discarded RX packets to input error for BCM5705 or newer chipset as the others.
Unfortunately we cannot do the same for output errors because ifOutDiscards
equivalent register does not exist. While I am here, replace misleading and
wrong BGE_RX_STATS/BGE_TX_STATS with BGE_MAC_STATS. They were reversed but
worked accidently.
machines and both TX and RX were broken on big-endian machines.
The chip design is crazy -- on RX, it puts the 16-bit VLAN tag
in network byte order (big-endian) in the 32-bit little-endian
register!
Thanks to John Baldwin for helping me document this change! ;-)
Tested by: sat (amd64), test program (sparc64)
PR: kern/105054
MFC after: 3 days
aue_tick calls several synchronous usb functions from a timeout(9),
this is very broken since a timeout(9) is run as an interrupt
and the usb functions tsleep.
A stopgap fix is to schedule a taskqueue task from the timeout
and defer work to that taskqueue task.
Preliminary support for Atmel AT45D series of DataFlash on the
SPI bus (ok, not really a hardware bus, but a logical
connection). This works only for the 8MB version of the part
due to hard coding. Both read and write are supported.
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- In rlphy_status() just use if_dname instead of determining the name
of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)).
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
- Fix some whitespace nits and remove commented out code that just can't
be used with RealTek PHYs.
MFC after: 2 weeks
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- Don't set MIIF_NOISOLATE so qsphy(4) can be used in configurations
with multiple PHYs. There doesn't seem to be a problem with isolating
QS6612 per se nor in combination with the NICs they're used with.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
Obtained from: NetBSD (except for the first item)
MFC after: 2 weeks
loopback to work PCnet chips additionally need to be placed into
external loopback mode which pcn(4) doesn't do so far.
- In nsphy_service() just use if_dname instead of determining the name
of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)).
- Don't set MIIF_NOISOLATE, except for when used in combination with a
NIC that wedges when isolating the PHYs, so nsphy(4) can be used in
configurations with multiple PHYs.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG
added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19).
- Implement a separate nsphy_reset(). There are two reasons for this:
1) This PHY can take an inordinate amount of time to reset if media
is attached; under fairly normal circumstances up to nearly one
second. This is because it appears to go through an implicit auto-
negotiation cycle as part of the reset.
2) During reset and auto-negotiation, the BMCR will clear the reset
bit before the process is complete. It will return 0 until the
process is complete and it's safe to access the PHY again.
This is the first of two changes required to make the combination of
Am79c971 and DP83840A found on certain HP cards and on-board in IBM
machines work.
- Fix some whitespace nits.
Based on: NetBSD (except for the first and second item)
MFC after: 2 weeks
with multiple PHYs. There doesn't seem to be a problem with isolating
LXT970 per se nor in combination with the NICs they're used with and
lxtphy(4) was already adding IFM_NONE anyway.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
- Fix some whitespace nits.
Obtained from: NetBSD
MFC after: 2 weeks
the BMSR contains any media at all to mii_phy_add_media(). The majority
of the drivers currently using mii_phy_add_media() were missing such a
check anyway though.
MFC after: 2 weeks
take place if IFM_AUTO is selected. This allows drivers like nsphy(4),
which need to force writing the ANAR according to the BMSR, to take
advantage of mii_phy_setmedia(). [1]
- In mii_phy_reset() once the current media is set don't isolate the PHY
corresponding to the instance of the currently selected media rather
than unconditionally not isolating the PHY corresponding to instance 0.
This saves a isolation-unisolation-cycle of the PHY corresponding to
the currently selected media for the case were it isn't instance 0.
- Fix some whitespace nits. [1]
Obtained from: NetBSD [1]
MFC after: 2 weeks
an URQ_REQUEST when DMA segments are passed to usbd_start_transfer();
when the request doesn't include the optional data buffer the size of
the transfer (xfer->length) is 0, in which case usbd_transfer() won't
create a DMA map but call usbd_start_transfer() with no DMA segments.
With the previous change this could result in the bus_dmamap_sync()
implementation dereferencing the NULL-pointer passed as the DMA map
argument.
While at it fix what appears to be a typo in usbd_start_transfer();
in order to determine wheter usbd_start_transfer() was called with
DMA segments check whether the number of segments is > 0 rather than
the pointer to them being > 0.
OK'ed by: imp
in every sense.
