frame buffers and memory mapped UARTs.
1. Delay calling cninit() until after pmap_bootstrap(). This makes
sure we have PMAP initialized enough to add translations. Keep
kdb_init() after cninit() so that we have console when we need
to break into the debugger on boot.
2. Unfortunately, the ATPIC code had be moved as well so as to
avoid a spurious trap #30. The reason for which is not known
at this time.
3. In pmap_mapdev_attr(), when we need to map a device prior to the
VM system being initialized, use virtual_avail as the KVA to map
the device at. In particular, avoid using the direct map on amd64
because we can't demote by virtue of not being able to allocate
yet. Keep track of the translation.
Re-use the translation after the VM has been initialized to not
waste KVA and to satisfy the assumption in uart(4) that the handle
returned for the low-level console is the same as later returned
when the device is probed and attached.
4. In pmap_unmapdev() remove the mapping from the table when called
pre-init. Otherwise keep the mapping. During bus probe and attach
device resources are mapped and unmapped multiple times, which
would have us destroy the mapping used by the low-level console.
5. In pmap_init(), set pmap_initialized to signal that we're not
pre-init anymore. On amd64, bring the direct map in sync with the
translations created at that time.
6. Implement bus_space_map() and bus_space_unmap() for real: when
the tag corresponds to memory space, call the corresponding
pmap_mapdev() and pmap_unmapdev() functions to construct and
actual handle.
7. In efifb.c and vt_vga.c, remove the crutches and hacks and simply
call pmap_mapdev_attr() or bus_space_map() as desired.
Notes:
1. uart(4) already used bus_space_map() during low-level console
setup but since serial ports have traditionally been I/O port
based, the lack of a proper implementation for said function
was not a problem. It has always supported memory mapped UARTs
for low-level consoles by setting hw.uart.console accordingly.
2. The use of the direct map on amd64 without setting caching
attributes has been a bigger problem than previously thought.
This change has the fortunate (and unexpected) side-effect of
fixing various EFI frame buffer problems (though not all).
PR: 191564, 194952
Special thanks to:
1. XipLink, Inc -- generously donated an Intel Bay Trail E3800
based eval board (ADLE3800PC).
2. The FreeBSD Foundation, in particular emaste@ -- for UEFI
support in general and testing.
3. Everyone who tested the proposed for PR 191564.
4. jhb@ and kib@ for being a soundboard and applying a clue bat
if so needed.
define GID_VIDEO in sys/conf.h, and use it together with UID_ROOT
to define DRM_DEV_UID and DRM_DEV_GID in the drmP.h files.
So there is one place where the UID's and GID's are defined.
Submitted by: ed@
Reviewed by: ed@, dumbbell@
Differential Revision: https://reviews.freebsd.org/D3360
can be seen as the same as 0.2. There are changes with the data passed to
CPU_SUSPEND, however we don't yet use this call.
Sponsored by: ABT Systems Ltd
electrical signals on the serial port. Virtually all devices which output a
PPS signal generate a brief higher-voltage pulse, the leading edge of which
is the on-time point.
Both DCD and CTS are active-low signals on the wire, meaning the assertion
of their status bits in the modem status register corresponds to the lower
voltage level on the wire. So when the status bit transitions to not-set,
create a PPS assert event; when the status bit transitions to set, create a
PPS clear event.
eliminating the need to build a custom kernel to use the CTS signal.
The historical UART_PPS_ON_CTS kernel option is still honored, but now it
can be overridden at runtime using a tunable to configure all uart devices
(hw.uart.pps_mode) or specific devices (dev.uart.#.pps_mode). The per-
device config is both a tunable and a writable sysctl.
This syncs the PPS capabilities of uart(4) with the enhancements recently
recently added to ucom(4) for capturing from USB serial devices.
Relnotes: yes
devices in /dev/dri/ with this new group.
This will allow ports and users to more easily access to these devices
for OpenGL and OpenCL support.
Reviewed by: dumbbell@
Approved by: dumbbell@
Differential Revision: https://reviews.freebsd.org/D1260
Internal bridges in Cavium ThunderX SoC behave as subtractive,
but they are unable to be identified. Force setting an appropriate
flag.
Reviewed by: emaste, imp
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3277
time_pps_fetch() to be used in blocking mode.
Also, don't init the pps api for system devices (consoles) that provide a
custom attach routine. The device may actually be a keyboard or other non-
tty device. If it wants to do pps processing (unlikely) it must handle
everything for itself. (In reality, only a sun keyboard uses a custom
attach routine, and it doesn't make a good pps device.)
For some reason 32-bit PIO writes are not working on 6Gbit/s Intel SATA
ports, while 16/32-bit PIO reads and 16-bit PIO writes are working fine.
