process is on the alternate stack or not. For compatibility
with sigstack(2) state is being updated if such is needed.
We now determine whether the process is on the alternate
stack by looking at its stack pointer. This allows a process
to siglongjmp from a signal handler on the alternate stack
to the place of the sigsetjmp on the normal stack. When
maintaining state, this would have invalidated the state
information and causing a subsequent signal to be delivered
on the normal stack instead of the alternate stack.
PR: 22286
-current and RELENG_4 with GENERIC.
NKPT is the number of initial bootstrap page table pages we create for
the kernel during startup. Once VM is up, we resize it as needed, but
with 4G ram, the size of the vm_page_t structures was pushing it over
the limit. The fact that trimmed down kernels boot on 4G ram machines
suggests that we were pretty close to the edge.
The "30" is arbitary, but smaller than the 'nkpt' variable on all
machines that I checked.
timeout. If DIAGNOSTIC is turned on, then display a message to the console
with a map of which CPUs failed to stop or restart. This gives an SMP box
at least a fighting chance of getting into DDB if one of the other CPUs has
interrupts disabled.
counter register in-CPU.
This is to be used as a fast "timer", where linearity is more important
than time, and multiple lines in the linearity caused by multiple CPUs
in an SMP machine is not a problem.
This adds no code whatsoever to the FreeBSD kernel until it is actually
used, and then as a single-instruction inline routine (except for the
80386 and 80486 where it is some more inline code around nanotime(9).
Reviewed by: bde, kris, jhb
- Use the mutex in hardclock to ensure no races between it and
softclock.
- Make softclock be INTR_MPSAFE and provide a flag,
CALLOUT_MPSAFE, which specifies that a callout handler does not
need giant. There is still no way to set this flag when
regstering a callout.
Reviewed by: -smp@, jlemon
may block on a mutex while on the sleep queue without corrupting
it.
- Move dropping of Giant to after the acquire of sched_lock.
Tested by: John Hay <jhay@icomtek.csir.co.za>
jhb
instead of DIAGNOSTIC.
- Remove the p_wchan check as it no longer applies since a process may be
switched out during CURSIG() within msleep() or mawait().
- Remove an extra sanity check only needed during the early SMPng work.
acquire Giant as needed in functions that call mi_switch(). The releases
need to be done outside of the sched_lock to avoid potential deadlocks
from trying to acquire Giant while interrupts are disabled.
Submitted by: witness
sched_lock. This is needed for kernel threads that are created before
interrupts are enabled. kthreads created by kld's that are created at
SI_SUB_KLD such as the random kthread.
Tested by: phk
syscall compare against a variable sv_minsigstksz in struct
sysentvec as to properly take the size of the machine- and
ABI dependent struct sigframe into account.
The SVR4 and iBCS2 modules continue to have a minsigstksz of
8192 to preserve behavior. The real values (if different) are
not known at this time. Other ABI modules use the real
values.
The native MINSIGSTKSZ is now defined as follows:
Arch MINSIGSTKSZ
---- -----------
alpha 4096
i386 2048
ia64 12288
Reviewed by: mjacob
Suggested by: bde
systems.
From the PR:
When 'probe.slot' is PCI_SLOTMAX (== 31) and 'probe.func' is 7,
call to 'pci_cfgread()' here and machine suddenly hangs up.
I don't know why... (or 450GX chipset's bug?)
PR: i386/20379
Submitted by: Masayuki FUKUI <fukui@sonic.nm.fujitsu.co.jp>
comments on the same line like so:
device foo # FooInc Brand NetEther cards
Also, move the wireless NIC cards to their own section.
Add commented out wl driver in wireless section.
Remove obsolete or redundant comments about some of the wireless cards
that used to apply but don't since we've removed 'at foobus'.
There should be no functional changes in this change.
happen when the vm system maps past the end of an object or tries
to map a zero length object, the pmap layer misses the fact that
offsets wrap into negative numbers and we get stuck.
