here any more as they are self identifying. Only PNP remains but that
will be replaced any day now.
Also reword a comment that had been XXX'ed to death to make it clear[er]
why we don't enable interrupts before probing.
PCIBIOS interrupt routing controls may make this possible to fix one day.
than having explicit hooks here.
Treat the eisa/isa attach a little differently so that we defer the
decision about to attach eisa/isa to the motherboard directly only if
the PCI probe (if it exists) fails to turn up a PCI->EISA/ISA bridge.
This restores the original device geometry where ISA and/or EISA attach
to their bridge rather than bypassing and going to the root.
`sleep 1; zzz' trick now.
- APM BIOS Call for suspend/standby now should be issued with delay.
- Delay for suspend/standby can be adjusted by using sysctl(8) interface
(eg. sysctl -w machdep.apm_suspend_delay=3).
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
MII-compliant PHY drivers. Many 10/100 ethernet NICs available today
either use an MII transceiver or have built-in transceivers that can
be programmed using an MII interface. It makes sense then to separate
this support out into common code instead of duplicating it in all
of the NIC drivers. The mii code also handles all of the media
detection, selection and reporting via the ifmedia interface.
This is basically the same code from NetBSD's /sys/dev/mii, except
it's been adapted to FreeBSD's bus architecture. The advantage to this
is that it automatically allows everything to be turned into a
loadable module. There are some common functions for use in drivers
once an miibus has been attached (mii_mediachg(), mii_pollstat(),
mii_tick()) as well as individual PHY drivers. There is also a
generic driver for all PHYs that aren't handled by a specific driver.
It's possible to do this because all 10/100 PHYs implement the same
general register set in addition to their vendor-specific register
sets, so for the most part you can use one driver for pretty much
any PHY. There are a couple of oddball exceptions though, hence
the need to have specific drivers.
There are two layers: the generic "miibus" layer and the PHY driver
layer. The drivers are child devices of "miibus" and the "miibus" is
a child of a given NIC driver. The "miibus" code and the PHY drivers
can actually be compiled and kldoaded as completely separate modules
or compiled together into one module. For the moment I'm using the
latter approach since the code is relatively small.
Currently there are only three PHY drivers here: the generic driver,
the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding
others later as I convert various NIC drivers to use this code.
I realize that I'm cvs adding this stuff instead of importing it
onto a separate vendor branch, but in my opinion the import approach
doesn't really offer any significant advantage: I'm going to be
maintaining this stuff and writing my own PHY drivers one way or
the other.
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.
Retire the at_shutdown family of functions and replace them with
new event handler lists.
Rework kern_shutdown.c to take greater advantage of the use of event
handlers.
Reviewed by: green
trying to size it intelligently just make it 64k and leave it up to the caller
to ensure that the arguments all fit within that range.
This should resolve the issue that some people were seeing with the PnP BIOS
scan crashing on a large PnP node.
Notice that 'unit' wasn't defined once I changed the parameters of the func.
These things make me feel like wading in with a flamethrowr or something.
Too much cruft!
</rant>
if_init_f_t is passed void * containing the address of ifp->if_softc
not the unit number.
Someone tell me if these things don't work as I don't have the hardware
needed to test them. (thats a first.)
I'll get if_ze and if_zp later.
Pointed out by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
test does not change undefined flag like Cyrix CPUs. Another is that
5/2 test changes undefined flag like Intel CPUs. Latter one could not
be detected and was recognized 486DX CPU. To solve this,
finishidentcpu() calls identblue() when cpu_vendor is null string
(that is, CPUID instruction is not supported) and cpu == CPU_486.
Tests have been done on IBM BlueLightning CPUs, i486SX and i486DX.
