block. Use it in all the PNP drivers to export either the current PNP
table. For uart, create a custom table and export it using
MODULE_PNP_INFO since it's the only one that matches on function
number.
Differential Review: https://reviews.freebsd.org/D3461
1) Flag it and only access that command on the 3c1
2) The TX PLL appears to power down when not in use, so we have to power
it back up when we've been idle. Do this at the start of ifstart.
Otherwise we fall off the net.
o Grab the MAC address out of the CIS if the card has the special
3Com 0x88 tuple. Most 3Com cards don't have this tuple, but we
prefer it to the eeprom since it only appears to be present when
the eeprom doesn't have the info. So far, I've only observed this
on my 3C362 and 3C362B cards, but the NetBSD driver implies that
the 3C362C also has this tuple, and that some 3C574 cards do too (none
of mine do). ep_pccard_mac was written after looking at the NetBSD
code.
o Store the enet addr in the softc for this device, so we can use the
overridden MAC to set the station address.
o Create a routine to set the station address and use it where we need it.
o setup the cmd shitfs and such before we call ep_alloc(), and remove
setting up the cmd shift value there. It initializes to 0, and those
attachments that need to frob it do so before calling ep_alloc.
o Remove some obsolete comments
o No longer a need to export ep_get_macaddr, so make it static
o ep_alloc already grabs the EEPROM id, so we don't need to grab it again
in ep_pccard_attach.
o eliminate unit, it isn't needed, fix some printfs to be device_printf
instead.
# All my pccards except the 3C1 work now. Didn't test ISA or cbus cards
# that I have: 3C509B-TP or 3C569B-J-TPO
Tested on: 3C589B, 3C589C, 3C589D, 3C589D-TP, 3C562, 3C562B/3C563B,
3C562D/3C563D, 3CCFE574BT, 3CXEM556, 3CCSH572BT, 3C574-TX,
3CCE589EC, 3CXE589EC, 3CCFEM556, 3C1
Approved by: re (scottl)
which command to use to read the eeprom and which devices have an MII.
Simplify code by no longer using the OLDCARD compat rouintes (I don't
know if this breaks OLDCARD on pc98 or not, but OLDCARD on pc98 days
are numbered, I hope). This also removes a number of kludges that we
had before because they are OBE. Add a convenience routine to lookup
the device to avoid many casts in many places.
Tested with: 3C589D-TP, 3CCSH572BT
Approved by: re (scottl, blanket ep)
that says why we do this (or rather, explains that it is some voodoo magic
that's poorly understood). The local buffer fixes the crash on attach.
o Rename get_e() to ep_get_e() to avoid namespace pollution.
Submitted by: mux
Approved by: re (scottl)
Provide a backwards compatible way to have the extra macro by defining
PCCARD_API_LEVEL 5 before including pccarddevs for driver writers that
want/need to have the same driver on 5 and 6 with pccard attachments.
Approved by: re (dwhite)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
o Remove redundant $FreeBSD$
o Better comments about ep_get_macaddr.
o remove one tab in a switch statement (style only)
o Recognize ID 0x0035 as the device ID for the 3CXEM556 that I have. This
makes the 3CXEM556 work for me. Not 100% sure this is the assigned ID,
as I don't have the datasheets for this part, but it does work and get
the correct ethrnet address.
o Comment about the whole fake IRQ 3 thing. some need it, some don't, all
work with it.
Use EP_{READ,WRITE}{,_MULTI}_{1,2,4} instead. I've had several people
submit patches like this over the years of varying qualities, markm
being the last. The names were chosen in consulation with mdodd on
irc.
I've tested this with only PCMCIA cards: 3CCE589EC and 3CCSH572BT.
I've not tried with my more extensive ISA, EISA and cbus collection.
Reviewed by: mdodd
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
to match the pccard.conf file. There are more ID's that need adding, but
these seem to be the common ones.
This was committed on an ep0 interface under NEWCARD:
ep0: <3Com 3c589 10Mbps Ethernet> at port 0x300-0x30f irq 9 function 0 config 1 on pccard1
ep0: Ethernet address 00:10:4b:df:48:57
Reviewed by: imp
possible to have different probe/attach semantics between the two
systems and yet still use the same driver for both.