Found by: Joost Pol aka Nohican <nohican@marcella.niets.org>
Submitted by: tegge
- Look for a hardwired interrupt in the routing table for this
bus/device/pin (we already did this).
- Look for another device with the same link byte which has a hardwired
interrupt.
- Look for a PCI device matching an entry with the same link byte
which has already been assigned an interrupt, and use that.
- Look for a routable interrupt listed in the "PCI only" interrupts
field and use that.
- Pick the first interrupt that's marked as routable and use that.
This removes support for booting current kernels with very old bootblocks.
Device driver writers: Please remove initializations for the d_bmaj
field in your cdevsw{}.
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.
Submitted by: cp
(a NetBSD port for NEC PC-98x1 machines). They are ncv for NCR 53C500,
nsp for Workbit Ninja SCSI-3, and stg for TMC 18C30 and 18C50.
I thank NetBSD/pc98 and bsd-nomads people.
Obtained from: NetBSD/pc98
reducues the maintenance load for the mutex code. The only MD portions
of the mutex code are in machine/mutex.h now, which include the assembly
macros for handling mutexes as well as optionally overriding the mutex
micro-operations. For example, we use optimized micro-ops on the x86
platform #ifndef I386_CPU.
- Change the behavior of the SMP_DEBUG kernel option. In the new code,
mtx_assert() only depends on INVARIANTS, allowing other kernel developers
to have working mutex assertiions without having to include all of the
mutex debugging code. The SMP_DEBUG kernel option has been renamed to
MUTEX_DEBUG and now just controls extra mutex debugging code.
- Abolish the ugly mtx_f hack. Instead, we dynamically allocate
seperate mtx_debug structures on the fly in mtx_init, except for mutexes
that are initiated very early in the boot process. These mutexes
are declared using a special MUTEX_DECLARE() macro, and use a new
flag MTX_COLD when calling mtx_init. This is still somewhat hackish,
but it is less evil than the mtx_f filler struct, and the mtx struct is
now the same size with and without mutex debugging code.
- Add some micro-micro-operation macros for doing the actual atomic
operations on the mutex mtx_lock field to make it easier for other archs
to override/optimize mutex ops if needed. These new tiny ops also clean
up the code in some places by replacing long atomic operation function
calls that spanned 2-3 lines with a short 1-line macro call.
- Don't call mi_switch() from mtx_enter_hard() when we block while trying
to obtain a sleep mutex. Calling mi_switch() would bogusly release
Giant before switching to the next process. Instead, inline most of the
code from mi_switch() in the mtx_enter_hard() function. Note that when
we finally kill Giant we can back this out and go back to calling
mi_switch().
in most of the atomic operations. Now for these operations, you can
use the normal atomic operation, you can use the operation with a read
barrier, or you can use the operation with a write barrier. The function
names follow the same semantics used in the ia64 instruction set. An
atomic operation with a read barrier has the extra suffix 'acq', due to
it having "acquire" semantics. An atomic operation with a write barrier
has the extra suffix 'rel'. These suffixes are inserted between the
name of the operation to perform and the typename. For example, the
atomic_add_int() function now has 3 variants:
- atomic_add_int() - this is the same as the previous function
- atomic_add_acq_int() - this function combines the add operation with a
read memory barrier
- atomic_add_rel_int() - this function combines the add operation with a
write memory barrier
- Add 'ptr' to the list of types that we can perform atomic operations
on. This allows one to do atomic operations on uintptr_t's. This is
useful in the mutex code, for example, because the actual mutex lock is
a pointer.
- Add two new operations for doing loads and stores with memory barriers.
The new load operations use a read barrier before the load, and the
new store operations use a write barrier after the load. For example,
atomic_load_acq_int() will atomically load an integer as well as
enforcing a read barrier.
write caching is disabled on both SCSI and IDE disks where large
memory dumps could take up to an hour to complete.
