Commit Graph

204 Commits

Author SHA1 Message Date
Bill Paul
96fd5c300d Add support for the 8139C+ chipset. Unlike the other chips in the 8139
series, the 8139C+ has a descriptor-based DMA mechanism, and its
performance is actually pretty respectable. Note: the 8139D chip does
not support C+ mode. Only the 8139C+ and 8169 gigE chips support C+ mode.

Supported features:

- RX and TX checksum offload
- hardware VLAN tag insertion/extraction
- TX interrupt moderation using the 8139's on-board timer

Everything should be properly busdma'ed and endian-independent, so
things should work ok on non-x86 platforms. Unfortunately, my call
for testers on this code was met with deafening silence, and I don't
have access to any non-x86 FreeBSD boxes at the moment, so this is
speculation.

The device detection code has been cleaned up a little as well
(thanks to Michal Mertl) for the patches.

There are also updates to the rl(4) man page (which I accidentally
checked in before when I updated the dc(4) man page. Oops.)

Todo: finish support for the 8169 gigabit ethernet chip. This
mainly requires writing an rlgphy driver to handle the 8169's built-in
PHY. This will have to wait until I actually get my hands on an 8169
card for testing though. (I still can't find a source for one in the
U.S. Suggestions/pointers welcome.)
2003-07-10 20:38:48 +00:00
Warner Losh
b84e866a18 Due to extreme bogusness in the pci bus layer, these drivers were
forced to do slightly bogus power state manipulation.  However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...

This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
2003-07-03 21:39:53 +00:00
Scott Long
f6b1c44d1f Mega busdma API commit.
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma.  At the moment, this is used for the
asynchronous busdma_swi and callback mechanism.  Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg.  dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create().  The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.

sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms.  The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.

If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.

Reviewed by:	tmm, gibbs
2003-07-01 15:52:06 +00:00
Bill Paul
2e7c2f97aa In order to set the MAC address on RealTek NICs, you must flip WRITECFG
bit in the EEPROM mode register on. Also, the address must be written
in two 32-bit register accesses instead of 6 8-bit accesses.

Tested with my 8139B cardbus NIC.

PR:	kern/35900
Submitted by:	Mark Kettenis <kettenis@chello.nl>
2003-06-29 17:33:33 +00:00
David E. O'Brien
f4636c5959 Use __FBSDID(). 2003-06-11 06:34:30 +00:00
Poul-Henning Kamp
674ebf0f6b Remove break after return;
Found by:       FlexeLint
2003-05-31 20:01:14 +00:00
Warner Losh
214073e5e4 Use newly minted device_is_attached rather than device_is_alive to see
if attach succeeded.  device_is_alive just tells us that probe
succeeded.  Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.

Symptoms of problem reported by: martin blapp
2003-04-21 18:34:04 +00:00
Nate Lawson
693f4477b1 Revise attach/detach resource cleanup
- Unconditionally call *_stop() if device is in the tree. This is to
  prevent callouts from happening after the device is gone. Checks for
  bus_child_present() should be added in the future to keep from touching
  potentially non-existent hardware in *_detach().  Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
  the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
  that ifmedia_removeall() can be unconditionally called on detach. There
  is no way to detect whether ifmedia has been initialized without using
  a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
Matthew N. Dodd
533294b956 - Don't call pci_enable_io() in drivers (unless needed for resume).
- Don't test memory/port status and emit an error message; the PCI
  bus code will do this now.
2003-04-16 03:16:57 +00:00
Matthew N. Dodd
f246e4a17f - Express hard dependencies on bus (pci, isa, pccard) and
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
  such abuse isn't really needed.  (And if we do need type information
  associated with a module then we should make it explicit and not
  use hacks.)
2003-04-15 06:37:30 +00:00
Mike Silbersack
75d8feb42a Rework the rl_encap failure case. Previously, we would stuff the
unencapsulated packet back into the IFQ.  Unfortunately, the only reason
rl_encap would fail was due to m_defrag failing, which should only happen
when we're low on mbufs.  Hence, it was possible for us to end up with
an IFQ full of packets which could never clear the queue because they could
never be defragmented because they were themselves taking up all the mbufs.

To solve this, take if_xl's approach to the problem of encapsulation failure:
drop the packet.

