The approach taken was the rework zfs_holey() as little as
possible and then just wrap the code as needed to ensure
correct locking and error handling.
Tested with xfstests 285 and 286. All tests pass except for
7-9 of 285 which try to reserve blocks first via fallocate(2)
and fail because fallocate(2) is not yet supported.
Note that the filp->f_lock spinlock did not exist prior to
Linux 2.6.30, but we avoid the need for autotools check by
virtue of the fact that SEEK_DATA/SEEK_HOLE support was not
added until Linux 3.1.
An autoconf check was added for lseek_execute() which is
currently a private function but the expectation is that it
will be exported perhaps as early as Linux 3.11.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1384
Until these hooks are fully implemented return the expected
-EOPNOTSUPP error to indicate they are not functional. This
allows test suites such as xfstests to cleanly skip testing
this functionality until it's implemented.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #229
The definition of zfs_vdev_holder casts VDEV_HOLDER into a function pointer
passing to linux kernel's block layer function blkdev_get_by_path.
However current VDEV_HOLDER is defined to be wider than 32 bits and the compiler
warns about potential overflows. Instead of specifying different values for 32-bit and
64-bit systems using ifdefs, choose the common factor 32-bit addresses.
Redefine VDEV_HOLDER to 0x2401de7("zholder") here.
Signed-off-by: Ying Zhu <casualfisher@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1520
Install the common zfs kernel development headers under
/usr/src/zfs-<version>/ rather than in a kernel specific
directory. The kernel specific build products such as
zfs_config.h and Modules.symvers are left installed under
/usr/src/zfs-<version>/<kernel>.
This was done to be consistent with where dkms expects
kernel module source to be packaged. It also allows for
a common zfs-kmod-devel package which includes the headers,
and per-kernel zfs-kmod-devel-<kernel> packages.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The issue with hot spares in ZoL is because it opens all leaf
vdevs exclusively (O_EXCL). On Linux, exclusive opens cause
subsequent exclusive opens to fail with EBUSY.
This could be resolved by not opening any of the devices
exclusively, which is what Illumos does, but the additional
protection offered by exclusive opens is desirable. It cleanly
prevents you from accidentally adding an in-use non-ZFS device
to your pool.
To fix this we very slightly relaxed the usage of O_EXCL in
the following ways.
1) Functions which open the device but only read had the
O_EXCL flag removed and were updated to use O_RDONLY.
2) A common holder was added to the vdev disk code. This
allow the ZFS code to internally open the device multiple
times but non-ZFS callers may not.
3) An exception was added to make_disks() for hot spare when
creating partition tables. For hot spare devices which
are already opened exclusively we skip creating the partition
table because this must already have been done when the disk
was originally added as a hot spare.
Additional minor changes include fixing check_in_use() to use
a partition instead of a slice suffix. And is_spare() was moved
above make_disks() to avoid adding a forward reference.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#250
It's doubtful many people were impacted by this but commit 6c28567
accidentally broke ZFS builds for 2.6.26 and earlier kernels. This
commit depends on the lookup_bdev() function which exists in 2.6.26
but wasn't exported until 2.6.27.
The availability of the function isn't critical so a wrapper is
introduced which returns ERR_PTR(-ENOTSUP) when the function isn't
defined. This will have the effect of causing zvol_is_zvol() to
always fail for 2.6.26 kernels. This in turn means vdevs will
always get opened concurrently which is good for normal usage.
This will only become an issue if your using a zvol as a vdev in
another pool. In which case you really should be using a newer
kernel anyway.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1205
Added d_clear_d_op() helper function which clears some flags and the
registered dentry->d_op table. This is required because d_set_d_op()
issues a warning when the dentry operations table is already set.
For the .zfs control directory to work properly we must be able to
override the default operations table and register custom .d_automount
and .d_revalidate callbacks.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#1230
Rolling back a mounted filesystem with open file handles and
cached dentries+inodes never worked properly in ZoL. The
major issue was that Linux provides no easy mechanism for
modules to invalidate the inode cache for a file system.
Because of this it was possible that an inode from the previous
filesystem would not get properly dropped from the cache during
rolling back. Then a new inode with the same inode number would
be create and collide with the existing cached inode. Ideally
this would trigger an VERIFY() but in practice the error wasn't
handled and it would just NULL reference.
Luckily, this issue can be resolved by sprucing up the existing
Solaris zfs_rezget() functionality for the Linux VFS.