Taking an i386 scsi based system with 512MB of ram and timing (in
seconds) how long it took to complete a dump, the following results
were obtained:
Before: After:
WCE TIME WCE TIME
------------------ ------------------
1 141.820972 1 15.600111
0 797.265072 0 65.480465
Obtained from: Yahoo!
Reviewed by: peter
significantly pessimized syscalls by arranging to do null rescheduling
on return from every syscall. (AST_RESCHED was not defined, and the
mask ~AST_RESCHED gets replaced by the useless mask ~0. This bug has
been fixed before, in rev.1.92.)
check in the [basic.link] section of the C++ standard wrong. gcc-2.7.2.3
apparently doesn't do the check, so the bug doesn't affect RELENG_3.
PR: 16170, 21427
Submitted by: Max Khon <fjoe@lark.websci.ru> (i386 version)
Discussed with: jdp
return through doreti to handle ast's. This is necessary for the
clock interrupts to work properly.
- Change the clock interrupts on the x86 to be fast instead of threaded.
This is needed because both hardclock() and statclock() need to run in
the context of the current process, not in a separate thread context.
- Kill the prevproc hack as it is no longer needed.
- We really need Giant when we call psignal(), but we don't want to block
during the clock interrupt. Instead, use two p_flag's in the proc struct
to mark the current process as having a pending SIGVTALRM or a SIGPROF
and let them be delivered during ast() when hardclock() has finished
running.
- Remove CLKF_BASEPRI, which was #ifdef'd out on the x86 anyways. It was
broken on the x86 if it was turned on since cpl is gone. It's only use
was to bogusly run softclock() directly during hardclock() rather than
scheduling an SWI.
- Remove the COM_LOCK simplelock and replace it with a clock_lock spin
mutex. Since the spin mutex already handles disabling/restoring
interrupts appropriately, this also lets us axe all the *_intr() fu.
- Back out the hacks in the APIC_IO x86 cpu_initclocks() code to use
temporary fast interrupts for the APIC trial.
- Add two new process flags P_ALRMPEND and P_PROFPEND to mark the pending
signals in hardclock() that are to be delivered in ast().
Submitted by: jakeb (making statclock safe in a fast interrupt)
Submitted by: cp (concept of delaying signals until ast())
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
device_add_child() is meant to be called by the bus add_child method, not
to replace the bus add_child method. We could have called nexus_add_device
directly too, that would have also worked.
PR: 21657
Tested by: markm
- Move all register I/O into acpi_io.c
- Move event handling into acpi_event.c
- Reorganise headers into acpivar/acpireg/acpiio
- Move find-RSDT and find-ACPI-owned-memory into acpi_machdep
- Allocate all resources (except those detailed only by AML)
as real resources. Add infrastructure that will make adding
resource support to AML code easy.
- Remove all ACPI #ifdefs in non-ACPI code
- Removed unnecessary includes
- Minor style and commenting fixes
Reviewed by: iwasaki
to accomodate the changes.
Here's a list of things that have changed (I may have left out a few); for a
relatively complete list, see http://people.freebsd.org/~bmilekic/mtx_journal
* Remove old (once useful) mcluster code for MCLBYTES > PAGE_SIZE which
nobody uses anymore. It was great while it lasted, but now we're moving
onto bigger and better things (Approved by: wollman).
* Practically re-wrote the allocation macros in sys/sys/mbuf.h to accomodate
new allocations which grab the necessary lock.
* Make sure that necessary mbstat variables are manipulated with
corresponding atomic() routines.
* Changed the "wait" routines, cleaned it up, made one routine that does
the job.
* Generalized MWAKEUP() macro. Got rid of m_retry and m_retryhdr, as they
are now included in the generalized "wait" routines.
* Sleep routines now use msleep().
* Free lists have locks.
* etc... probably other stuff I'm missing...
Things to look out for and work on later:
* find a better way to (dynamically) adjust EXT_COUNTERS
* move necessity to recurse on a lock from drain routines by providing
lock-free lower-level version of MFREE() (and possibly m_free()?).
