The device mapping table contains sc->max_devices entries, so only
indices in [0, sc->max_devices) are valid.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27964
Previously we copied in the request into a stack-allocated structure
that could be smaller than the request size. Furthermore, we checked
the request size only after doing the copyin.
Fix this by allocating a buffer to hold the request, then copying the
buffer's contents into a command descriptor. This is a bit heavy-handed
but I expect the overhead will not be noticeable. The approach of
coping the header in first is susceptible to TOCTOU problems.
Reviewed by: imp
Reported by: maxpl0it@protonmail.com
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27963
Replace MAXPHYS by runtime variable maxphys. It is initialized from
MAXPHYS by default, but can be also adjusted with the tunable kern.maxphys.
Make b_pages[] array in struct buf flexible. Size b_pages[] for buffer
cache buffers exactly to atop(maxbcachebuf) (currently it is sized to
atop(MAXPHYS)), and b_pages[] for pbufs is sized to atop(maxphys) + 1.
The +1 for pbufs allow several pbuf consumers, among them vmapbuf(),
to use unaligned buffers still sized to maxphys, esp. when such
buffers come from userspace (*). Overall, we save significant amount
of otherwise wasted memory in b_pages[] for buffer cache buffers,
while bumping MAXPHYS to desired high value.
Eliminate all direct uses of the MAXPHYS constant in kernel and driver
sources, except a place which initialize maxphys. Some random (and
arguably weird) uses of MAXPHYS, e.g. in linuxolator, are converted
straight. Some drivers, which use MAXPHYS to size embeded structures,
get private MAXPHYS-like constant; their convertion is out of scope
for this work.
Changes to cam/, dev/ahci, dev/ata, dev/mpr, dev/mpt, dev/mvs,
dev/siis, where either submitted by, or based on changes by mav.
Suggested by: mav (*)
Reviewed by: imp, mav, imp, mckusick, scottl (intermediate versions)
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D27225
SAM-3 specification introduced concept of Task Priority, that was renamed
to Command Priority in SAM-4, and supported by all modern SCSI transports.
It provides 15 levels of relative priorities: 1 - highest, 15 - lowest and
0 - default. SAT specification for SATA devices translates priorities 1-3
into NCQ high priority.
This change adds new "priority" field into empty spots of struct ccb_scsiio
and struct ccb_accept_tio of CAM and struct ctl_scsiio of CTL. Respective
support is added into iscsi(4), isp(4), mpr(4), mps(4) and ocs_fc(4) drivers
for both initiator and where applicable target roles. Minimal support was
added to CTL to receive the priority value from different frontends, pass it
between HA controllers and report in few places.
This patch does not add consumers of this functionality, so nothing should
really change yet, since the field is still set to 0 (default) on initiator
and not actively used on target. Those are to be implemented separately.
I've confirmed priority working on WD Red SATA disks connected via mpr(4)
and properly transferred to CTL target via iscsi(4), isp(4) and ocs_fc(4).
While there, added missing tag_action support to ocs_fc(4) initiator role.
MFC after: 1 month
Relnotes: yes
Sponsored by: iXsystems, Inc.
that can be extended, but also ensure compile-time type checking. Refactor
common code out of arch-specific implementations. Move the mpr and mps
drivers to this new API. The template type remains visible to the consumer
so that it can be allocated on the stack, but should be considered opaque.
This memset() wiped MPI2_FUNCTION_SCSI_TASK_MGMT set by mprsas_alloc_tm(),
that broke target reset on device removal, making later re-insertion into
the same slot impossible, since firmware was still waiting for the driver
to finish with the removed device.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
Copy the CP, PTRIN, etc macros from freebsd32.h into a sys/abi_compat.h
and replace existing definitation with includes where required. This
eliminates duplicate code and allows Linux and FreeBSD compatability
headers to be included in the same files.
Input from: cem, jhb
Obtained from: CheriBSD
MFC after: 2 weeks
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24275
192 bytes are not enough to print long commands, such as ATA COMMAND PASS
THROUGH(16), that makes debug output difficult to read.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Remove a number of workarounds for older versions of FreeBSD. FreeBSD stable/10
was branched over 6 years ago. All of these changes date from about that time or
earlier. These workarounds are extensive and get in the way of understanding
the current flow in the driver.
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
commands have completed.
It's not OK to force complete any pending commands before we send the
REMOVE_DEVICE. Instead, make sure that all pending commands are complete before
sending that. By trying to second guess the firmware here, we run the risk of
completing commands twice, which leads to corruption.
This removes the forced completion of commands introduced in r218811. So it's a
partial backout of that commit, but replaces it with a more rebust
mechanism. Either these commands will complete due to the TARGET RESET, or they
will timeout and be aborted, but they will all complete.
Add assert that all commands are complete to REMOVE_DEVICE completion
routine. We attempt to assure this programatically, so we shouldn't have any
commands in the queue because we've waited for them all. Any commands that make
it into our action routine after we mark the target in removal will complete
immediately with an error.