Compatibility methods for OLDCARD drivers. We use these routines to make
it possible to call the OLDCARD driver's probe routine in the context that
it expects. For OLDCARD these are implemented as pass throughs to the
device_{probe,attach} routines. For NEWCARD they are implemented such
such that probe becomes strictly a matching routine and attach does both
the old probe and old attach.
compat devices should use the following:
/* Device interface */
DEVMETHOD(device_probe), pccard_compat_probe),
DEVMETHOD(device_attach), pccard_compat_attach),
/* Card interface */
DEVMETHOD(card_compat_match, foo_match), /* newly written */
DEVMETHOD(card_compat_probe, foo_probe), /* old probe */
DEVMETHOD(card_compat_attach, foo_attach), /* old attach */
This will allow a single driver binary image to be used for both
OLDCARD and NEWCARD.
Drivers wishing to not retain OLDCARD compatibility needn't do this.
ep driver minorly updated.
sn driver updated more than minorly. Add module dependencies to allow
module to load. Also change name to if_sn. Add some debugging code.
attempt to fix the cannot allocate memory problem I'd been seeing.
Minor formatting nits.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
ifconfig and bogus ethernet address (4b:57:4b:57:4b:57) has been
hacked around. I'll revisit this when I have a clue whats going on.
Reviewed by: obrien
problem.
o Create new timeout routine so we don't detach the card inside a ISR
but instead drop back to spl0 via a timeout of 0.
o Actually delete the child of the pccard device rather than just faking
it badly.
o Fix sio, ed and ep to have pccard detach routines that are int rather
than void.
o Fix ep and ed pccard detach routines to use if_detach rather than just
if_down. if_detach destroys the device, while if_down just marks it
down. In this incarnation of the pccard things, we map the disable
the slot action to detach the driver, which removes the driver from the
device tree. When that is done, a panic would soon follow as the
ifconfig tried to down the device.
Didn't fix:
o Should cache the pccard dev child's pointer in struct slot
o remove now unused parts of struct slot
o Any driver using softc after detach has been called. sio's softc used
to be statically allocated, so you could check sc->gone, but that is
now gone.
o Didn't remove gone from softc of drivers that use the old pccard method.
Didn't test:
o ed driver changes
o sio driver changes on pccards
o suspend (no laptop or apm support on my desktop)
test this support since I don't have the dongle for the card in
question and the dongle I have for my 3C589D doesn't seem to work on
it. I don't know if this is due to the damage I did to the 562 card
in transit from freebsdcon, or a mis-matched dongle...
pccard attachments must activate the resources they want to access.
ep didn't do this, so of course thee eeprom came back as busy. ed and
sio already did this. It was only due to a bug in the logic that the
probe succeeded. These problems have been fixed.
- Rip out all the static softc stuff and do softc allocation the right way.
- Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY
method to enumerate all non-PnP ISA devices.
This has the following consequences:
- No 'ep' devices may be hardwired.
- All hardwired devices will probably be detected twice.
By hardwired I mean:
device ep0 at isa? port 0x300 irq 10
- 'ep' devices are ordered by bus, slot, and then MAC address.
- Make 3c509B cards work in PnP mode. Yes, they really work.
- Convert over to using ifmedia for media selection. No more of this
lame 'linkX' stuff.
- Consolidate a lot of duplicated code.
- Make a stab at not breaking MII based PCCARD devices.
I doubt that the PCCARD stuff works any more than it did before my
changes but theres hope. My PCCARD hardware should arrive in a
week or so.
- Retreive the media settings from the card EEPROM rather than guessing.
I've got a 3c509-TPO that thinks its got an AUI port and if others
can report similar problems I'll write a bit of clever code that will
fix this but right now it works correctly on all but 1 card.
- Clean up a few things and make some cosmetic changes.
- Add myself as the MAINTAINER since nobody else wants to. I'm
in the best position to do this as I've got an example of most
of the cards:
EISA 3c579 bnc/aui
MCA 3c529 tp/aui
ISA 3c509 tpo
ISA-PnP 3c509B combo
If someone wants to send me a any cards I don't have I'd appriciate
it. Also welcome are 3c59x boards since I'll be folding if_vx and
if_ep at some point.
