This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
The AHB code:
* hard coded the AR9130 device id;
* assumes a 4k flash calibration space.
This code now extends this:
* hint.ath.X.eepromsize now overrides the eeprom range, instead of 4k
* hint.ath.X.device_id and hint.ath.X.vendor_id can now be overridden.
Tested:
* AR9330 board (Carambola 2)
I've tried serialising TX using queues and such but unfortunately
due to how this interacts with the locking going on elsewhere in the
networking stack, the TX task gets delayed, resulting in quite a
noticable throughput loss:
* baseline TCP for 2x2 11n HT40 is ~ 170mbit/sec;
* TCP for TX task in the ath taskq, with the RX also going on - 80mbit/sec;
* TCP for TX task in a separate, second taskq - 100mbit/sec.
So for now I'm going with the Linux wireless stack approach - lock tx
early. The linux code does in the wireless stack, before the 802.11
state stuff happens and before it's punted to the driver.
But TX locking needs to also occur at the driver layer as the TX
completion code _also_ begins to drain the ifnet TX queue.
Whilst I'm here, add some KTR traces for the TX path.
Note:
* This really should be done at the net80211 layer (as well, at least.)
But that'll have to wait for a little more thought to happen.
the assumption that ath_softc doesn't change size based on build time
configuration.
I picked up on this because suddenly radar stuff didn't work; and
although the ath_dfs code was setting sc_dodfs=1, the main ath driver
saw sc_dodfs=0.
So for now, include opt_ath.h in driver source files. This seems like
the sane thing to do anyway.
I'll have to do a pass over the code at some later stage and turn
the radiotap TX/RX structs into malloc'ed memory, rather than in-line
inside of ath_softc. I'd rather like to keep ath_softc the same
layout regardless of configuration parameters.
Pointy hat to: adrian
* Add a PCU lock, which isn't currently used but will eventually be
used to serialise some of the driver access.
* Add in all the software TX aggregation state, that's kept per-node
and per-TID.
* Add in the software and aggregation state to ath_buf.
* Add in hooks to ath_softc for aggregation state and the (upcoming)
aggregation TX state calls.
* Add / fix the HAL access macros.
Obtained from: Linux, ath9k
Sponsored by: Hobnob, Inc.
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
