries in the mounttab file and umount removes
them. Entries in the mounttab file ae used by rpc.umntall to
notify the NFS server that NFSv3 entries need to be removed when
they have not been removed by umount.
Without this patch, an enty will be created in the mounttab file,
even if the nmount(2) syscall fails for the mount. This patch
modifies the code so that the mounttab entry is only created
after nmount(2) succeeds.
This change only affects NFSv3 and only affects how showmount
displays NFSv3 mounts.
MFC after: 2 weeks
Provide sticky ARP flag for network interface which marks it as the
"sticky" one similarly to what we have for bridges. Once interface is
marked sticky, any address resolved using the ARP will be saved as a
static one in the ARP table. Such functionality may be used to prevent
ARP spoofing or to decrease latencies in Ethernet networks.
The drawbacks include potential limitations in usage of ARP-based
load-balancers and high-availability solutions such as carp(4).
The implemented option is disabled by default, therefore should not
impact the default behaviour of the networking stack.
Sponsored by: Conclusive Engineering sp. z o.o.
Reviewed By: melifaro, pauamma_gundo.com
Differential Revision: https://reviews.freebsd.org/D35314
MFC after: 2 weeks
This tests both both normal (untagged), and pcp tagged (VLAN 0)
networks which are now common for fiber ISPs.
Reviewed by: markj, kp
Differential Revision: https://reviews.freebsd.org/D35178
/etc/rc.d/jail no longer creates /dev/log as a symbolic link since
commit 84b354cb9a.
PR: 228351
Reviewed by: jamie, mark
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D34563
If pfctl is called with "pfctl -a ''" we read outside of the anchoropt
buffer. Check that the buffer is sufficiently long to avoid that.
Maintain the existing (and desired, because it's used as such in
/etc/periodic/security/520.pfdenied) behaviour of treating "-a ''" as a
request for the root anchor (or no anchor specified).
PR: 264128
Reviewed by: kp
The command "ping -S dotted.quad hostname" fails on dual-stack hosts
with the confusing message "ping: invalid source address: Name does
not resolve" because IPv6 is selected in preference. If the argument
to -S is numeric (likely), select the corresponding address family,
as if -4 or -6 was specified. Add tests that either IPv4 or IPv6 can
be forced via a -S parameter.
Reviewed by: asomers
Differential Revision: https://reviews.freebsd.org/D35271
MFC after: 1 week
Previously we expected the DIOCSKERNELDUMP ioctl to return ENXIO if the
interface was down, but it does not actually do this. Grab the link
status using getifaddrs(3) instead, and downgrade this case from an
error to a warning; the user might bring the link back up at a later
time.
Reviewed by: cem
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D35196
I pushed the last changes before I'd noticed the better wording
suggestions in the review. Also include a note that not all lines will
have a timestampe. Some multi-line messages are generated with sbuf, and
when those are pushed, only the first line will have the
timestamp. Document this quirky behavior as well since fixing it likely
won't happen soon. CAM periph drivers generate all the lines in their
announce message together so they aren't intermingled with other things,
for example.
Suggested by: allanjude, emaste, rpokala
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D35139
Differential Revision: https://reviews.freebsd.org/D35141
Today, kern.msgbuf_show_timestamp=1 will give 1 second granularity
timestamps on dmesg lines. When kern.msgbuf_show_timestamp=2, we'll
produce microsecond level graunlarity.
For example:
old (== 1):
[13] Dual Console: Video Primary, Serial Secondary
[14] lo0: link state changed to UP
[15] bxe0: NIC Link is Up, 10000 Mbps full duplex, Flow control: ON - receive & transmit
[15] bxe0: link state changed to UP
new (== 2):
[13.807015] Dual Console: Video Primary, Serial Secondary
[14.544150] lo0: link state changed to UP
[15.272044] bxe0: NIC Link is Up, 10000 Mbps full duplex, Flow control: ON - receive & transmit
[15.272052] bxe0: link state changed to UP
Sponsored by: Netflix
its attempt to install SA/SPD into the kernel results in cryptic
EINVAL error code.