* checkout include of mutex.h in sys/sys/mbuf.h - probably violating
general philosophy here.
The code has been reviewed quite a bit, but problems may arise... please,
don't panic! Send me Emails: bmilekic@freebsd.org
Reviewed by: jlemon, cp, alfred, others?
not work on any real hardware (or fully work on any simulator). Much more
needs to happen before this is actually functional but its nice to see
the FreeBSD copyright message appear in the ia64 simulator.
i386/isa/pcibus.c. This gets -current running again on multiple host->pci
machines after the most recent nexus commits. I had discussed this with
Mike Smith, but ended up doing it slightly differently to what we
discussed as it turned out cleaner this way. Mike was suggesting creating
a new resource (SYS_RES_PCIBUS) or something and using *_[gs]et_resource(),
but IMHO that wasn't ideal as SYS_RES_* is meant to be a global platform
property, not a quirk of a given implementation. This does use the ivar
methods but does so properly. It also now prints the physical pci bus that
a host->pci bridge (pcib) corresponds to.
Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
thread for each interrupt that comes in. If we don't, log the event and
return immediately for a hardware interrupt. For a softinterrupt, panic
instead.
Submitted by: ben
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
in the boot. The cleanup must be done in one of the few ways that
db_numargs() understands, so that early backtraces in ddb don't underrun
the stack. The underruns caused reboots a few years ago when there
was an unmapped page above the stack (trapping to abort the command
doesn't work early).
Cleaned up some nearby code.
curproc was initialized. curproc == NULL was interpreted as matching
the process holding Giant... Just skip mtx_enter() and mtx_exit() in
trap() if (curproc == NULL && cold) (&& cold for safety).
don't take an arg, but swi_generic() is special in order to avoid one
whole conditional branch in the old SWI dispatch code. The new SWI
dispatch code passed it a garbage arg. Bypass swi_generic() and call
swi_dispatcher() directly, like the corresponding alpha code has always
done.
The panic was rare because because it only occurred if more than one
of the {sio,cy,rc} drivers was configured and one was active, and the
cy driver doesn't even compile.
macros that expand to pass filename and line number information. This is
necessary since we're using inline functions instead of macros now.
Add const to the filename pointers passed througout the mtx and witness
code.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
Some have dual host->PCI bridges for the same logical pci bus (!), eg:
some of the RCC chipsets. This is a 32/64 bit 33/66MHz and dual pci
voltage motherboard so persumably there are electical or signalling
differences but they are otherwise the same logical bus.
The new PCI probe code however was getting somewhat upset about it and
ended up creating two pci bridges to the same logical bus, which caused
devices on that logical bus to appear and be probed twice.
The ACPI data on this box correctly identifies this stuff, so bring on
ACPI! :-)
This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
pcib_set_bus() cannot be used on the new child because it is
meant to be used on the *pci* device (it looks at the parent internally)
not the pcib being added. Bite the bullet and use ivars for the bus
number to avoid any doubts about whether the softc is consistant between
probe and attach. This should not break the Alpha code.
- Enable WB cache via CCR2 and CR0.
- Set the need_pre_dma_flush when the CPU_I486_ON_386 option is
defined.
Submitted by: Kaho Toshikazu <kaho@elam.kais.kyoto-u.ac.jp>
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
Remove old DEVFS support fields from dev_t.
Make uid, gid & mode members of dev_t and set them in make_dev().
Use correct uid, gid & mode in make_dev in disk minilayer.
Add support for registering alias names for a dev_t using the
new function make_dev_alias(). These will show up as symlinks
in DEVFS.
Use makedev() rather than make_dev() for MFSs magic devices to prevent
DEVFS from noticing this abuse.
Add a field for DEVFS inode number in dev_t.
Add new DEVFS in fs/devfs.