MFC after:	3 days
2003-04-15 04:06:01 +00:00
Mike Silbersack
2590e88477 Quick fix so that the watchdog timer is not set unless packets are
actually queued for transmission.  Without this, a low memory situation
would trigger false watchdog timeouts.

MFC after:	1 week
2003-04-08 03:32:52 +00:00
John Baldwin
59f47d29b7 Add missing ()'s so that these drivers all compile again.
Noticed by:	jake
Tested on:	i386 (compile)
2003-03-31 20:22:00 +00:00
Nate Lawson
54f1f1d1e6 Clean up locking and resource management for pci/if_*
- Remove locking of the softc in the attach method, instead depending on
  bus_setup_intr being at the end of attach (delaying interrupt enable until
  after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
  in detach to only free resources that were allocated.  This puts all
  resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
  be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before.  It was unnecessary
  to move it.  This reverts part of 1.88
- rl: move irq allocation before ether_ifattach.  Problems might have been
  caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
  null pointer.

Reviewed by:	imp, mdodd
2003-03-31 17:29:43 +00:00
Mike Silbersack
709b85c372 Switch rl_encap over to using m_defrag.
No functional change, the previous rl_encap was correct wrt long
mbuf chains; this just reduces code duplication.

MFC after:	2 weeks
2003-03-30 03:45:28 +00:00
MIHIRA Sanpei Yoshiro
1017eea32d Add support for Planex FNW-3800-TX(CardBus 100M/10M).
Submitted by:	Kunihiro Arai <araik@attglobal.net>
Obtained from:	[bsd-nomads:16625]
2003-03-18 14:57:09 +00:00
Dan Moschuk
25b803ef49 Add support for Peppercon ROL-F Card.
Submitted by: Sascha Holzeiter <sascha@root-login.org>
PR: 48559
2003-02-23 23:35:35 +00:00
Warner Losh
a163d034fa Back out M_* changes, per decision of the TRB.
Approved by: trb
2003-02-19 05:47:46 +00:00
Nate Lawson
3f54508cba Clean up exit path from rl_attach() to remove multiple returns 2003-02-09 22:32:50 +00:00
Alfred Perlstein
44956c9863 Remove M_TRYWAIT/M_WAITOK/M_WAIT. Callers should use 0.
Merge M_NOWAIT/M_DONTWAIT into a single flag M_NOWAIT.
2003-01-21 08:56:16 +00:00
Dag-Erling Smørgrav
9af714a731 FBSDIDize and clean up whitespace nits. 2003-01-11 16:11:21 +00:00
Dag-Erling Smørgrav
f4be139a67 Read sanpei's mind, and unbreak the build. 2003-01-11 16:08:59 +00:00
MIHIRA Sanpei Yoshiro
fe41c67cfc Add support for Corega FEtherII CB-TXD (CardBus 100M/10M).
Fix typo (Coreaga->Corega)
2003-01-11 07:10:35 +00:00
Martin Blapp
e808cf6260 When reading PHY regs over the i2c bus, the turnaround ACK bit
is read one clock edge too late. This bit is driven low by
slave (as any other input data bits from slave) when the clock
is LOW. The current code did read the bit after the clock was
driven high again.

Reviewed by:	luoqi
MFC after:	2 weeks
2003-01-10 08:09:58 +00:00
Jake Burkholder
69a0015af3 Tweaks to make if_rl work on sparc64.
Mostly submitted by:	tmm
Tested on:		i386, sparc64
2003-01-05 21:36:59 +00:00
Sam Leffler
9ef8b52020 o track either_ifattach/ether_ifdetach API changes
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes

Reviewed by:	many
Approved by:	re
2002-11-14 23:49:09 +00:00
Warner Losh
16093e3f47 Don't take out the rl_mtx lock in the attach routine. The only way
we'd need it is if we're interrupted.  So, register the interrupt last
in the attach routine.
2002-10-29 19:02:19 +00:00
Poul-Henning Kamp
88647b6de5 Be consistent about functions being static.
Properly put macro args in ().