The way it works now is that when a file system is rolled back
all the cached inodes will be traversed and refetched from disk.
If a version of the cached inode exists on disk the in-core
copy will be updated accordingly. If there is no match for that
object on disk it will be unhashed from the inode cache and
marked as stale.
This will effectively make the inode unfindable for lookups
allowing the inode number to be immediately recycled. The inode
will then only be accessible from the cached dentries. Subsequent
dentry lookups which reference a stale inode will result in the
dentry being invalidated. Once invalidated the dentry will drop
its reference on the inode allowing it to be safely pruned from
the cache.
Special care is taken for negative dentries since they do not
reference any inode. These dentires will be invalidate based
on when they were added to the dentry cache. Entries added
before the last rollback will be invalidate to prevent them
from masking real files in the dataset.
Two nice side effects of this fix are:
* Removes the dependency on spl_invalidate_inodes(), it can now
be safely removed from the SPL when we choose to do so.
* zfs_znode_alloc() no longer requires a dentry to be passed.
This effectively reverts this portition of the code to its
upstream counterpart. The dentry is not instantiated more
correctly in the Linux ZPL layer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#795
Lookups in the snapshot control directory for an existing snapshot
fail with ENOENT if an earlier lookup failed before the snapshot was
created. This is because the earlier lookup causes a negative dentry
to be cached which is never invalidated.
The bug can be reproduced as follows (the second ls should succeed):
$ ls /tank/.zfs/snapshot/s
ls: cannot access /tank/.zfs/snapshot/s: No such file or directory
$ zfs snap tank@s
$ ls /tank/.zfs/snapshot/s
ls: cannot access /tank/.zfs/snapshot/s: No such file or directory
To remedy this, always invalidate cached dentries in the snapshot
control directory. Since these entries never exist on disk there is
no significant performance penalty for the extra lookups.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1192
Use the bdev_physical_block_size() interface to determine the
minimize write size which can be issued without incurring a
read-modify-write operation. This is used to set the ashift
correctly to prevent a performance penalty when using AF hard
disks.
Unfortunately, this interface isn't entirely reliable because
it's not uncommon for disks to misreport this value. For this
reason you may still need to manually set your ashift with:
zpool create -o ashift=12 ...
The solution to this in the upstream Illumos source was to add
a white list of known offending drives. Maintaining such a list
will be a burden, but it still may be worth doing if we can
detect a large number of these drives. This should be considered
as future work.
Reported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#916
Use .mkdir instead of .create in 3.3 compatibility check. Linux 3.6
modifies inode_operations->create's function prototype. This causes
an autotools Linux 3.3. compatibility check for a function prototype
change in create, mkdir and mknode to fail. Since mkdir and mknode
are unchanged, we modify the check to examine it instead.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #873
As of Linux commit 9249e17fe094d853d1ef7475dd559a2cc7e23d42 the
mount flags are now passed to sget() so they can be used when
initializing a new superblock.
ZFS never uses sget() in this fashion so we can simply pass a
zero and add a zpl_sget() compatibility wrapper.
Signed-off-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #873
This reverts commit 395350c85d which
accidentally introduced issue #955.
Pools using AF drives which were originally created with a sector
size of 512 bytes will now be correctly detected to have physical
sector size of 4096. This is desirable for a new pool, however for
an existing pool abruptly changing the sector size causes problems.
For this reason, this change is being reverted until the additional
logic can be added to detect the existing pool case. Existing
pools must use the ashift size stored in the label regardless of
what the disk reports. This is critical for compatibility.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #955
Use the bdev_physical_block_size() interface to determine the
minimize write size which can be issued without incurring a
read-modify-write operation. This is used to set the ashift
correctly to prevent a performance penalty when using AF hard
disks.
Unfortunately, this interface isn't entirely reliable because
it's not uncommon for disks to misreport this value. For this
reason you may still need to manually set your ashift with:
zpool create -o ashift=12 ...
The solution to this in the upstream Illumos source was to add
a while list of known offending drives. Maintaining such a list
will be a burden, but it still may be worth doing if we can
detect a large number of these drives. This should be considered
as future work.
Reported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#916
Remove all of the generated autotools products from the repository
and update the .gitignore files accordingly.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#718
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.
In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).
With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#862
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict(). This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.
However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics. This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#784
The vmtruncate_range() support has been removed from the kernel in
favor of using the fallocate method in the file_operations table.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes. This interface used to
take the child dentry and a bool describing if the parent is needed.
NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.
This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.
Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.