Let it be a bit more user-friendly and try to load ipsec.ko
automatically if it is not loaded, just like ifconfig(8) does it
for modules it needs.
PR: 263379
MFC after: 2 weeks
The daemon can specify fsname=XXX in its mount options. If so, the file
system should report f_mntfromname as XXX during statfs. This will show
up in the output of commands like mount and df.
Submitted by: Ali Abdallah <ali.abdallah@suse.com>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D35090
AEAD ciphers for IPsec combine both encryption and authentication. As
such, ESP configurations using an AEAD cipher should not use a
seperate authentication algorithm via -A. However, this was not
apparent from the setkey manpage and 12.x and earlier did not perform
sufficient argument validation permitting users to pair an explicit -A
such as SHA256-HMAC with AES-GCM. (The result was a non-standard
combination of AES-CTR with the specified MAC, but with the wrong
initial block counter (and thus different keystream) compared to using
AES-CTR as the cipher.)
Attempt to clarify this in the manpage by explicitly calling out AEAD
ciphers (currently only AES-GCM) and noting that AEAD ciphers should
not use -A.
While here, explicitly note which authentication algorithms can be
used with esp vs esp-old. Also add subsection headings for the
different algorithm lists and tidy some language.
I did not convert the tables to column lists (Bl -column) though that
would probably be more correct than using literal blocks (Bd
-literal).
PR: 263379
Reviewed by: Pau Amma <pauamma@gundo.com>, markj
Differential Revision: https://reviews.freebsd.org/D34947
Similar to ipfw rule timestamps, these timestamps internally are
uint32_t snaps of the system time in seconds. The timestamp is CPU local
and updated each time a rule or a state associated with a rule or state
is matched.
Reviewed by: kp
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D34970
Since a16732d670 we always print the l3 src/destination for Ethernet
rules. Update the tests to account for this.
Sponsored by: Rubicon Communications, LLC ("Netgate")
While the kernel only performs the L3 check for
ETHERTYPE_IP/ETHERTYPE_IP6 we should always print the source and
destination addresses.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D34918
Allow tables to be used for the l3 source/destination matching.
This requires taking the PF_RULES read lock.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D34917
After this, we'll be able to ping a host and not spam the terminal, and
no flooding will have to be involved. I've been doing this under Linux
as ping -fi1 host.
Reviewed by: rpokala, Pau Amma
Differential Revision: https://reviews.freebsd.org/D34882
The new '-L' flag will cause savecore to invoke the new mem(4) kernel
dump ioctl, taking a dump of the running system and writing the result
to a temporary file. Validation of the dump header is performed, similar
to regular crash dumps, and the final result is written to
livecore.X[.zst|.gz].
Also added is the '-Z' flag, which instructs the kernel to compress the
livedump compressed with zstd, akin to the existing -z flag. This option
has no effect in normal savecore(8) operation, but in theory could be
extended to perform such compression while reading the dump from the
dump device.
Encryption is unsupported for live dumps.
For example: 'savecore -Lz /var/crash' would create:
/var/crash/livecore.0.gz
Reviewed by: markj
MFC after: 2 weeks
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D34347
Move it to a separate function, allowing its reuse.
Reviewed by: markj
MFC after: 3 days
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D34822
All files are now created relative to savedirfd, e.g. with openat(2).
Therefore, we do not need character buffers to be PATH_MAX bytes long,
just long enough to hold the complete filename. 32 bytes is long enough
in all cases. These can be allocated on the stack.
While here, fix an error message that attempts to use an uninitialized
infoname.
Reviewed by: markj
MFC after: 3 days
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D34821
So that new callers of getbounds() don't need to duplicate it.
Reviewed by: markj
MFC after: 3 days
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D34783
When asked to print rules recursively, correctly recurse for anchors
included in pf.conf with "anchorname/*".