General
-------
- Multichannel safe, endian safe, format safe
* Large part of critical pcm filters such as vchan.c, feeder_rate.c,
feeder_volume.c, feeder_fmt.c and feeder.c has been rewritten so that
using them does not cause the pcm data to be converted to 16bit little
endian.
* Macrosses for accessing pcm data safely are defined within sound.h in
the form of PCM_READ_* / PCM_WRITE_*
* Currently, most of them are probably limited for mono/stereo handling,
but the future addition of true multichannel will be much easier.
- Low latency operation
* Well, this require lot more works to do not just within sound driver,
but we're heading towards right direction. Buffer/block sizing within
channel.c is rewritten to calculate precise allocation for various
combination of sample/data/rate size. As a result, applying correct
SNDCTL_DSP_POLICY value will achive expected latency behaviour simmilar
to what commercial 4front driver do.
* Signal handling fix. ctrl+c of "cat /dev/zero > /dev/dsp" does not
result long delay.
* Eliminate sound truncation if the sound data is too small.
DIY:
1) Download / extract
http://people.freebsd.org/~ariff/lowlatency/shortfiles.tar.gz
2) Do a comparison between "cat state*.au > /dev/dsp" and
"for x in state*.au ; do cat $x > /dev/dsp ; done"
- there should be no "perceivable" differences.
Double close for PR kern/31445.
CAVEAT: Low latency come with (unbearable) price especially for poorly
written applications. Applications that trying to act smarter
by requesting (wrong) blocksize/blockcount will suffer the most.
Fixup samples/patches can be found at:
http://people.freebsd.org/~ariff/ports/
- Switch minimum/maximum sampling rate limit to "1" and "2016000" (48k * 42)
due to closer compatibility with 4front driver.
Discussed with: marcus@ (long time ago?)
- All driver specific sysctls in the form of "hw.snd.pcm%d.*" have been
moved to their own dev sysctl nodes, notably:
hw.snd.pcm%d.vchans -> dev.pcm.%d.vchans
Bump __FreeBSD_version.
Driver specific
---------------
- Ditto for sysctls.
- snd_atiixp, snd_es137x, snd_via8233, snd_hda
* Numerous cleanups and fixes.
* _EXPERIMENTAL_ polling mode support using simple callout_* mechanisme.
This was intended for pure debugging and latency measurement, but proven
good enough in few unexpected and rare cases (such as problematic shared
IRQ with GIANT devices - USB). Polling can be enabled/disabled through
dev.pcm.0.polling. Disabled by default.
- snd_ich
* Fix possible overflow during speed calibration. Delay final
initialization (pcm_setstatus) after calibration finished.
PR: kern/100169
Tested by: Kevin Overman <oberman@es.net>
* Inverted EAPD for few Nec VersaPro.
PR: kern/104715
Submitted by: KAWATA Masahiko <kawata@mta.biglobe.ne.jp>
Thanks to various people, notably Joel Dahl, Yuriy Tsibizov, Kevin Oberman,
those at #freebsd-azalia @ freenode and others for testing.
Joel Dahl will do the manpage update.
- incorporate csjp's fix for a mishandled endian conversion
- convert PAGE_SIZE to 4096 for PCIe adapter workaround (my page size is not 4k)
- implement em_read_pcie_cap_reg where we set the max read size on pcie to 4k (taken from mxge)
Reviewed by: scottl and jfvogel
I have been debugging the usb problems some more. Your were
right in your assumption (thanks for the pointer) about lack
of calls to bus_dmamap_sync(). In usbdi.c bus_dmamap_sync()
does get used for transfers that move data from PC to USB and
it is used for transfers that move data from USB to PC. But
someone forgot that control transfers consist of possibly two
data chunks : the request itself and optionally a buffer of
data that should be transfered to or from the USB device. On
requests to the control endpoint without additional data
bus_dmamap_sync() didn't get called. For some reason my first
tests with umass worked (due to enough cache poisening I
guess). The attached patch adds a call to bus_dmamap_sync()
to usbdi.c and now all devices I have tried work out of the
box. I have successfully transfered large files using the
if_axe driver and I have mounted several different umass
devices.
submitted by: Daan Vreeken
sponsored by: Vitsch Electronics
reviewed by: cognet@
- Fix bug preventing adoption of running firmware
- Set PCIe max read request size to 4KB
- Read PCIe link width from config space
- Assume aligned completions from the southbridge ports
of intel E5000 chips
- Use aligned firmware when link width is x4 or less
- Add hw.mxge.force_firmware tunable to allow user to force
selection of aligned (or unaligned) firmware