Spotted by:	FlexeLint.
2002-10-16 09:14:59 +00:00
Poul-Henning Kamp
1878960dc9 Fix two misindents.
Spotted by:	FlexeLint
2002-10-01 22:27:03 +00:00
Mitsuru IWASAKI
efd1491c3f Add support for Corega FEther CB-TXD (CardBus 100M/10M). 2002-09-06 16:38:06 +00:00
Alfred Perlstein
e3d2833a26 style:
put return values on a line by themselves.
 fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
Maxim Sobolev
62f7648682 Increase size of ifnet.if_flags from 16 bits (short) to 32 bits (int). To avoid
breaking application ABI use unused ifreq.ifru_flags[1] for upper 16 bits in
SIOCSIFFLAGS and SIOCGIFFLAGS ioctl's.

Reviewed by:	-hackers, -net
2002-08-18 07:05:00 +00:00
John Baldwin
c038666eae If we get 0xffff back when reading the status register, assume the card
has gone away instead of spinning in the interrupt handler.  This stops
my machine from hanging when I eject a rl(4)-based cardbus card.

Reviewed by:	imp
2002-07-30 17:31:42 +00:00
Luigi Rizzo
2e4fb41fa5 Fix if_timer logic to make sure that there is always a timeout
pending if there are packets queued for transmission.

Several drivers still have the same problem.

MFC after: 3 days
2002-06-30 22:16:22 +00:00
John Baldwin
d204693572 Add support for the D-Link DFE-690TXD Cardbus card which has a RealTek 8139
with its own PCI ID.
2002-05-06 13:43:00 +00:00
Luigi Rizzo
7632341a30 Add DEVICE_POLLING support to the "rl" driver.
The diffs are very similar to the ones for the "sis" driver.

MFC After: 5 days
2002-04-16 22:03:14 +00:00
Bill Paul
9a29439fb9 Nortel Networks sells a RealTek 8139-based NIC that's basically
the same thing as the SMC 1211, but with their own vendor ID.
Update the device list to support this NIC. (Discovered these
cards lying around the lab at work.)
2002-04-11 06:12:51 +00:00
Bill Paul
a72c060fb0 Teach the rlphy driver how to do parallel link detection. If the link partner
doesn't support NWAY, the RealTek PHY (both the integrated ones on 8139
chips and the RTL8201L 10/100 PHY) will not report the link speed via
the ANLPAR or BMSR registers. For the 8201L, we need to look in magic
vendor-specific PHY register 0x19. For the 8139 MAC+PHY combo, we have
to be able to test the RL_MEDIASTAT register.

The changes to rlphy.c are based largely on the patch from PR 30836,
however I tried to eliminate some magic numbers by creating an entry
for the 8201 PHY in miidevs.

Also updated if_rl.c to allow the rlphy driver to read the RL_MEDIASTAT
register via the rl_miibus_readreg() routine.
2002-04-07 20:55:50 +00:00
John Baldwin
6008862bc2 Change callers of mtx_init() to pass in an appropriate lock type name. In
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.

Tested on:	i386, alpha, sparc64
2002-04-04 21:03:38 +00:00
Alfred Perlstein
e51a25f850 Remove __P. 2002-03-20 02:08:01 +00:00
Mike Silbersack
27d5f39f68 Remove mbuf exhaustion warning messages; these are handled by the
mbuf system in a rate-limited fashion now.

MFC after:	3 days
2002-02-11 23:38:30 +00:00
Luigi Rizzo
268cc03905 Remove printf's on mbuf/cluster allocation failures. There are now
equivalent and less dangerous (rate limited) messages in
the mbuf allocation code.

MFC after: 3 days
2001-12-14 05:56:35 +00:00
Mitsuru IWASAKI
0c66d318dd Add suspend/resume code mostly merged from fxp driver. 2001-11-23 14:27:33 +00:00
Bill Paul
0219a42155 Convert the if_sis and if_rl drivers to use the bus_dma API instead of
calling vtophys() and contigmalloc()/contigfree() directly. Hopefully,
I have shaken out all of the problems with busdma on the alpha now.
(Everything seems to work as expected.)

Also, change the max RX DMA limit to 1024 bytes instead of "unlimited,"
as the latter seems not to work correctly on the alpha that I tested.
(At 100Mbps, all attempts to receive frames yield RX errors.)
2001-08-15 17:38:43 +00:00
Bill Paul
75ff968cd5 Apply patch supplied by Jonathan Chen: use the correct arguments to
pci_enable_io(). We need to use SYS_RES_IOPORT/SYS_RES_MEMORY instead
of PCIM_CMD_PORTEN/PCIM_CMD_MEMEN.
2001-07-09 17:58:42 +00:00
Bosko Milekic
f5eece3fb9 Change m_devget()'s outdated and unused `offset' argument to actually mean
something: offset into the first mbuf of the target chain before copying
the source data over.

Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).

The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.

Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
2001-06-20 19:48:35 +00:00
Bill Paul
07f65363cd Big round of minor updates:
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
  that need them so we don't have to fiddle with the PCI power management
  registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
  PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
  a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
  mode in sis_reset(). This apparently fixes a problem on some
  motherboards where the DP83815 chip fails to receive packets.
  (Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
2001-02-21 20:54:22 +00:00
Jeroen Ruigrok van der Werven
d7d97eb0aa Preceed/preceeding are not english words. Use precede and preceding. 2001-02-18 10:43:53 +00:00
Poul-Henning Kamp
6817526d14 Convert if_multiaddrs from LIST to TAILQ so that it can be traversed
backwards in the three drivers which want to do that.

Reviewed by:    mikeh
2001-02-06 10:12:15 +00:00
Poul-Henning Kamp
78d82c8c59 Use LIST_FOREACH() to traverse ifp->if_multiaddrs list, instead of
<sys/queue.h> implementation details.

Created with:   /usr/sbin/sed
Reviewed with:  /sbin/md5
2001-02-03 16:29:10 +00:00
Bosko Milekic
08812b3925 Implement MTX_RECURSE flag for mtx_init().
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.

The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.

The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.

Reviewed by: jhb
2001-01-19 01:59:14 +00:00
Bill Paul
14a00c6c68 Use pci_get_powerstate()/pci_set_powerstate() which now exists in the
PCI code. This saves each driver from having to grovel around looking
for the right registers to twiddle.

I should eventually convert the other PCI drivers to do this; for now,
these three are ones which I know need power state handling.
2000-12-18 21:53:05 +00:00
Bill Paul
031fc810ab Initialize/grab the mutex earlier in the attach phase, so that
bailing out to the fail: label where we release/destroy the mutex
will work without exploding.
2000-12-04 22:46:50 +00:00
Roger Hardiman
0eaa901ba7 Print a warning when we detect a Realtek 8139B chip
(identified by the IO map being 256 bytes long instead of 128)

This chip works very unreliably on my Lanner embedded PC with the rl driver.
Lots of watchdog timeouts or poor performance.

Forcing the media type to 10 Meg (ifconfig rl0 media 10baseT/UTP) is a good
workaround.

This looks very similar to the problem reported in PR kern/18790

It is interesting to note that the linux driver has lots of special
case code for this chip.
2000-11-24 17:36:07 +00:00
Bill Paul
57c19b2049 Fix 8-bit EEPROM breakage: compare against 0x8129, not 8129. 2000-11-01 23:56:46 +00:00
Bill Paul
78d2de28df Fix support for cardbus cards:
- Add DRIVER_MODULE() declaration to make this driver a
	  child of cardbus
	- Handle different width EEPROMs

The CIS parser still barfs when scanning this card, but it seems to
probe/attach correctly anyway. I can't do a traffic test just yet
since I don't have a proper crossover cable handy.
2000-10-30 07:54:38 +00:00
Bill Paul
1d5e53109c Add PCI IDs for some additional cardbus cards. Yes, there really is
a RealTek 8139 cardbus device. Unfortunately it doesn't quite work yet
because the CIS parser barfs on it.

Submitted by msmith, with some small tweaks by me.
2000-10-28 09:00:20 +00:00
Poul-Henning Kamp
db7e3af111 Remove unneeded #include <machine/clock.h> 2000-10-15 14:19:01 +00:00
Bill Paul
1e856a7b34 Use device_get_nameunit(dev) as the mutex string when calling
mtx_init() instead of hard-coded string constant. Also remember to do
the mutex changes to the ste driver, which I forgot in the first commit.
2000-10-13 18:35:49 +00:00
Bill Paul
d1ce910572 First round of converting network drivers from spls to mutexes. This
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
2000-10-13 17:54:19 +00:00
Archie Cobbs
21b8ebd926 Make all Ethernet drivers attach using ether_ifattach() and detach using
ether_ifdetach().

The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.