3Gbit/s ports on the same controllers have no this problem.
Workaround this by disabling 32-bit PIO for all Intel controllers that may
have 6Gbit/s ports. It halves PIO performance from 6MB/s to 3MB/s, but
who bother about speed of such rare and slow mode, which is also highly
discouraged by SATA specifications?
MFC after: 2 weeks
There are still several bugs, but I've been using it for a while now.
Thanks to all the testers and to Adrian for his help with this
driver.
This driver isn't connected to the build yet, but it will be soon.
There's no MFC planned because the driver isn't very stable yet.
Reviewed by: adrian
Obtained from: https://github.com/rpaulo/iwm
Tested by: adrian, gjb, dumbbell (others that I forgot).
Relnotes: yes
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
Main problem there was PIO mode support, that required KVA mapping.
Handle that case using recently added pmap_quick_enter_page(9) KPI,
mapping data pages to KVA one at a time.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
The ftdi chip itself has a "get bitmode" command that doesn't actually
return the current bitmode, just a snapshot of the gpio lines. The chip
apparently has no way to provide the current bitmode.
This implements the functionality at the driver level. The driver starts
out assuming the chip is in UART mode (which it will be, coming out of
reset) and keeps track of every successful set-bitmode operation so that
it can always return the current mode with UFTDIIOC_GET_BITMODE.
use vtophys() directly instead of vtomach() and retire the no-longer-used
headers <machine/xenfunc.h> and <machine/xenvar.h>.
Reported by: bde (stale bits in <machine/xenfunc.h>)
Reviewed by: royger (earlier version)
Differential Revision: https://reviews.freebsd.org/D3266
is detaching.
This mostly fixes a panic - the reset path shouldn't run whilst
the NIC is being torn down.
It's not locked, so it's "mostly" ok, but most of the rest of
the driver doesn't read sc->invalid with sensible locking. Grr.
The real solution is to cleanly tear down taskqueues in the detach/suspend
phase, but ..
changes in the firmwares since 1.11.27.0 are listed here (straight copy-paste
from the "Release Notes.txt" accompanying the Chelsio Unified Wire 2.11.1.0
release on the website).
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.14.4.0
Date : 08/05/2015
================================================================================
FIXES
-----
BASE:
- Fixes a potential data path hang by properly programming PMTX congestion
threshold settings.
- Fixes a potential initialization error when accessing a configuration file
stored on the flash.
- Fixes a regression where SGE resources can be miss-sized if iWARP is disabled.
ETH:
- Fixes a timing issue that would prevent CR4 links from coming up with some
switches.
FOFCoE:
- Defers fcoe linkdown mailbox command handling till LOGO is sent.
- Updates vlan prio for all outstanding IOs during dcbx update.
ENHANCEMENTS
------------
BASE:
- Adds support for PAUSE OFF watchdog.
- Reports devlog access information in PCIE_FW_PF register 7.
ETH:
- Enhances segmentation offload to include VxLAN and Geneve.
- Adds PTP support.
- Adds new interface to allow the driver to query the VI rss table base
addresses.
- Allows the driver to program the SGE ingrext contxt CongDrop field.
OFLD:
- Adds new interface for the driver to specify offloaded connections TCP snd
and rcv scale factors.
iSCSI:
- Adds support for iscsi segmentatation offload (ISO).
- Adds support for iscsi t10-dif offload.
FOiSCSI:
- Sets FORCE_BIT for cut through processing for FOiSCSI.
FOFCoE:
- Adds support for FCoE BB6.
- Improves WRITE performance.
================================================================================
================================================================================
Version : 1.13.32.0
Date : 03/25/2015
================================================================================
FIXES
-----
BASE:
- Fixes FW_CAPS_CONFIG_CMD return value on error (was positive instead of
negative)
- Fixes FW_PARAMS_PARAM_DEV_FLOWC_BUFFIFO_SZ indication (was wrong on certain
adapter configurations)
- Fixes config file based PL_TIMEOUT register programming
ETH:
- Fixes a potential EO UDP SEG header corruption
- Fixes an issue where 1000Base-X was not enabled correctly when using QSA
modules
OFLD:
- Fixes timeout issue with half-open connections
- Fixes FW_FLOWC_WR processing when state is set to finwait1
FOFCoE:
- Fixes fcoe xchg leaks in linkdown/peer down path
- Fixes cleanup in FCoE linkdown and fixed buf timer flowid abuse
- Fixes fw crash by clearing fcf flowc during bye
FOiSCSI:
- Don't create a new tcp socket if ERL0 attempt has timed out.