This change also depends on API changes which are available in 2.6.37
and latter kernels. The build system has been updated to detect this,
but there is no compatibility mode for older kernels. This means that
online expansion will NOT be available in older kernels. However, it
will still be possible to expand the vdev offline.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#808
torvalds/linux@adc0e91ab1 introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:
error: implicit declaration of function 'd_alloc_root'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current d_make_root()
interface for readability. Then we introduce an autotools check
to determine if d_make_root() is available. If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#776
The mode argument of iops->create()/mkdir()/mknod() was changed from
an 'int' to a 'umode_t'. To prevent a compiler warning an autoconf
check was added to detect the API change and then correctly set a
zpl_umode_t typedef. There is no functional change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#701
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging. When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.
This checking is particularly helpful when adding new dmu consumers
like Lustre. However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.
--enable-debug-dmu-tx - Enable/disable validation of each tx as
--disable-debug-dmu-tx it is constructed. By default validation
is disabled due to performance concerns.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
Allow a source rpm to be rebuilt with debugging enabled. This
avoids the need to have to manually modify the spec file. By
default debugging is still largely disabled. To enable specific
debugging features use the following options with rpmbuild.
'--with debug' - Enables ASSERTs
# For example:
$ rpmbuild --rebuild --with debug zfs-modules-0.6.0-rc6.src.rpm
Additionally, ZFS_CONFIG has been added to zfs_config.h for
packages which build against these headers. This is critical
to ensure both zfs and the dependant package are using the same
prototype and structure definitions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
DISCARD (REQ_DISCARD, BLKDISCARD) is useful for thin provisioning.
It allows ZVOL clients to discard (unmap, trim) block ranges from
a ZVOL, thus optimizing disk space usage by allowing a ZVOL to
shrink instead of just grow.
We can't use zfs_space() or zfs_freesp() here, since these functions
only work on regular files, not volumes. Fortunately we can use the
low-level function dmu_free_long_range() which does exactly what we
want.
Currently the discard operation is not added to the log. That's not
a big deal since losing discard requests cannot result in data
corruption. It would however result in disk space usage higher than
it should be. Thus adding log support to zvol_discard() is probably
a good idea for a future improvement.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Currently only the (FALLOC_FL_PUNCH_HOLE) flag combination is
supported, since it's the only one that matches the behavior of
zfs_space(). This makes it pretty much useless in its current
form, but it's a start.
To support other flag combinations we would need to modify
zfs_space() to make it more flexible, or emulate the desired
functionality in zpl_fallocate().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #334
The Linux block device queue subsystem exposes a number of configurable
settings described in Linux block/blk-settings.c. The defaults for these
settings are tuned for hard drives, and are not optimized for ZVOLs. Proper
configuration of these options would allow upper layers (I/O scheduler) to
take better decisions about write merging and ordering.
Detailed rationale:
- max_hw_sectors is set to unlimited (UINT_MAX). zvol_write() is able to
handle writes of any size, so there's no reason to impose a limit. Let the
upper layer decide.
- max_segments and max_segment_size are set to unlimited. zvol_write() will
copy the requests' contents into a dbuf anyway, so the number and size of
the segments are irrelevant. Let the upper layer decide.
- physical_block_size and io_opt are set to the ZVOL's block size. This
has the potential to somewhat alleviate issue #361 for ZVOLs, by warning
the upper layers that writes smaller than the volume's block size will be
slow.
- The NONROT flag is set to indicate this isn't a rotational device.
Although the backing zpool might be composed of rotational devices, the
resulting ZVOL often doesn't exhibit the same behavior due to the COW
mechanisms used by ZFS. Setting this flag will prevent upper layers from
making useless decisions (such as reordering writes) based on incorrect
assumptions about the behavior of the ZVOL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
zvol_write() assumes that the write request must be written to stable storage
if rq_is_sync() is true. Unfortunately, this assumption is incorrect. Indeed,
"sync" does *not* mean what we think it means in the context of the Linux
block layer. This is well explained in linux/fs.h:
WRITE: A normal async write. Device will be plugged.
WRITE_SYNC: Synchronous write. Identical to WRITE, but passes down
the hint that someone will be waiting on this IO
shortly.
WRITE_FLUSH: Like WRITE_SYNC but with preceding cache flush.
WRITE_FUA: Like WRITE_SYNC but data is guaranteed to be on
non-volatile media on completion.