PR: 262590
Reviewed by: kp
MFC after: 3 weeks
This fixes a performance problem where poudriere -j 104 keeps remounting
filesystems, which induce wanting to signal mountd, if running. The
current code tries to do it by creating the pidfile in /var/run and
unlinking it if the operation succeeds, inducing contention against
anything doing an exec as it tries to look up /var/run/ld-elf.so.hints
Differential Revision: https://reviews.freebsd.org/D34681
This check was previously in `create` only, not applying to renames. It
should really be applied at the libbe level, so that we can avoid
writing about this restriction over and over again.
While we're here: `bectl rename` always succeeds, even when it doesn't.
Start returning the error.
Reported By: Christian McDonald <cmcdonald netgate com>
Reviewed by: rew, jwmaag_gmail.com (earlier version)
Differential Revision: https://reviews.freebsd.org/D34605
Discuss the standard type of layout, as well as the "deep" BE layout,
and some of the properties of both. Point the various -r flags at this
new section, to help users understand which they're working with and
what the -r flag is actually doing. Note that we may just deprecate the
-r flag in future versions, but the flag will be recognized as a NOP at
that point.
Reviewed by: pauamma_gundo.com, rew
Differential Revision: https://reviews.freebsd.org/D34538
"ifconfig -g groupname" prints a list of interface names,
which could be confusing, because it differs from
the behavior of "ifconfig -a -g groupname".
While here, add two examples showing the difference between
"ifconfig -a -g groupname" and "ifconfig -g groupname".
Fixes: 0dad3f0e15 Import interface groups from OpenBSD.
MFC after: 2 weeks
This reference has been present in the manual page since the initial
import of BSD 4.4 Lite sbin Sources. It's time for it to be removed.
MFC after: 2 weeks
- Remove extraneous examples
- Apply "-compact" to the list macros so that it is possible to fit the
definitions of the types and formats in one terminal screen.
MFC after: 2 weeks
This change is about moving the -f documentation into the right place in
the manual. Also, document the IFCONFIG_FORMAT variable in the
ENVIRONMENT section.
MFC after: 2 weeks
In order to clean up the layout of the manual page, let's keep
parameters in the end of the DESCRIPTION section. This patch does not
change any content, it's meant to only move the content around before
refactoring.
MFC after: 2 weeks
- There is no need to mention in the synopsis that -f can be a list of
comma-separated type:format pairs. Let's keep it simple instead.
- Mention that -f can be supplied multiple times.
- Add -f to other entries in the synopsis where it can be used.
MFC after: 2 weeks
As documented, the -C flag can only be used on its own. Any other
command modifiers and flags are ignored when -C is used. Reflect that in
synopsis.
MFC after: 2 weeks
We document capability codes (the CAPS field of "ifconfig wlan0 scan")
in both ifconfig(8) and the handbook. The list is more complete in the
manual page, while the descriptions of individual capabilities are more
detailed in the handbook.
In order to reduce content duplication and bit rot, let's move
handbook's details to the manual page and reference the manual page
whenever necessary.
Reviewed by: debdrup
Reviewed by: Pau Amma
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D34662
Disallow the use of tables in ethernet rules. Using tables requires
taking the PF_RULES lock. Moreover, the current table code isn't ready
to deal with ethernet rules.
Disallow their use for now.
Sponsored by: Rubicon Communications, LLC ("Netgate")
When using the snapshot option, all other options are ignored. This
update reflects changes made in ab2dbd9b87.
Reviewed by: 0mp, mckusick
Differential Revision: https://reviews.freebsd.org/D34584
When retrieving nat rules in anchors we need to set the path just like
we do for regular rules.
MFC after: 1 week
Sponsored by: Rubicon Communications, LLC ("Netgate")
The -r flag is ignored by the FreeBSD implementation of bsdlabel(8)
(also called disklabel(8) in the past). Remove its use from examples
and tests in the tree.
This commit does not touch historical documentation under share/doc/smm
and files under contrib/netbsd-tests.
Reviewed by: imp
MFC after: 2 weeks
Approved by: imp (src)
Fixes: 57dfbec57b More axe-work:
Differential Revision: https://reviews.freebsd.org/D34585
for missing devices.