Reviewed by:	julian, freebsd-net
2000-07-13 22:54:34 +00:00
Peter Wemm
86b0a953e2 Use the correct register name. s/PCI_COMMAND_STATUS_REG/PCIR_COMMAND/ 2000-05-28 16:13:43 +00:00
Archie Cobbs
2e2de7f23f Move code to handle BPF and bridging for incoming Ethernet packets out
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.

The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.

The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.

Reviewed by:	freebsd-net
2000-05-14 02:18:43 +00:00
Bill Paul
af020b6e13 Apply patch to rl_rxeof() to really enforce payload alignment in
the case where we receive a packet that wraps from the end of the
RX buffer back to the start. This fixes an unaligned access trap on
the alpha with NFS.
2000-05-05 12:47:47 +00:00
Peter Wemm
95a1645553 Depend on miibus.
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point.  if_aue does
strictly depend on miibus as it will fail to link if it is missing.
2000-04-29 13:41:57 +00:00
Bill Paul
7cfa339426 Two fixes for the RealTek:
- Only call m_pullup() when necessary.

- Check return value from rl_encap() in rl_start() to avoid panic when
  we run out of mbufs. (Fixes PR kern/17582)

PR:		kern/17582
2000-03-29 20:06:15 +00:00
Bill Fumerola
ecfa9802f0 Fix a small typo in the comments. 1999-12-28 06:04:29 +00:00
Bill Paul
9d378ed009 Fix problem reported by Matt Dillon. Occasionally, very small received
frames would be handled incorrectly due to bad usage of m_pullup() in
the case where the frame wraps from the end of the receive buffer back
the beginning.

Also, when manually extending small packets to pad them to the minimum
frame length during transmission, zero out the pad area to make some
really paranoid people happy.
1999-12-23 19:05:58 +00:00
Bill Paul
eb86c09749 Fix usage of m_pullup(). 1999-11-16 15:34:52 +00:00
Bill Paul
11ad85d1f5 Make some tweaks to the RealTek driver:
- Fix a bug in rl_rxeof() handler: in the case where the packet wraps
  from the end of the receive buffer back to the beginning, we need to
  insure that at least sizeof(ether_header) bytes make it into the first
  mbuf. If we don't, then doing eh = mtod(m, struct ether_header *)
  loses. To avoid this, we use m_pullup() to suck at least MHLEN -
  RL_ETHER_ALIGN bytes into the first mbuf, which should also help
  small packets fit into a single mbuf.

  Pointed out by: Philip A. Prindeville <philipp@zembu.com>

- Make the transmit threshold autotuning: start off with a small value
  and jack it up when TX underruns are detected.

- Also improve TX error recovery: kick the chip in the head with a
  reset/init sequence to make sure it recovers afer a transmit error.
1999-10-21 19:42:03 +00:00
Bill Paul
784733e9ec Change contigmalloc() lower memory bound from 1MB to 0 to improve
chances of allocations succeeding on systems with small amounts of
RAM.

Pointed out by: bde
1999-09-25 17:29:02 +00:00
Bill Paul
98a229f65e As suggested by phk, unconditionalize BPF support in these drivers. Since
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
1999-09-23 03:32:57 +00:00
Bill Paul
9e4c647c74 Tweak these for what I hope is the last time: change the DRIVER_MODULE()
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."

This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
1999-09-22 06:08:11 +00:00
Bill Paul
0355003f26 Un-do the changes to the DRIVER_MODULE() declarations in these drivers.
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:

- If you change the name in both places, then the kernel thinks that
  the device's name is now "if_foo", so you get things like:

if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo

  This is bogus. Now the device name doesn't agree with the logical
  interface name. There's no reason for this, and it violates the
  principle of least astonishment.

- If you leave the name in the driver_t struct as "foo" and only
  change the names in the DRIVER_MODULE() declaration to "if_foo" then
  attaching drivers to child devices doesn't work because the names don't
  agree. This breaks miibus: drivers that need to have miibuses and PHY
  drivers attached never get them.

In other words: damned if you do, damned if you don't.

This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
1999-09-20 19:06:45 +00:00
Bill Paul
fac1f39b19 Grrr. Okay, changing the devnames was a bad idea. Put them back the way
they were.
1999-09-20 08:47:11 +00:00
Bill Paul
b95a9362a0 Fix the strings in the driver_t structs so that they match the new names
in the DRIVER_MODULES() declarations. *sigh*
1999-09-20 08:14:39 +00:00
David E. O'Brien
abad681b03 Goofed and didn't change the second DRIVER_MODULE() linking these with
the miibus.