- increase the default timeout from 10 seconds to 60 seconds
- add a new kernel option, SCSI_PT_DEFAULT_TIMEOUT, that lets users specify
the default timeout for the pt driver to use
- add two new ioctls, one to get the timeout for a given pt device, the
other to set the timeout for a given pt device. The idea is that
userland applications using the device can set the timeout to suit their
purposes. The ioctls are defined in a new header file, sys/ptio.h
PR: 10266
Reviewed by: gibbs, joerg
into two parts - one to do the bsfl and the other to convert the result
(base 0) to ffs()-like (base 1) in inline C. This enables the optimizer
to be a lot smarter in certain cases, like where it knows that the argument
is non-zero and we want ffs(known non zero arg) - 1. This appears to
produce identical code to the old inline when the argument is unknown.
that goes to opt_dontuse.h is so an opt_*.h file doesn't get created even
though an option may be used for bringing stuff in via files[.*].
Pointed out by: bde
that are linked into the kernel. The KLD compilation options are
changed to call these functions, rather than in-lining the
atomic operations.
This approach makes atomic operations from KLDs significantly
faster on UP systems (though somewhat slower on SMP systems).
PR: i386/13111
Submitted by: peter.jeremy@alcatel.com.au
about a dev_t.
printf("%x", dev) now becomes printf("%s", devtoname(dev)) because
printing actual information about the device is much more useful then
printing a pointer to an address that would never help the developer debug.
Submitted by: phk, bde
didn't match the argument (p->p_pid).
While I'm at it, also fix the dupo in the format string and fix the annoying
inconsistency in all the debug-printfs wrt p_pid arguments. Change all of them
to use the %ld format specifier and cast the p_pid arguments to long.
Submitted by: billf
0x40 and then access data stored in real-mode segment 0x40, even when
called in protected mode. Microsoft unfortunately coddle these individuals,
and so must we if we want to run their code.
This change works around GPFs in some APM and PnP BIOS implementations.
Obtained from: Linux
The first reason for this rewrite is KNF conformance.
The second reason is to avoid redundancy. Each function printed the same
string, with only the syscall name being different. The actual printing is now
performed by a single function, which gets the syscall name as an argument.
The third reason is that of convenience. It's now very easy to add a new
dummy implementation. Just add ``DUMMY(foo);'' to the file. It's also a lot
easier now to see if a syscall has a dummy implementation or not.
The dummies are ordered on syscall number. Please maintain this when adding
new dummies (there're 32 candidates at the time of writing :-)
Reviewed by: bde
prototypes of o{s|g}etrlimit (from sys/sysproto.h). Update linux_{s|g}etrlimit
so that the arguments to o{s|g}etrlimit are corresponding the prototypes.
Pointed out by: bde
apm_bioscall() to check requested BIOS is supported or not.
- Add workaround in apm_driver_version() for the buggy BIOSes which
don't return the connection version in %ax.
PR: i386/13028
Reviewed by: sanpei@sanpei.org and Warner Losh.
functions use the new sigset_t and sigaction_t which allows support for more
than 32 signals. Only the lower 32 signals are supported for now.
linux_rt_sigaction, linux_sigaction and linux_signal use linux_do_sigaction
to do the actual work. That way unnecessary redundancy is avoided. The same
has been done for linux_rt_sigprocmask and linux_sigprocmask. They call
linux_do_sigprocmask to do the actual work.
of kernel space. Remove the ioctl supporting functions, and move the actual
code to the switch-statement. Now everybody can clearly see that the
implementation is really poor.
Also fix a typo in LINUX_TIOCGETD. The underlying function was given command
TIOCSETD instead op TIOCGETD...
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
changes. This is part 1 of the complete termios ioctl fixes.
o change type of c_{i|o|c|l}flag in struct termios from unsigned long to
unsigned int. The type now matches the Linux definitions.
o replaced constants by the corresponding defines in sptab[] for clarity.
Since there's no define for 135 baud, its mapping has been dropped.
function bsd_to_linux_termios:
o Fix typo IXON -> IXANY.
o Remove bogus assignment to c_cc[LINUX_VSWTC].
function linux_to_bsd_termios:
o Fix dupo LINUX_IXON -> LINUX_IXANY.
o Add LINUX_CREAD mapping.
o Fix typo IEXTEN -> LINUX_IEXTEN.
function linux_to_bsd_termio:
o Small optimization: Don't preset the complete c_cc array when we next
assign to the first LINUX_NCC entries.
in deterministic behaviour. In this case known garbage out.