The fsck_ffs(8) utility uses its internal function openfilesys()
when opening a disk to be checked. This change avoids the use
of pfatal() in openfilesys() which always exits with failure (exit
value 8) so that the caller can choose the correct exit value.
In the case of a non-existent device it should exit with value 3
which allows the startup system to wait for drives (such as those
attached by USB) to come online.
Reported by: karels
Tested by: karels
PR: 262580
MFC after: 3 days
Allow filtering based on the source or destination IP/IPv6 address in
the Ethernet layer rules.
Reviewed by: pauamma_gundo.com (man), debdrup (man)
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D34482
FreeBSD 14.0 is going to ship with a new implementation of the mixer(8)
command. Unfortunately, in order to support new features like mute, the
command-line interface of the new implementation is not backwards
compatible.
Update all the remaining documentation and scripts in the src tree
to use the new syntax.
While here, document in usbhidaction.1 that the mute functionality is
now supported.
Reviewed by: christos, debdrup, hselasky
Approved by: hselasky (src)
Fixes: 903873ce15 Implement and use new mixer(3) library for FreeBSD.
Differential Revision: https://reviews.freebsd.org/D34545
Traditionally the GEOM's primary channel of information from kernel to
user-space was confxml, fetched by libgeom through kern.geom.confxml
sysctl. It is convenient and informative, representing full state of
GEOM in a single XML document. But problems start to arise on systems
with hundreds of disks, where the full confxml size reaches many
megabytes, taking significant time to first write it and then parse.
This patch introduces alternative solution, allowing to fetch much
smaller XML document, subset of the full confxml, limited to 64KB and
representing only one specified geom and optionally its parents. It
uses existing GEOM control interface, extended with new "getxml" verb.
In case of any error, such as the buffer overflow, it just transparently
falls back to traditional full confxml. This patch uses the new API in
user-space GEOM tools where it is possible.
Reviewed by: imp
MFC after: 2 month
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D34529
I see more user-friendly to do nothing if the module is already
loaded, rather than returning quite confusing error message.
As side effect it allows to avoid std_list_available() call, using
quite expensive on large systems geom_gettree().
MFC after: 1 month
Introduce pfctl_get_rules_info(), similar to pfctl_get_eth_rules_info()
to retrieve rules information (ticket and total number of rules).
Use the new function in pfctl.
MFC after: 1 week
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D34443
Make gctl_add_param() API public, allowing more precise control over
parameter flags. Previously it was impossible to properly declare
write-only ASCII parameters, used for result reporting, they were
declared as read-write binary instead, that was not nice.
MFC after: 1 month
When printing the interface name from the ipstate_t struct the interface
name in is_ifp may not always be avaiable when reading it from kmem
(tested on FreeBSD and NetBSD). However the is_ifname (the interface
name character string) is almost always available -- it is not available
when the source of the packet is a process running on the firewall
itself. Rather than print both interface name strings, print only the
one.
MFC after: 1 week
Rather than use a kmem read to determine the interface name used by a
nat_t structure through a pointer, nat_ipfs->netif->if_xname, obtain it
directly from nat_ifnames in the nat_t structure itself using the new
FORMAT_IF macro.
MFC after: 1 week
Interface names stored in the ipstate_t and ipnat_t structures can be
NULL. This occurs when an application, such as named, is running on the
firewall machine itself. For example an application, i.e. named, running
on the firewall itself will cause a state table display and NAT mapping
display to show a null ingress interface and its egress interface. This
is perfectly valid but confusing to human eyes. Rather than print
nothing, print "(null)".
MFC after: 1 week
Just as pfctl already does for other rules we print the ethernet rules
we would have loaded if '-n' is specified.