ENHANCEMENTS
------------
BASE:
- Adds support for VFs on PFs 4 to 7
- Adds support for QPs/CQs on any physical and virtual function
ETH:
- Stops sending LACP frames on loopback interface
- Adds an AUTOEQU indication to CPL_SGE_EGR_UPDATE
- Adds support for CR4 links (BEAN/AEC on 40G TwinAx cables)
OFLD:
- Improves default settings of LAN and CLUSTER TCP timer settings
- Sends Negative Advice CPLs to software
FOISCSI:
- Adds IPv6 support for foiscsi. Keeps backward compatibility with
old foiscsi drivers which doesn't support ipv6.
FOFCoE:
- Added fcoe debug support in flowc dump
================================================================================
================================================================================
Version : 1.12.25.0
Date : 10/22/2014
================================================================================
FIXES
-----
BASE:
- Improves precision of the Weight Round Robing Traffic Management Algorithm
- Fixes an issue where the link would intermittently fail to come up
- Fixes an issue where adapters with an external PHY couldn't run at 100Mbps
- Fixes an issue where active optical cables were not recognized
- Fixes link advertising issues on T520-BT (speed and pause frames) that would
cause the link to negotiate unexpected settings
- Forces link restart when auto-negotiation is disabled
- Fix an issue where pause frames wouldn't be fully disabled even if requested
ETH:
- Fixes NVGRE Segmentation Offload network header generation.
DCBX:
- Fixes an issue where some settings were not being sent to the switch
correctly
- Fixes an issue where back-to-back DCBX port updates could get overwritten by
FW
- Fixes a firmware crash on DCBX APP information request before link up
FOiSCSI:
- Fixes abort task leak in tmf response handling
- Fixes TCP RST handling while in iSCSI ERL0
- Fixes a firmware crash on BYE without INIT
ENHANCEMENTS
-------------
BASE:
- Adds link partner settings reporting when available
- Adds QSA support (in conjunction with QSA VPD)
- Adds T520-BT LED support
- Reports NOTSUPPORTED for modules with an unhandled identifier
DCBX:
- Adds version reporting (indicating which version FW is trying to negotiate)
- Adds IEEE support
- Reports LLDP time outs
FOiSCSI:
- Add support for multiple iSCSI DDP client
- Sends DHCP renew request when lease expires
================================================================================
22.2. T4 Firmware
+++++++++++++++++
Version : 1.14.4.0
Date : 08/05/2015
================================================================================
FIXES
-----
BASE:
- Fixes a potential initialization error when accessing a configuration file
stored on the flash.
- Initialize PCIE_DBG_INDIR_REQ.Enable to 0, as hardware failed to do so and
register dumps could result in errors.
ETH:
- Fixes an issue that sometimes prevented the link from coming up in CR adapters.
ENHANCEMENTS
------------
BASE:
- Adds support for PAUSE OFF watchdog.
- Reports devlog access information in PCIE_FW_PF register 7.
ETH:
- Adds new interface to allow the driver to query the VI rss table base
addresses.
OFLD:
- Adds new interface for the driver to specify offloaded connections TCP snd
and rcv scale factors.
================================================================================
================================================================================
Version : 1.13.32.0
Date : 03/25/2015
================================================================================
FIXES
-----
BASE:
- Fixes FW_CAPS_CONFIG_CMD return value on error (was positive instead of
negative)
- Fixes FW_PARAMS_PARAM_DEV_FLOWC_BUFFIFO_SZ indication (was wrong on certain
adapter configurations)
- Fixes config file based PL_TIMEOUT register programming
ETH:
- Fixes a potential EO UDP SEG header corruption
OFLD:
- Fixes timeout issue with half-open connections
- Fixes FW_FLOWC_WR processing when state is set to finwait1
FOiSCSI:
- Don't create a new tcp socket if ERL0 attempt has timed out.
ENHANCEMENTS
------------
ETH:
- Stops sending LACP frames on loopback interface
- Adds an AUTOEQU indication to CPL_SGE_EGR_UPDATE
OFLD:
- Improves default settings of LAN and CLUSTER TCP timer settings
- Sends Negative Advice CPLs to software
================================================================================
================================================================================
Version : 1.12.25.0
Date : 10/22/2014
================================================================================
FIXES
-----
BASE:
- Improves precision of the Weight Round Robing Traffic Management Algorithm
- Forces link restart when auto-negotiation is disabled
- Fix an issue where pause frames wouldn't be fully disabled even if requested
DCBX:
- Fixes an issue where some settings were not being sent to the switch
correctly
- Fixes an issue where back-to-back DCBX port updates could get overwritten by
FW
- Fixes a firmware crash on DCBX APP information request before link up
FOiSCSI:
- Fixes abort task leak in tmf response handling
- Fixes TCP RST handling while in iSCSI ERL0
- Fixes a firmware crash on BYE without INIT
ENHANCEMENTS
------------
BASE:
- Adds link partner settings reporting when available
- Firmware now reports NOTSUPPORTED for modules with an unhandled identifier
DCBX:
- Adds version reporting (indicating which version FW is trying to negotiate)
- Adds IEEE support
- Reports LLDP time outs
FOiSCSI:
- Adds support for multiple iSCSI DDP clients
- Sends DHCP renew request when lease expires
================================================================================
Obtained from: Chelsio Communications
MFC after: 2 weeks
Sponsored by: Chelsio Communications
- The existing TCP INP_INFO lock continues to protect the global inpcb list
stability during full list traversal (e.g. tcp_pcblist()).