Noticed by:	wpaul
1999-09-20 07:50:10 +00:00
David E. O'Brien
bd8a15ce8a Change the name we register with DRIVER_MODULE() to include the leading
"if_".

Reviewed by:	msmith, wpaul
1999-09-20 06:50:52 +00:00
Peter Wemm
518dee7dbb Add a pointer to "controller miibus0" for people who will not read the
commit messages or GENERIC and insist on running -CURRENT.
It probably won't work, but it's worth a try.
1999-09-08 15:01:58 +00:00
Bill Paul
59519ca74f Convert the RealTek 8139 driver to newbus and miibus in one swell foop.
Also set it up to be compiled as a module.
1999-08-31 14:45:51 +00:00
Bruce Evans
3de9d6fbe4 Don't restrict our requests for contiguous memory to addresses >= 1MB.
This fixes, at least, panics in ncr_attach() on i386's with about 5MB
of memory.  The restriction was a hack to leave some low memory for ISA
DMA, but on i386's we now allocate pages from the top down, so all the
restriction did was cause our allocations to fail when there is no free
memory above 1MB.
1999-08-29 09:03:58 +00:00
Peter Wemm
c3aac50f28 $Id$ -> $FreeBSD$ 1999-08-28 01:08:13 +00:00
Mike Smith
3ed7a59b07 Clean up after removing sys/eventhandler.h from sys/systm.h at the last
minute.  This should cover all of the missed cases (and should let LINT
build again).
1999-08-21 22:10:49 +00:00
Mike Smith
fcb893a801 Implement a new generic mechanism for attaching handler functions to
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.

Retire the at_shutdown family of functions and replace them with
new event handler lists.

Rework kern_shutdown.c to take greater advantage of the use of event
handlers.

Reviewed by:	green
1999-08-21 06:24:40 +00:00
Bill Paul
7ad5b08ab3 Remove the definitions for the SiS 900 chip. This is not a RealTek
clone after all. I have the datasheets for this part; hopefully I can
write a proper driver soon.
1999-07-22 20:56:49 +00:00
Dag-Erling Smørgrav
6b5ca0d83e Rename bpfilter to bpf. 1999-07-06 19:23:32 +00:00
Peter Wemm
820f359d7e Change the cast in pci_map_port() from u_short * to pci_port_t * so it
compiles cleanly on the Alpha.  (On the alpha, the port type is an int,
not a short).
Cast a couple of pointers to ints via 'uintptr_t' rather than 'unsigned
int' since uintptr_t is long (64 bit) on Alpha, as are pointers.
1999-07-02 04:17:16 +00:00
Bill Paul
19e7516669 Fix up the RealTek 8139 driver to work on FreeBSD/alpha. This involves a
few changes:

- there was a bug in rl_list_tx_init(): it was calculating the registers
  to initialize incorrectly. Not a problem on the x86 where unaligned
  access are allowed, but a problem on the alpha.

- set rl_btag accordingly depending on the machine type

- rl_rxeof() needs to be sure to longword-align the packet data. This
  is a little tricky since we copy the data out of the receive buffer
  using m_devget(), however there's no way to tell m_devget() to fill
  in the mbufs starting at a particular offset. To get around this,
  we tell m_devget to copy bytes+2 bytes starting at offset offset-2. This
  results in the proper alignment, and we can trim off the two leading
  bytes afterwards with m_adj(). We also allocate some extra space before
  the start of the receive buffer so that we don't get into trouble in
  the case where offset == 0.

- redefine vtophys() in if_rlreg.h for the alpha.