Sponsored by: Rubicon Communications, LLC ("Netgate")
When filtering Ethernet packets allow rules to specify a mac address
with a mask. This indicates which bits of the specified address are
significant. This allows users to do things like filter based on device
manufacturer.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Teach the 'ether' rules to accept { mac1, mac2, ... } lists, similar to
the lists of interfaces or IP addresses we already supported for layer 3
filtering.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D32481
Allow packets to be tagged with dummynet information. Note that we do
not apply dummynet shaping on the L2 traffic, but instead mark it for
dummynet processing in the L3 code. This is the same approach as we take
for ALTQ.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D32222
If we're not filtering on a specific MAC address don't print it at all,
rather than showing an all-zero address.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D31749
Allow the evaluations/packets/bytes counters on Ethernet rules to be
cleared.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D31748
Extent pfctl to be able to read configured Ethernet filtering rules from
the kernel and print them.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D31738
The gunion(8) utility is used to track changes to a read-only disk on
a writable disk. Logically, a writable disk is placed over a read-only
disk. Write requests are intercepted and stored on the writable
disk. Read requests are first checked to see if they have been
written on the top (writable disk) and if found are returned. If
they have not been written on the top disk, then they are read from
the lower disk.
The gunion(8) utility can be especially useful if you have a large
disk with a corrupted filesystem that you are unsure of how to
repair. You can use gunion(8) to place another disk over the corrupted
disk and then attempt to repair the filesystem. If the repair fails,
you can revert all the changes in the upper disk and be back to the
unchanged state of the lower disk thus allowing you to try another
approach to repairing it. If the repair is successful you can commit
all the writes recorded on the top disk to the lower disk.
Another use of the gunion(8) utility is to try out upgrades to your
system. Place the upper disk over the disk holding your filesystem
that is to be upgraded and then run the upgrade on it. If it works,
commit it; if it fails, revert the upgrade.
Further details can be found in the gunion(8) manual page.
Reviewed by: Chuck Silvers, kib (earlier version)
tested by: Peter Holm
Differential Revision: https://reviews.freebsd.org/D32697
NAT table mappings list only the source and destination IP, the source
and destinaion port numbers, and their mappings. But the protocol is not
listed. Now that Facebook and Google use QUIC, seeing port 443 in in a
list of active NAT sessions could mean 443/tcp or 443/udp. This patch
adds the protocol to the listing to aid in determining whether HTTPS is
TCP or QUIC in a NAT mapping listing. This also helps differentiatinete
between other protocols such as ICMP, ESP, and AH in ipnat list of active
sessions.
MFC after: 1 week
The cleanup of fsck_ffs(8) in commit c0bfa109b9 broke fsdb(8).
This commit adds the one-line update needed in fsdb(8) to make it
work with the new fsck_ffs(8) structure.
Reported by: Chuck Silvers
Tested by: Chuck Silvers
MFC after: 3 days
Minor improvements to the fwdownload code suggested by chs@:
o Print the path_id/target we're rescanning so it's not invisible
o No need for XPT_GDEVLIST, all the info is filled in. Remove sending it
as well as a comment related to it from a mistaken observation. libcam
always fills these in properly, so use those for the ccb path/target.
o Don't leak /dev/xpt fd in success cases.
o Rename fw_rescan_lun to fw_rescan_target and pass sim_mode to
only print path_id and target_id info.
Reviewed by: chs@
Fixes: 9835900cb9
Sponsored by: Netflix
MFC After: 1 week
Differential Revision: https://reviews.freebsd.org/D34348
After downloading the firmware to a device, it's inquiry data likely
will change. Force a rescan of the target with the CAM_EXPECT_INQ_CHANGE
flag to get it to record the new inqury data as being expected. This
avoids the need for a 'camcontrol rescan' on the device which detaches
and re-attaches the disk (da, ada) device. This brings fwdownload up to
nvmecontrol's ability to do the same thing w/o changing the exposed
nvme/nvd/nda device. We scan the target and not the LUN because dual
actuator drives have multiple LUNs, but the firmware is global across
many vendors' drives (and the so far theoretical ones that aren't won't
be harmed by the rescan).
Since the underlying struct disk is now preserved accross this
operation, it's now possible to upgrade firmware of a root device w/o
crashing the system. On systems that are quite busy, the worst that
happens is that certain operaions are reported cancelled when the new
firmware is activated. These operations are retried with the normal CAM
recovery mechanisms and will work on the retry. The only visible hiccup
is the time that new firmware is flashing / initializing. One should not
consider this operation completely risk free, however, since not all
drives are well behaved after a firmware download.