In other words, SYNC does not *mean* that the write must be on stable storage
on completion. It just means that someone is waiting on us to complete the
write request. Thus triggering a ZIL commit for each SYNC write request on a
ZVOL is unnecessary and harmful for performance. To make matters worse, ZVOL
users have no way to express that they actually want data to be written to
stable storage, which means the ZIL is broken for ZVOLs.
The request for stable storage is expressed by the FUA flag, so we must
commit the ZIL after the write if the FUA flag is set. In addition, we must
commit the ZIL before the write if the FLUSH flag is set.
Also, we must inform the block layer that we actually support FLUSH and FUA.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The second argument of sops->show_options() was changed from a
'struct vfsmount *' to a 'struct dentry *'. Add an autoconf check
to detect the API change and then conditionally define the expected
interface. In either case we are only interested in the zfs_sb_t.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#549
When the original build system code was added the release
component was accidentally omited from the development header
install path. This patch adds the missing path component so
it's always clear exactly what release your compiling against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The Linux 3.1 kernel has introduced the concept of per-filesystem
shrinkers which are directly assoicated with a super block. Prior
to this change there was one shared global shrinker.
The zfs code relied on being able to call the global shrinker when
the arc_meta_limit was exceeded. This would cause the VFS to drop
references on a fraction of the dentries in the dcache. The ARC
could then safely reclaim the memory used by these entries and
honor the arc_meta_limit. Unfortunately, when per-filesystem
shrinkers were added the old interfaces were made unavailable.
This change adds support to use the new per-filesystem shrinker
interface so we can continue to honor the arc_meta_limit. The
major benefit of the new interface is that we can now target
only the zfs filesystem for dentry and inode pruning. Thus we
can minimize any impact on the caching of other filesystems.
In the context of making this change several other important
issues related to managing the ARC were addressed, they include:
* The dnlc_reduce_cache() function which was called by the ARC
to drop dentries for the Posix layer was replaced with a generic
zfs_prune_t callback. The ZPL layer now registers a callback to
drop these dentries removing a layering violation which dates
back to the Solaris code. This callback can also be used by
other ARC consumers such as Lustre.
arc_add_prune_callback()
arc_remove_prune_callback()
* The arc_reduce_dnlc_percent module option has been changed to
arc_meta_prune for clarity. The dnlc functions are specific to
Solaris's VFS and have already been largely eliminated already.
The replacement tunable now represents the number of bytes the
prune callback will request when invoked.
* Less aggressively invoke the prune callback. We used to call
this whenever we exceeded the arc_meta_limit however that's not
strictly correct since it results in over zeleous reclaim of
dentries and inodes. It is now only called once the arc_meta_limit
is exceeded and every effort has been made to evict other data from
the ARC cache.
* More promptly manage exceeding the arc_meta_limit. When reading
meta data in to the cache if a buffer was unable to be recycled
notify the arc_reclaim thread to invoke the required prune.
* Added arcstat_prune kstat which is incremented when the ARC
is forced to request that a consumer prune its cache. Remember
this will only occur when the ARC has no other choice. If it
can evict buffers safely without invoking the prune callback
it will.
* This change is also expected to resolve the unexpect collapses
of the ARC cache. This would occur because when exceeded just the
arc_meta_limit reclaim presure would be excerted on the arc_c
value via arc_shrink(). This effectively shrunk the entire cache
when really we just needed to reclaim meta data.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#466Closes#292
Directly changing inode->i_nlink is deprecated in Linux 3.2 by commit
SHA: bfe8684869601dacfcb2cd69ef8cfd9045f62170
Use the new set_nlink() kernel function instead.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #462
Added the necessary build infrastructure for building packages
compatible with the Arch Linux distribution. As such, one can now run:
$ ./configure
$ make pkg # Alternatively, one can run 'make arch' as well
on the Arch Linux machine to create two binary packages compatible with
the pacman package manager, one for the zfs userland utilities and
another for the zfs kernel modules. The new packages can then be
installed by running:
# pacman -U $package.pkg.tar.xz
In addition, source-only packages suitable for an Arch Linux chroot
environment or remote builder can also be build using the 'sarch' make
rule.
NOTE: Since the source dist tarball is created on the fly from the head
of the build tree, it's MD5 hash signature will be continually influx.
As a result, the md5sum variable was intentionally omitted from the
PKGBUILD files, and the '--skipinteg' makepkg option is used. This may
or may not have any serious security implications, as the source tarball
is not being downloaded from an outside source.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#491
Update the code to use the bdi_setup_and_register() helper to
simplify the bdi integration code. The updated code now just
registers the bdi during mount and destroys it during unmount.