- A new INP_LIST lock protects inpcb list actual modifications (inp allocation
and free) and inpcb global counters.
It allows to use TCP INP_INFO_RLOCK lock in critical paths (e.g. tcp_input())
and INP_INFO_WLOCK only in occasional operations that walk all connections.
PR: 183659
Differential Revision: https://reviews.freebsd.org/D2599
Reviewed by: jhb, adrian
Tested by: adrian, nitroboost-gmail.com
Sponsored by: Verisign, Inc.
hangs on shutdown with LUNs with mounted filesystems over a disconnected
iSCSI session.
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3052
to double check for if the card has probed before. In fact, there's no
reason to single check either. Simplify the code as a result.
$FreeBSD$ added to lxutil.c in a non-standard way to help keep the
diffs with upstream to a minimum.
Differential Revision: https://reviews.freebsd.org/D3263
Brightness is controlled through sysctl dev.gpiobacklight.X.brightness:
- any value greater than 0: backlight is on
- any value less than or equal to 0: backlight is off
FDT bindings docs in Linux tree:
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt
the blkfront driver to perform I/Os of up to 2 MB, subject to support from
the blkback to which it is connected and the initiation of such large I/Os
by the rest of the kernel. In practice, the I/O size is increased from 40 kB
to 128 kB.
The changes to xen/interface/io/blkif.h consist merely of merging updates
from the upstream Xen repository.
In dev/xen/blkfront/block.h we add some convenience macros and structure
fields used for indirect-page I/Os: The device records its negotiated limit
on the number of indirect pages used, while each I/O command structure gains
permanently allocated page(s) for indirect page references and the Xen grant
references for those pages.
In dev/xen/blkfront/blkfront.c we now check in xbd_queue_cb whether a request
is small enough to handle without an indirection page, and either follow the
previous behaviour or use new code for issuing an indirect segment I/O. In
xbd_connect we read the size of indirect segment I/Os supported by the backend
and select the maximum size we will use; then allocate the pages and Xen grant
references for each I/O command structure. In xbd_free those grants and pages
are released.
A new loader tunable, hw.xbd.xbd_enable_indirect, can be set to 0 in order to
disable this functionality; it works by pretending that the backend does not
support this feature. Some backends exhibit a loss of performance with large
I/Os, so users may wish to test with and without this functionality enabled.
Reviewed by: royger
MFC after: 3 days
Relnotes: yes
Both are used to protect access to IP addresses lists and they can be
acquired for reading several times per packet. To reduce lock contention
it is better to use rmlock here.
Reviewed by: gnn (previous version)
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D3149
While here, reduce the style diff with Linux.
There is no functional change. The goal is to ease the future update to
Linux 3.8's i915 driver.
MFC after: 2 months
enqueueing the frames when it fails. This way there is some latency
removed from the transmitting path.
- If IFF_DRV_OACTIVE is set (and also if IFF_DRV_RUNNING is not) just
enqueue the desired frames and return successful transmit. This way we
avoid to return errors on transmit side and resulting in
possible out-of-order frames. Please note that IFF_DRV_OACTIVE is set
everytime we get the threshold ring hit, so this can be happening quite
often.
Submitted by: Attilio.Rao@isilon.com
MFC after:5 days
On some platforms, the /cpus node contains cpu-to-cluster
map which deffinitely is not a CPU node. Its presence was
causing incrementing of "id" variable and reporting more
CPUs available than it should.
To make "id" valid, increment it only when an entry really
is a CPU device.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3216
Remove NAKing limit and pause IN and OUT transactions for 125us in
case of NAK response for BULK and CONTROL endpoints. This gets the
receive latency down and improves USB network throughput at the cost
of some CPU usage.
MFC after: 1 month
xhci_start_controller() to xhci_init(). These values don't change at run-
time so there's no point of acquiring them on every USB_HW_POWER_RESUME
instead of only once during initialization. In r276717, reading the first
couple of registers in question already had been moved as a prerequisite
for the changes in that revision.
- Identify ASMedia ASM1042A controllers.
- Use NULL instead of 0 for pointers.
MFC after: 3 days