MFC After: 1 week
Relnotes: yes
Sponsored by: Netflix
Feedback by: mav
Differential Revision: https://reviews.freebsd.org/D34325
Add boottrace annotations to record events in init(8), shutdown(8), and
reboot(8).
Sponsored by: NetApp, Inc.
Sponsored by: Klara, Inc.
X-NetApp-PR: #23
Differential Revision: https://reviews.freebsd.org/D31928
Normally fsck_ffs never does reads or writes that are not aligned
to the size of one of the checked filesystems fragments. The one
exception is when it finds that it needs to write the superblock
recovery information. Here it will write with the alignment reported
by the underlying disk as its sector size as reported by an
ioctl(diskfd, DIOCGSECTORSIZE, &secsize).
Modern disks have a sector size of 4096, but for backward compatibility
with older disks will report that they have a sector size of 512.
When presented with a 512 byte write, they have to read the associated
4096 byte sector, replace the 512 bytes to be written, and write
the updated 4096 byte sector back to the disk. Unfortunately, some
disks report that they have 512 sectors, but fail writes that are not
aligned to 4096 boundaries and are a multiple of 4096 bytes in size.
This commit updates fsck_ffs(8) so that it uses the filesystem fragment
size as the smallest size and alignment for doing writes rather than
the disk's reported sector size.
Reported by: Andriy Gapon
MFC after: 1 week
NetBSD has an ATF test for newfs_msdos. Connect it to the build.
Adapt it for FreeBSD. This would have caught the bug fixed by my
previous commit.
Reviewed by: delphij, emaste
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D34116
The type of the kern.maxphys sysctl OID is now ulong. Change the
local variable type to match.
Reviewed by: delphij, emaste
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D34116
VLAN ID 0 is supposed to be interpreted as having no VLAN with a bit of
priority on the side, but the kernel is not able to decapsulate this on
the fly so dhclient needs to take care of it.
Reviewed by: markj
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D31515
Since 59f256ec35 dmesg(8) will always skip first line of the message
buffer, cause it might be incomplete. The problem is that in most cases
it is complete, valid and contains the "---<<BOOT>>---" marker. This
skip can be disabled with '-a', but that would also unhide all non-kernel
messages. Move this functionality from dmesg(8) to kernel, since kernel
actually knows if wrap has happened or not.
The main motivation for the change is not actually the value of the
"---<<BOOT>>---" marker. The problem breaks unit tests, that clear
message buffer, perform a test and then check the message buffer for
a result. Example of such test is sys/kern/sonewconn_overflow.
Part of the problem was that fsck_ffs would read the superblock
multiple times complaining and repairing the superblock check hash
each time and then at the end failing to write out the superblock
with the corrected check hash. This fix reads the superblock just
once and if the check hash is corrected ensures that the fixed
superblock gets written.
Tested by: Peter Holm
PR: 245916
MFC after: 1 week
Sponsored by: Netflix
We provide the hostid (which is the state creatorid) to the kernel as a
big endian number (see pfctl/pfctl.c pfctl_set_hostid()), so convert it
back to system endianness when we get it from the kernel.
This avoids a confusing mismatch between the value the user configures
and the value displayed in the state.
MFC after: 3 weeks
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D33989
If an invalid (i.e. overly long) interface name is specified error out
immediately, rather than in expand_rule() so we point at the incorrect
line.
PR: 260958
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D34008
The "bg" option does not go background until the initial mount
attempt fails, which can take 60+ seconds.
This new "bgnow" option goes background immediately, avoiding
the 60+ second delay, if the NFS server is not yet available.
The man page update is a content change.
Tested by: jwb
Reviewed by: debdrup, emaste
PR: 260764
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D33733
Those can be returned by CHECK POWER MODE command (0xe5).
Note that some of the definitions duplicate definitions for Extended
Power Conditions.