The only complication is that for 2.6.32 - 2.6.33 kernels the
helper wasn't available so in these cases the zfs code must
provide it. Luckily the bdi_setup_and_register() function
is trivial.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#367
For a long time now the kernel has been moving away from using the
pdflush daemon to write 'old' dirty pages to disk. The primary reason
for this is because the pdflush daemon is single threaded and can be
a limiting factor for performance. Since pdflush sequentially walks
the dirty inode list for each super block any delay in processing can
slow down dirty page writeback for all filesystems.
The replacement for pdflush is called bdi (backing device info). The
bdi system involves creating a per-filesystem control structure each
with its own private sets of queues to manage writeback. The advantage
is greater parallelism which improves performance and prevents a single
filesystem from slowing writeback to the others.
For a long time both systems co-existed in the kernel so it wasn't
strictly required to implement the bdi scheme. However, as of
Linux 2.6.36 kernels the pdflush functionality has been retired.
Since ZFS already bypasses the page cache for most I/O this is only
an issue for mmap(2) writes which must go through the page cache.
Even then adding this missing support for newer kernels was overlooked
because there are other mechanisms which can trigger writeback.
However, there is one critical case where not implementing the bdi
functionality can cause problems. If an application handles a page
fault it can enter the balance_dirty_pages() callpath. This will
result in the application hanging until the number of dirty pages in
the system drops below the dirty ratio.
Without a registered backing_device_info for the filesystem the
dirty pages will not get written out. Thus the application will hang.
As mentioned above this was less of an issue with older kernels because
pdflush would eventually write out the dirty pages.
This change adds a backing_device_info structure to the zfs_sb_t
which is already allocated per-super block. It is then registered
when the filesystem mounted and unregistered on unmount. It will
not be registered for mounted snapshots which are read-only. This
change will result in flush-<pool> thread being dynamically created
and destroyed per-mounted filesystem for writeback.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#174
Unlike most other Linux distributions archlinux installs its
init scripts in /etc/rc.d insead of /etc/init.d. This commit
provides an archlinux rc.d script for zfs and extends the
build infrastructure to ensure it get's installed in the
correct place.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#322
The .get_sb callback has been replaced by a .mount callback
in the file_system_type structure. When using the new
interface the caller must now use the mount_nodev() helper.
Unfortunately, the new interface no longer passes the vfsmount
down to the zfs layers. This poses a problem for the existing
implementation because we currently save this pointer in the
super block for latter use. It provides our only entry point
in to the namespace layer for manipulating certain mount options.
This needed to be done originally to allow commands like
'zfs set atime=off tank' to work properly. It also allowed me
to keep more of the original Solaris code unmodified. Under
Solaris there is a 1-to-1 mapping between a mount point and a
file system so this is a fairly natural thing to do. However,
under Linux they many be multiple entries in the namespace
which reference the same filesystem. Thus keeping a back
reference from the filesystem to the namespace is complicated.
Rather than introduce some ugly hack to get the vfsmount and
continue as before. I'm leveraging this API change to update
the ZFS code to do things in a more natural way for Linux.
This has the upside that is resolves the compatibility issue
for the long term and fixes several other minor bugs which
have been reported.
This commit updates the code to remove this vfsmount back
reference entirely. All modifications to filesystem mount
options are now passed in to the kernel via a '-o remount'.
This is the expected Linux mechanism and allows the namespace
to properly handle any options which apply to it before passing
them on to the file system itself.
Aside from fixing the compatibility issue, removing the
vfsmount has had the benefit of simplifying the code. This
change which fairly involved has turned out nicely.
Closes#246Closes#217Closes#187Closes#248Closes#231
The security_inode_init_security() function now takes an additional
qstr argument which must be passed in from the dentry if available.
Passing a NULL is safe when no qstr is available the relevant
security checks will just be skipped.
Closes#246Closes#217Closes#187
The inode eviction should unmap the pages associated with the inode.
These pages should also be flushed to disk to avoid the data loss.
Therefore, use truncate_setsize() in evict_inode() to release the
pagecache.
The API truncate_setsize() was added in 2.6.35 kernel. To ensure
compatibility with the old kernel, the patch defines its own
truncate_setsize function.