When we're removing a target that's not a volume, advertise up the stack that
it's actually gone, as opposed to having a transient selection error we should
retry. Do this both in the action routine, and when we get a notification of an
aborted command. We don't do this for volumes because the driver tries hard not
to advertise to the OS a volume has disappeared.
Apply these changes to both mpr and mps since they are based on quite similar
designs.
Discussed with: scottl@
Differential Revision: https://reviews.freebsd.org/D23768
in the sysctl block for the driver. mpsutil/mprutil needs this so it can
know how big of a buffer to allocate when requesting the IOCFacts from the
controller. This eliminates the kernel console messages about wrong
allocation sizes.
Reported by: imp
When we get a device departed message from the firmware, we send a TARGET_REST
to the device to let the firmware know we're done and as part of the recovery
process. This will abort all the commands. While the documentation says the IOC
is responsible for writing the completion message for all the commands pending
with an aborted status, we sometimes have queued commands for the target that
haven't been completed so are in the INQUEUE state. So, when we later complete
the pending CCB as aborted, these commands are freed and we hit the "state not
busy" panic.
Elsewhere where we dequeue commands, we move the state to BUSY from INQUEUE. Do
that here as well. In talking to Ken, Scott and Justin, they recommended a
series of tests to see if this is 100% safe. Those tests are ongoing, but
preliminary tests suggest this is safe as we see no duplicate completions when
we hit this case at work. We have a machine that has a dodgy powersupply which
usually doesn't apply power to a few drives, but sometimes does when the machine
is under heavy load so we get a rash of the connect / disconnect messages over
half an hour. Without this change, we'd see state not busy panic. With this
change, the drives just annoyingly come and go without affecting the rest of the
machine, but without a complete error injection test suite, it's hard to know if
all edge cases are now covered or not.
Discussed with: scottl, ken, gibbs
When a command is finished running, we must transition it from INQUEUE
to busy state. We were failing to do that, so we hit a panic when the
commands were freed. This only affects mpr, mps already did simmilar
things. Now both the polling and interrupt paths properly set BUSY as
appropriate.
Eliminate the TIMEDOUT state. This state really conveyed two different
concepts: I timed out during recovery (and my command got put on the
recovery queue), and I timed out diring discovery (which doesn't).
Separate those two concepts into two flags. Use the TIMEDOUT flag to
fail requests as timed out. Use the on queue flag to remove them from
the queue.
In mps_intr_locked for MPI2_RPY_DESCRIPT_FLAGS_ADDRESS_REPLY message
type, when completing commands, ignore the ones that are not in state
INQUEUE. They were already completed as part of the recovery
process. When we complete them twice, we wind up with entries on the
free queue that are marked as busy, trigging asserts.
Reviewed by: scottl (earlier version, just for mpr)
Differential Revision: https://reviews.freebsd.org/D20785
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
are successfully returned by the card (usually due to an abort being issued
as part of timeout recovery). Remove what amounts to an insufficient
KASSERT, and don't overwrite the state value. State should probably be
re-designed, and that will be done with a future commit.
Reported by: phk, bei.io
Reviewed by: imp, mav
Differential Revision: D19677
Due to HW Errta on Aero/Sea A0 chipset on secure boot mode & on heavy IO load,
sometimes read operation on MPT Fusion registers will give zero value,
So, as a workaround driver will retry the MPT Fusion register
read operation for max three times upon reading zero value form these
registers.
Submitted by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
Enable atomic type descriptor support only for Sea & Aero cards,
due to HW errata this atomic descriptor support has to be disabled
on Ventura cards.
Submitted by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
Added deviceID's for Sea,Aero to mpr Driver
Aero:
0x00E0 Invalid
0x00E1 Configurable Secure
0x00E2 Hard Secure
0x00E3 Tampered
Sea:
0x00E4 Invalid
0x00E5 Configurable Secure
0x00E6 Hard Secure
0x00E7 Tampered
For Tampered & Invalid type cards, driver will claim the device & quit the probe function with below error message,
"HBA is in Non Secure mode"
for Configurable Secure type cards, driver will display below message in .probe() callback function,
"HBA is in Configurable Secure mode"
Submitted by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
Following list of changes done in the driver as a part of TM handling on the NVMe drives.
Below changes are only applicable on NVMe drives and only when custom NVMe TM handling bit is set to zero by IOC.
1. Issue LUN reset & Target reset TMs with Target reset method field set to Protocol Level reset (0x3),
2. For LUN & target reset TMs use the timeout value as ControllerResetTO value provided by firmware using PCie Device Page 0,
3. If LUN reset fails to terminates the IO then directly escalate to host reset instead of going for target reset TM,
4. For Abort TM use the timeout value as NVMeAbortTO value given by the IOC using Manufacturing Page 11,
5. Log message "PCie Host Reset failed" message up on receiving P
Submitted by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
typedef struct mps_pass_thru
{
uint64_t PtrRequest;
uint64_t PtrReply;
uint64_t PtrData;
uint32_t RequestSize;
uint32_t ReplySize;
uint32_t DataSize;
uint32_t DataDirection;
uint64_t PtrDataOut;
uint32_t DataOutSize;
uint32_t Timeout;
} mps_pass_thru_t, * ptrmpssas_pass_thru_t;
In the above mps_pass_thru structure; Application expects PrtReply buffer
should contain both MPI reply followed by sense data. So, updated driver
to copy sense data at PtrReply + sizeof(MPI2 reply) location where
application wants the driver to copy back the sense data info.