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D33646
We don't really use the scsi regexp for anything. The rescan was a
workaround that was fixed a long time ago and has been disabled for
ages. And the regexp was incomplete.
Sponsored by: Netflix
_PATH_LD32_HINTS is unused because it is a.out remnant.
_PATH_ELF32_HINTS is provided by rtld_paths.h already.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
ipfsync is a WIP sync daemon designed to be used in a failover scenario.
It was removed by 5ee61c7daa. This commit
restores its three files. ipfsync is in my work queue.
MFC after: 10 days
X-MFC with: 5ee61c7daa
Under some INET/INET6 src.conf configurations sbin/route previously
failed to build due to an unused variable warning. It was functionally
write-only anyway, so just remove it.
Reported by: melifaro
Reviewed by: melifaro
MFC after: 3 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D33717
The function makevfslist is only called once in mount.c, but should
be save to be called more than once with different parameters.
The bin/df command links against this file, and will need this
possibility to allow -l and -t to be used together.
MFC after: 3 days
The work to ANSIfy and adjust returns to style(9) resulted in a mismerge
of a stash when ipfilter was moved from contrib to sbin. An older file
replaced WIP at the time, resulting in a regression.
The majority of this work was done in 2018 saved as git stashes within
a git-svn tree and migrated to the git tree. The regression occurred
when the various stashes were sequentially merged to create individual
commits, following the ipfilter move to netpfil and sbin.
Reported by: jrtc27
Fixes: 2582ae5740
Pointy hat to: cy
MFC after: 1 month
Replace the INLINE macro with inline. Some ancient compilers supported
__inline__ instead of inline. The INLINE hack compensated for it.
Ancient compilers are history.
Reported by: glebius
MFC after: 1 month
Convert ipfilter userland function declarations from K&R to ANSI. This
syncs our function declarations with NetBSD hg commit 75edcd7552a0
(apply our changes). Though not copied from NetBSD, this change was
partially inspired by NetBSD's work and inspired by style(9).
Reviewed by: glebius (for #network)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D33595
Extend the dnctl (dummynet config) tool to be able to read commands from
a file, just like ipfw already does.
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D33627
Shortlinks occupy the space of both di_db and di_ib when used. However,
everywhere that wants to read or write a shortlink takes a pointer do
di_db and promptly runs off the end of it into di_ib. This is fine on
most architectures, if a little dodgy. However, on CHERI, the compiler
can optionally restrict the bounds on pointers to subobjects to just
that subobject, in order to mitigate intra-object buffer overflows, and
this is enabled in CheriBSD's pure-capability kernels.
Instead, clean this up by inserting a union such that a new di_shortlink
can be added with the right size and element type, avoiding the need to
cast and allowing the use of the DIP macro to access the field. This
also mirrors how the ext2fs code implements extents support, with the
exact same structure other than having a uint32_t i_data[] instead of a
char di_shortlink[].
Reviewed by: mckusick, jhb
Differential Revision: https://reviews.freebsd.org/D33650
Move some needed binaries/libs from FreeBSD-utilities to FreeBSD_runtime.
This is everything needed to boot to multiuser with FreeBSD-rc installed.
MFC after: 2 weeks
Sponsored by: Beckhoff Automation GmbH & Co. KG
Differential Revision: https://reviews.freebsd.org/D33435
Through fixes and improvements our ipfilter sources have diverged
enough to warrant move from contrib into sbin/ipf. Now that I'm
planning on implementing MSS clamping as in iptables it makes more
sense to move ipfilter to sbin.
This is the second of three commits of the ipfilter move.
Suggested by glebius on two occaions.
Suggested by and discussed with: glebius
Reviewed by: glebius, kp (for #network)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D33510
Through fixes and improvements our ipfilter sources have diverged
enough to warrant move from contrib into sys/netpil. Now that I'm
planning on implementing MSS clamping as in iptables it makes more
sense to move ipfilter to netpfil.
This is the first of three commits the ipfilter move.
Suggested by glebius on two occaions.
Suggested by and discussed with: glebius
Reviewed by: glebius, kp (for #network)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D33510