Making this chipset work on the alpha is sort of the inverse of putting
a jet engine on a rowboat (putting a propeller on a 747?) but when
you can get these things for $5 a pop, it's hard to stop people from
buying them.
1999-06-19 20:17:38 +00:00
Bill Paul
c008dec8df Add support for SiS 900 chipset (PCI ID 0x1039/0x0900), which appears to
be yet another rebadged RealTek 8139.
1999-05-30 18:55:20 +00:00
Peter Wemm
579f45fa60 Simplify the COMPAT_PCI_DRIVER/DATA_SET hack. We can add:
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it.  Driver writers can do
this if it's not defined.  (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
1999-05-09 17:07:30 +00:00
Peter Wemm
96b3554e5c Use COMPAT_PCI_DRIVER() for registration if it exists. This shouldn't
hurt the driver portability to 3.x too much for where drivers are shared.
1999-04-24 20:17:05 +00:00
Bill Paul
ea716519f5 Merge in some updates for the RealTek driver, mainly:
- Rewrite the transmit section to be a little less bogus.
- Set ifq_maxlen correctly. RL_TX_LIST_CNT - 1 is wrong, because for the
  RealTek, RL_TX_LIST_CNT is 4. Set it to IFQ_MAXLEN instead.
1999-04-12 21:37:00 +00:00
Bill Paul
141ae16656 Add support for still more cheapo 10/100 cards: Delta Electronics and
Addtron appear to have their own VIA Rhine II and RealTek 8139 boards
with custom PCI vendor and device IDs. This commit updates the PCI
vendor and device lists in the vr and rl drivers so that we can probe
the additional devices.

Found by: nosing around the PCI vendor and device code list at:
	http://www.halcyon.com/scripts/jboemler/pci/pcicode
1999-02-23 15:38:25 +00:00
Bill Paul
e8354668bd Remember to initialize ifp->if_snd.ifq_maxlen. 1999-02-01 21:25:52 +00:00
Bill Paul
2008c8087c Multicast code isn't quite correct. The RealTek wants the upper six bits
of the CRC as the multicast hash table bit, not the lower six bits. Plus
we have to flip on all bits in the table for multicast mode.

Pointed out by: Kazushi SUGYO <k-sugyou@nwsl.mesh.ad.jp>
1999-01-22 15:25:04 +00:00
Bill Paul
d4a2465595 Small cosmetic tweak: in rl_rxeof(), use the constant RX_CMD_EMPTY_RXBUF
instead of the magic number 1.
1999-01-16 21:03:57 +00:00
Bill Paul
1b2d762ecc Grrrr... The RealTek 8139 is yet another chip that includes the ethernet
CRC in received frames, which we need to trim manually.
1998-12-24 18:39:48 +00:00
Matthew Dillon
2cbe36f725 probe function changed from returning char * to const char *. 1998-12-14 06:37:37 +00:00
Bill Paul
a43b75fe5e Silence gcc -Wall -ansi -pedantic.
Pointed out by: Eivind
1998-12-10 19:02:07 +00:00
Archie Cobbs
f1d19042b0 The "easy" fixes for compiling the kernel -Wunused: remove unreferenced static
and local variables, goto labels, and functions declared but not defined.
1998-12-07 21:58:50 +00:00
Bill Paul
989c9647f2 if_rl.c: make a small tweak to properly handle the Accton MPX 5030/5038
as a RealTek 8139
if_rlreg.h: use bus_space_read_X() in CSR_READ_X() macros instead of
            directly calling inb()/outb() etc...
rl.4 + RELNOTES.TXT: mention that SMC EtherEZ PCI 1211-TX is supported
                     by the RealTek driver
1998-12-07 00:35:06 +00:00
Bill Paul
36c84dd2b3 Add missing return statement to rl_phy_writereg(). This bug didn't actually
hurt anything, but it's still a bug.

Pointed out by: Jason Wright <jason@thought.net>
1998-11-20 19:26:37 +00:00
Bill Paul
552a0ec7c3 The Accton 1207D adapter uses a chip called the MXP 5030 (or 5038)
which is either a RealTek 8139 in disguise or a RealTek workalike.
This commit fixes the PCI vendor/device ID for this device
and updates the description string to reflect the actual identity
of the device.

I also changed the transmit encapsulation routine to always to
buffer copies on transmit. We end up doing this 99% of the time
anyway. I also tweaked the code that pads packets out to the minimum
length (60) bytes. I was fixing up the m_pkthdr.len value but not
m_len. I don't think this makes that much difference in the grand
scheme of things, but it makes me feel better.
1998-11-18 21:03:58 +00:00
Bill Paul
589e38a609 Add driver support for PCI fast ethernet adapters based on the
RealTek 8129/8139 chipset like I've been threatening. Update kernel
configs, userconfig.c, relnotes and sysinstall. No man page yet;
comming soon.

I consider this driver stable enough that I want to give it some
exposure in -current.
1998-10-18 16:24:34 +00:00