Add devfs cloning to:
disk minilayer (ie: ad(4), sd(4), cd(4) etc etc)
md(4), tun(4), bpf(4), fd(4)
If DEVFS add -d flag to /sbin/inits args to make it mount devfs.
Add commented out DEVFS to GENERIC
that should be better.
The old code counted references to mbuf clusters by using the offset
of the cluster from the start of memory allocated for mbufs and
clusters as an index into an array of chars, which did the reference
counting. If the external storage was not a cluster then reference
counting had to be done by the code using that external storage.
NetBSD's system of linked lists of mbufs was cosidered, but Alfred
felt it would have locking issues when the kernel was made more
SMP friendly.
The system implimented uses a pool of unions to track external
storage. The union contains an int for counting the references and
a pointer for forming a free list. The reference counts are
incremented and decremented atomically and so should be SMP friendly.
This system can track reference counts for any sort of external
storage.
Access to the reference counting stuff is now through macros defined
in mbuf.h, so it should be easier to make changes to the system in
the future.
The possibility of storing the reference count in one of the
referencing mbufs was considered, but was rejected 'cos it would
often leave extra mbufs allocated. Storing the reference count in
the cluster was also considered, but because the external storage
may not be a cluster this isn't an option.
The size of the pool of reference counters is available in the
stats provided by "netstat -m".
PR: 19866
Submitted by: Bosko Milekic <bmilekic@dsuper.net>
Reviewed by: alfred (glanced at by others on -net)
suggested fix in PR 12378.
Keep track of all existing pmaps independent of existing processes.
This allows for a process to temporarily connect to a different address
space without the risk of missing an update of the original address space if
the kernel grows.
pmap_pinit2() is no longer needed on the i386 platform but is left as a
stub until the alpha pmap code is updated.
PR: 12378
- stop using the evil 'struct trapframe' argument for mi_startup()
(formerly main()). There are much better ways of doing it.
- do not use prepare_usermode() - setregs() in execve() will do it
all for us as long as the p_md.md_regs pointer is set. (which is
now done in machdep.c rather than init_main.c. The Alpha port did it
this way all along and is much cleaner).
- collect all the magic %cr0 etc register settings into one place and
have the AP's call that instead of using magic numbers (!!) that keep
changing over and over again.
- Make it safe to call kthread_create() earlier, including during the
device probe sequence. It doesn't need the callback mechanism that
NetBSD's version uses.
- kthreads created this way are root-less as they exist before the root
filesystem is mounted. init(1) is set up so that it aquires the root
pointers prior to running. If other kthreads want filesystem acccess
we can make this code more generic.
- set all threads start times once we have decided what time it is.
- init uses a trampoline rather than the evil prepare_usermode() hack.
- kern_descrip.c has a couple of tweaks to deal with forking when there
is no rootdir or cwd etc.
- adjust the early SYSINIT() sequence so that a few prereqisites are in
place. eg: make sure the run queue is initialized before doing forks.
With this, the USB code can easily create a kthread to do the device
tree discovery. (I have tested it, it works nicely).
There are still some open issues before this is truely useful.
- tsleep() does not like working before the clock is running. It
sort-of tries to spin wait, but it can do more useful things now.
- stopping a kthread in kld code at unload time is "interesting" but
we have a solution for that.
The Alpha code needs no changes for this. It already uses pretty much the
same strategies, but a little cleaner.
With more than 1 AP present, an AP could fail to properly release
the mp lock before waiting for smp_started to become nonzero.
With early startup of APs, the BSP could fail to properly release
the mp lock before waiting for smp_started to become nonzero.
panicing and return a status so that we can decide whether to drop
into DDB or panic. If the status from isa_nmi is true, panic the
kernel based on machdep.panic_on_nmi, otherwise if DDB is
enabled, drop to DDB based on machdep.ddb_on_nmi.
Reviewed by: peter, phk
Don't allow cpu entries in the MP table to contain APIC IDs out of range.
Don't write outside array boundaries if an IO APIC entry in the MP table
contains an APIC ID out of range.
