* Support for sam9 "EMAC" controller.
* Support for rmii interface to phy.
at91.c & at91sam9.c:
* Eliminate separate at91sam9.c file.
* Add new devices to at91sam9_devs table.
at91_machdep.c & at at91sam9_machdep.c:
* Automatic chip type determination.
* Remove compile time chip dependencies.
* Eliminate separate at91sam9_machdep.c file.
at91_pmc.c:
* Corrected support for all of the sam926? and sam9g20 chips.
* Remove compile time chip dependencies.
My apologies to Greg for taking so long to take care of it.
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
- Reorder detach so that ether_ifdetach() is called first. This removes
the race that ATE_FLAG_DETACHING closed, so that flag can be removed.
- Trim a duplicate clearing of IFF_DRV_RUNNING.
Reviewed by: imp
will initialize the FIFO memory correctly on attach. Before
that this values was intialized in only in at91_usart_bus_attach
which is called after the uart(4) memory allocation happens.
Approved by: re (kib)
MFC after: 1 week
DPCPU area was not properly mapped into kernel VA space, which caused page
fault on the first DPCPU access. This patch fixes the problem by mapping DPCPU
area into kernel VA space.
Submitted by: Michal Hajduk, Piotr Ziecik
Reviewed by: cognet, stas
Approved by: re (kib)
Obtained from: Semihalf
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
- Modules and kernel code alike may use DPCPU_DEFINE(),
DPCPU_GET(), DPCPU_SET(), etc. akin to the statically defined
PCPU_*. Requires only one extra instruction more than PCPU_* and is
virtually the same as __thread for builtin and much faster for shared
objects. DPCPU variables can be initialized when defined.
- Modules are supported by relocating the module's per-cpu linker set
over space reserved in the kernel. Modules may fail to load if there
is insufficient space available.
- Track space available for modules with a one-off extent allocator.
Free may block for memory to allocate space for an extent.
Reviewed by: jhb, rwatson, kan, sam, grehan, marius, marcel, stas
the implementation can guarantee forward progress in the event of
a stuck interrupt or interrupt storm. This is especially critical
for fast interrupt handlers, as they can cause a hard hang in that
case. When first called, arm_get_next_irq() is passed -1.
Obtained from: Juniper Networks, Inc.
registers contents.
- Use memory barriers to preserve the order of buffer space operations.
This might be needed if we'll ever use this driver on architectures
where ordering is not guaranteed.
operates in the common memory mode and use polling mode to control
the status of operations as I don't have any board with interrupt
line routed yet. I'll add the GPIO interrupt driven mode as soon
as I get one.
at91_udp.c does not exist anymore, it is now replaced by at91dci in
src/sys/dev/usb/controller. Also remove the ohci_atmelarm.c because it is also
included in src/sys/conf/files
Submitted by: Sylvestre Gallon
usb stack rather than with the rest of the processor support code.
Not sure that's a good idea, as we were moving away from it, but this
fixes the build in the mean time so we can have that discussion.
rather than a fixed 512... This fixes the mount root problem on at91.
Prior to the SD card reorg, all data transfers were 512 bytes, so we
didn't notice.
the serial port class when we set the devclass since it is now
no-longer a compile time constant. Eliminate the pci include, as it
isn't relevant or necessary.