The fix is different than suggested in the PR.
PR: 12749
Originator: Boris Nikolaus <boris@cs.tu-berlin.de>
The linux syscalls translate the arguments first before invoking the
FreeBSD native syscalls.
PR: kern/9591
Originator: John Plevyak <jplevyak@inktomi.com>
as PCI->HOST bridges on my (440BX) box.
My change is to remove the test at the beginning entirely, letting the
switch on the device ID happen first. If the device ID is unknown, then
(in the default case) check for the generic PCIS_BRIDGE_HOST tag. This
should allow wierd cases (eg: wpaul's IMS VL bridge) to work by using the
id override. This strategy is more in line with the other PCI match
methods we use elsewhere,
I only have a limited testbed, but having my USB etc devices detected as
PCI->HOST bridges doesn't look good.
correctly. It has the following code:
if (class != PCIC_BRIDGE || subclass != PCIS_BRIDGE_HOST)
return NULL;
My 486 has an Integrated Micro Solutions PCI bridge which identifies
itself as subclass PCIS_BRIDGE_OTHER, not PCIS_BRIDGE_HOST. Consequently,
it gets ignored. In my opinion, the correct test should be:
if ((class != PCIC_BRIDGE) && (subclass != PCIS_BRIDGE_HOST))
return NULL;
That way the test still succeeds because the chip's class is PCIC_BRIDGE.
Clearly it's not reasonable to expect all host to PCI bridges to always
have a subclass of PCIS_BRIDGE_HOST since I've got one that doesn't.
This way the sanity test should remain relatively sane while still allowing
some oddball yet correct hardware to work. If somebody has a better way
to do it, go ahead and tweak the test, but be aware that
class == PCIC_BRIDGE and subclass == PCIS_BRIDGE_OTHER is a valid case.
While I was here, I also added an explicit ID string for the IMS chipset.
I also dealt with a minor style nit: it's bad karma not to have a default
case for your switch statements, but the one in this routine doesn't have
one. The default string of "Host to PCI bridge" is now assigned in a
default case of the switch statement instead of initializing "s" with the
string before the switch and then not having any default case.
Config(8) contains no documentation about this.
Fix the help for the PnP irq and drq commands. This one caused
me a bit of head scratching the other night while trying to get
a problematic PnP device configured properly.
we create the pty on the fly when it is first opened.
If you run out of ptys now, just MAKEDEV some more.
This also demonstrate the use of dev_t->si_tty_tty and dev_t->si_drv1
in a device driver.
in the pathname translation procedure. This proves fatal, and can be
easily fixed. This or a similar change needs to be committed to svr4_util.h
and ibcs2_util.h. I will update ibcs2_util.h, if noone else thinks of a
better way to do this, in the same manner. I will leave svr4 to the
respective maintainer.
This closes the problem of the only crash I've been able to produce as
a user recently, except for (currently not-in-the-source tree) fd
table sharing fixes. Thanks goes to pho for his stress-testers.
of 2 weeks ago that this be done, and anyone who wishes to make bpf more
selective according to securelevel or compile-time options is more
than free to do so.
eisa_add_intr() which now takes an additional arguement (one of
EISA_TRIGGER_LEVEL or EISA_TRIGGER_EDGE).
The flag RR_SHAREABLE has no effect when passed to
bus_alloc_resource(dev, SYS_RES_IRQ, ...) in an EISA device context as
the eisa_alloc_resource() call (bus_alloc_resource method) now deals
with this flag directly, depending on the device ivars.
This change does nothing more than move all the 'shared = inb(foo + iobsse)'
nonesense to the device probe methods rather than the device attach.
Also, print out 'edge' or 'level' in the IRQ announcement message.
Reviewed by: dfr