Signed-off-by: Prasad Joshi <pjoshi@stec-inc.com>
Closes#255
The WRITE_FLUSH, WRITE_FUA, and WRITE_FLUSH_FUA flags have been
introduced as a replacement for WRITE_BARRIER. This was done
to allow richer semantics to be expressed to the block layer.
It is the block layers responsibility to choose the correct way
to implement these semantics.
This change simply updates the bio's to use the new kernel API
which should be absolutely safe. However, since ZFS depends
entirely on this working as designed for correctness we do
want to be careful.
Closes#281
The previous commit 8a7e1ceefa wasn't
quite right. This check applies to both the user and kernel space
build and as such we must make sure it runs regardless of what
the --with-config option is set too.
For example, if --with-config=kernel then the autoconf test does
not run and we generate build warnings when compiling the kernel
packages.
Gcc versions 4.3.2 and earlier do not support the compiler flag
-Wno-unused-but-set-variable. This can lead to build failures
on older Linux platforms such as Debian Lenny. Since this is
an optional build argument this changes add a new autoconf check
for the option. If it is supported by the installed version of
gcc then it is used otherwise it is omited.
See commit's 12c1acde76 and
79713039a2 for the reason the
-Wno-unused-but-set-variable options was originally added.
How nfsd handles .fsync() has been changed a couple of times in the
recent kernels. But basically there are three cases we need to
consider.
Linux 2.6.12 - 2.6.33
* The .fsync() hook takes 3 arguments
* The nfsd will call .fsync() with a NULL file struct pointer.
Linux 2.6.34
* The .fsync() hook takes 3 arguments
* The nfsd no longer calls .fsync() but instead used sync_inode()
Linux 2.6.35 - 2.6.x
* The .fsync() hook takes 2 arguments
* The nfsd no longer calls .fsync() but instead used sync_inode()
For once it looks like we've gotten lucky. The first two cases can
actually be collased in to one if we stop using the file struct
pointer entirely. Since the dentry is still passed in both cases
this is possible. The last case can then be safely handled by
unconditionally using the dentry in the file struct pointer now
that we know the nfsd caller has been removed.
Closes#230
This change fixes a kernel panic which would occur when resizing
a dataset which was not open. The objset_t stored in the
zvol_state_t will be set to NULL when the block device is closed.
To avoid this issue we pass the correct objset_t as the third arg.
The code has also been updated to correctly notify the kernel
when the block device capacity changes. For 2.6.28 and newer
kernels the capacity change will be immediately detected. For
earlier kernels the capacity change will be detected when the
device is next opened. This is a known limitation of older
kernels.
Online ext3 resize test case passes on 2.6.28+ kernels:
$ dd if=/dev/zero of=/tmp/zvol bs=1M count=1 seek=1023
$ zpool create tank /tmp/zvol
$ zfs create -V 500M tank/zd0
$ mkfs.ext3 /dev/zd0
$ mkdir /mnt/zd0
$ mount /dev/zd0 /mnt/zd0
$ df -h /mnt/zd0
$ zfs set volsize=800M tank/zd0
$ resize2fs /dev/zd0
$ df -h /mnt/zd0
Original-patch-by: Fajar A. Nugraha <github@fajar.net>
Closes#68Closes#84
Added insert_inode_locked() helper function, prior to this most callers
used insert_inode_hash(). The older method doesn't check for collisions
in the inode_hashtable but it still acceptible for use. Fallback to
using insert_inode_hash() when insert_inode_locked() is unavailable.
The blk_queue_stackable() queue flag was added in 2.6.27 to handle dm
stacking drivers. Prior to this request stacking drivers were detected
by checking (q->request_fn == NULL), for earlier kernels we revert to
this legacy behavior.
To support automatically mounting your zfs on filesystem on boot
a basic init script is needed. Unfortunately, every distribution
has their own idea of the _right_ way to do things. Rather than
write one very complicated portable init script, which would be
invariably replaced by the distributions own anyway. I have
instead added support to provide multiple distribution specific
init scripts.
The correct init script for your distribution will be selected
by ZFS_AC_DEFAULT_PACKAGE which will set DEFAULT_INIT_SCRIPT.
During 'make install' the correct script for your system will
be installed from zfs/etc/init.d/zfs.DEFAULT_INIT_SCRIPT to the
usual /etc/init.d/zfs location.
Currently, there is zfs.fedora and a more generic zfs.lsb init
script. Hopefully, the distribution maintainers who know best
how they want their init scripts to function will feedback their
approved versions to be included in the project.
This change does not consider upstart jobs but I'm not at all
opposed to add that sort of thing.