Submitted by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
Add a generic mechanism to override mp?_wait_command's timeout behavior,
which continues to invoke reinit by default. Invokers who set
cm_timeout_handler may avoid automatic reinit and do their own handling.
Adapt mp?sas_get_sata_identify to this mechanism and remove its callout
hack.
Reviewed by: scottl
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D18614
In the event that the ID command timed out, mps(4)/mpr(4) did not free the
command until it could be cancelled. However, it freed the associated
buffer (cm_data). Fix the lifetime issue by freeing the associated buffer
only after Abort Task or controller reset.
Reviewed by: scottl
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D18612
The original NVMe API used bit-fields to represent fields in data
structures defined by the specification (e.g. the op-code in the command
data structure). The implementation targeted x86_64 processors and
defined the bit fields for little endian dwords (i.e. 32 bits).
This approach does not work as-is for big endian architectures and was
changed to use a combination of bit shifts and masks to support PowerPC.
Unfortunately, this changed the NVMe API and forces #ifdef's based on
the OS revision level in user space code.
This change reverts to something that looks like the original API, but
it uses bytes instead of bit-fields inside the packed command structure.
As a bonus, this works as-is for both big and little endian CPU
architectures.
Bump __FreeBSD_version to 1200081 due to API change
Reviewed by: imp, kbowling, smh, mav
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D16404
r330951 by smh fixed the mps driver to avoid deadlocks when panicing.
The same code is needed for mpr, so port it here, along with the fix
which allows the CCBs scheduled to complete avoiding at least a scary
message and likely other unintended consequences.
Sponsored by: Netflix
Differential Review: https://reviews.freebsd.org/D16663
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
The mps(4) and mpr(4) drivers and hardware handle T10 Protection
Information, which is a system of checksums and guard blocks to protect
data while it is being transferred and while it is on disk. It is also
known as T10 DIF. For more details, see section 4.22 of the SBC-4 spec.
Supporting Type 2 protection requires using 32 byte CDBs, and filling in
the fields in those CDBs. We don't yet support that in the da(4) driver.
Type 1 and Type 3 protection don't require that, and can be handled by
the mps(4)/mpr(4) driver's code and firmware without any additional
input from the da(4) driver.
If a drive has Type 2 protection enabled (you frequently see this with
SAS drives shipped from Dell), don't set the various EEDP fields in the
mps(4)/mpr(4) driver command fields. Otherwise, you wind up with errors
like this that would otherwise make no sense:
(da9:mpr0:0:18:0): READ(10). CDB: 28 00 00 00 00 00 00 02 00 00
(da9:mpr0:0:18:0): CAM status: SCSI Status Error
(da9:mpr0:0:18:0): SCSI status: Check Condition
(da9:mpr0:0:18:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command operation code)
(da9:mpr0:0:18:0):
(da9:mpr0:0:18:0): Field Replaceable Unit: 0
(da9:mpr0:0:18:0): Command Specific Info: 0
(da9:mpr0:0:18:0):
(da9:mpr0:0:18:0): Descriptor 0x80: f8 21
(da9:mpr0:0:18:0): Descriptor 0x81: 00 00 00 00 00 00
(da9:mpr0:0:18:0): Error 22, Unretryable error
In other words, what kind of strange SAS hard drive doesn't support a
standard 10 byte SCSI READ command? In this case, one that has Type 2
protection enabled.
We can revisit this when we put Type 2 protection support in the da(4)
driver, but for now this will help people who put Type 2 formatted drives
in a system and wonder what in the world is going on.
MFC after: 3 days
Sponsored by: Spectra Logic
Version 16 is just a number bump, since we already had those changes.
Version 17 introduces new AdapterType value, that allows new user-space
tools from Broadcom to differentiate adapter generations 3 and 3.5.
Version 18 updates headers and adds SAS_DEVICE_DISCOVERY_ERROR reporting.
MFC after: 2 weeks
Chain frames required to satisfy all 2K of declared I/Os of 128KB each take
more then a megabyte of a physical memory, all of which existing code tries
allocate as physically contiguous. This patch removes that physical
contiguousness requirement, leaving only virtual contiguousness. I was
thinking about other ways of allocation, but the less granular allocation
becomes, the bigger is the overhead and/or complexity, reaching about 100%
overhead if allocate each frame separately.
The patch also bumps the chain frames hard limit from 2K to 16K. It is more
than enough for the case of default REQ_FRAMES and MAXPHYS (the drivers will
allocate less than that automatically), while in case of increased MAXPHYS
it will control maximal memory usage.
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D14420