Assign APIC IDs for all IO APICs according to section 3.6.6 in the
Intel MP spec:
- If the current APIC ID on an IO APIC doesn't conflict with other
IO APICs or CPUs, that APIC ID should be used. The copy of the MP
table must be updated if the corresponding APIC ID in the MP table
is different.
- If the current APIC ID was in conflict with other units, the
corresponding APIC ID specified in the MP table is checked for conflict.
- If a conflict is still found then fall back to using a new unique ID.
The copy of the MP table must be updated.
- IDs out of range is considered to be in conflict.
During these operations, the IO_TO_ID array cannot be used, since any
conflict would have caused information loss. The array is then corrected,
since all APIC ID conflicts should have been resolved.
PR: 20312, 18919
due to a paucity of IRQs. I have some reservations about this, so I'm
not going to MFC this just yet. I'm doing this to see how many
problems it causes so we can do this in 4.2. I've been seeing hangs
on my laptop from time to time, but sometimes it was not in polling
mode, other tmies it was. Don't know if this is one problem or more
than one.
Requested by: Sean O Connell
a NMI occured, you could type continue in DDB and the kernel would
not attempt to detect what type of NMI was recieved. Now we check
for the type of NMI first and then go to DDB if it is enabled.
This will solve the problem with having DDB enabled and getting an
NMI due to some possibly bad error and being able to continue the
operation of the kernel when you really want to panic and know
what happened.
Submitted by: jhb
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
the PnP probe is merely a stub as we make assumptions about some of this
hardware before we have probed it.
Since these devices (with the exception of the speaker) are 'standard',
suppress output in the !bootverbose case to clean up the probe messages
somewhat.
need this RSN.
Remove a pointless warning in the root device locating code.
Remove the "wd" compatibility name from the "ad" driver.
WARNING: If you have not updated to use /dev/wd* in your /etc/fstab
and modern bootblocks, it would be a very good idea to do so BEFORE
you upgrade your kernel.
errors were normally harmless because they were in unreachable code
and gcc apparently doesn't check the syntax inside asm statements
that it optimizes away.
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.
config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel. You can reconfigure your
isa devices with the likes of this at loader(8) time:
set hint.ed.0.port=0x320
userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.
It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8). See the "hints" directive in GENERIC
as an example.
All device wiring has been moved out of config(8). There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file. If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you. You can also compile in the
hints directly with: hints "device.hints" as well.
There are a few things that I'm not too happy with yet. Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it. However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built. A stack of man4 pages will need updating. :-/
Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated. eg: 'device fe 4' will compile the fe driver with NFE set
to 4. You can then set hints for 4 units (0 - 3). Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this. This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.
Please exercise EXTREME CAUTION when transitioning!
Moral support by: phk, msmith, dfr, asmodai, imp, and others
Socket 8 to 370 converters. When (1) CPU_PPRO2CELERON option is
defined, (2) Intel CPU is found and (3) CPU ID is 0x66?, L2 cache is
enabled through MSR 0x11e. The L2 cache latency value can be
specified by CPU_L2_LATENCY option. Default value of L2 cache latency
is 5.
These options are useful if you use Socket 8 to Socket 370 converter
(e.g. Power Leap's PL-Pro/II.) Most PentiumPro BIOSs don't enable L2
cache of Mendocino Celeron CPUs because they don't know Celeron CPUs.
These options are needles if you use a Coppermine (FCPGA) Celeron or
PentiumIII, becuase the L2 cache enable bit is hard wired and L2 cache
is always enabled.
end values in bootinfo) in kernel space if it is loaded (i.e., if its
specified end address is nonzero), not just if it is loaded and DDB
is configured. This may be used to fix kldsym(2) for booting without
/dev/loader; currently, in this case, it just fixes unused pointers
and wastes space consistently. For booting in the normal way with
/boot/loader, the table is included and pointed to in a different way
and kldsym(2) works.
