The extended LVT entries can be used to configure interrupt delivery
for various events that are internal to a processor and can use this
feature.
All current processors that support the feature have four of such entries.
The entries are all masked upon the processor reset, but it's possible
that firmware may use some of them.
BIOS and Kernel Developer's Guides for some processor models do not assign
any particular names to the extended LVTs, while other BKDGs provide names
and suggested usage for them.
However, there is no fixed mapping between the LVTs and the processor
events in any processor model that supports the feature. Any entry can be
assigned to any event. The assignment is done by programming an offset
of an entry into configuration bits corresponding to an event.
This change does not expose the flexibility that the feature offers.
The change adds just a single method to configure a hardcoded extended LVT
entry to deliver APIC_CMC_INT. The method is designed to be used with
Machine Check Error Thresholding mechanism on supported processor models.
For references please see BKDGs for families 10h - 16h and specifically
descriptions of APIC30, APIC400, APIC[530:500] registers.
For a description of the Error Thresholding mechanism see, for example,
BKDG for family 10h, section 2.12.1.6.
http://developer.amd.com/resources/developer-guides-manuals/
Thanks to jhb and kib for their suggestions.
Reviewed by: kib
Discussed with: jhb
MFC after: 5 weeks
Relnotes: maybe
Differential Revision: https://reviews.freebsd.org/D9612
If BIOS performed hand-off to OS with BSP LAPIC in the x2APIC mode,
system usually consumes such configuration without a notice, since
x2APIC is turned on by OS if possible (nop). But if BIOS
simultaneously requested OS to not use x2APIC, code assumption that
that xAPIC is active breaks.
In my opinion, we cannot safely turn off x2APIC if control is passed
in this mode. Make madt.c ignore user or BIOS requests to turn x2APIC
off, and do not check the x2APIC black list. Just trust the config
and try to continue, giving a warning in dmesg.
Reported and tested by: Slawa Olhovchenkov <slw@zxy.spb.ru> (previous version)
Diagnosed by and discussed with: avg
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
xen/hypervisor.h:
- Remove unused helpers: MULTI_update_va_mapping, is_initial_xendomain,
is_running_on_xen
- Remove unused define CONFIG_X86_PAE
- Remove unused variable xen_start_info: note that it's used inpcifront
which is not built at all
- Remove forward declaration of HYPERVISOR_crash
xen/xen-os.h:
- Remove unused define CONFIG_X86_PAE
- Drop unused helpers: test_and_clear_bit, clear_bit,
force_evtchn_callback
- Implement a generic version (based on ofed/include/linux/bitops.h) of
set_bit and test_bit and prefix them by xen_ to avoid any use by other
code than Xen. Note that It would be worth to investigate a generic
implementation in FreeBSD.
- Replace barrier() by __compiler_membar()
- Replace cpu_relax() by cpu_spinwait(): it's exactly the same as rep;nop
= pause
xen/xen_intr.h:
- Move the prototype of xen_intr_handle_upcall in it: Use by all the
platform
x86/xen/xen_intr.c:
- Use BITSET* for the enabledbits: Avoid to use custom helpers
- test_bit/set_bit has been renamed to xen_test_bit/xen_set_bit
- Don't export the variable xen_intr_pcpu
dev/xen/blkback/blkback.c:
- Fix the string format when XBB_DEBUG is enabled: host_addr is typed
uint64_t
dev/xen/balloon/balloon.c:
- Remove set but not used variable
- Use the correct type for frame_list: xen_pfn_t represents the frame
number on any architecture
dev/xen/control/control.c:
- Return BUS_PROBE_WILDCARD in xs_probe: Returning 0 in a probe callback
means the driver can handle this device. If by any chance xenstore is the
first driver, every new device with the driver is unset will use
xenstore.
dev/xen/grant-table/grant_table.c:
- Remove unused cmpxchg
- Drop unused include opt_pmap.h: Doesn't exist on ARM64 and it doesn't
contain anything required for the code on x86
dev/xen/netfront/netfront.c:
- Use the correct type for rx_pfn_array: xen_pfn_t represents the frame
number on any architecture
dev/xen/netback/netback.c:
- Use the correct type for gmfn: xen_pfn_t represents the frame number on
any architecture
dev/xen/xenstore/xenstore.c:
- Return BUS_PROBE_WILDCARD in xctrl_probe: Returning 0 in a probe callback
means the driver can handle this device. If by any chance xenstore is the
first driver, every new device with the driver is unset will use xenstore.
Note that with the changes, x86/include/xen/xen-os.h doesn't contain anymore
arch-specific code. Although, a new series will add some helpers that differ
between x86 and ARM64, so I've kept the headers for now.
Submitted by: Julien Grall <julien.grall@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3921
Sponsored by: Citrix Systems R&D
running thread.
It is currently implemented only on amd64 and i386; on these
architectures, it is implemented by raising an NMI on the CPU on which
the target thread is currently running. Unlike stack_save_td(), it may
fail, for example if the thread is running in user mode.
This change also modifies the kern.proc.kstack sysctl to use this function,
so that stacks of running threads are shown in the output of "procstat -kk".
This is handy for debugging threads that are stuck in a busy loop.
Reviewed by: bdrewery, jhb, kib
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3256
- Vmbus multi channel support.
- Vector interrupt support.
- Signal optimization.
- Storvsc driver performance improvement.
- Scatter and gather support for storvsc driver.
- Minor bug fix for KVP driver.
Thanks royger, jhb and delphij from FreeBSD community for the reviews
and comments. Also thanks Hovy Xu from NetApp for the contributions to
the storvsc driver.
PR: 195238
Submitted by: whu
Reviewed by: royger, jhb, delphij
Approved by: royger
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Microsoft OSTC
translation. In particular, despite IO-APICs only take 8bit apic id,
IR translation structures accept 32bit APIC Id, which allows x2APIC
mode to function properly. Extend msi_cpu of struct msi_intrsrc and
io_cpu of ioapic_intsrc to full int from one byte.
KPI of IR is isolated into the x86/iommu/iommu_intrmap.h, to avoid
bringing all dmar headers into interrupt code. The non-PCI(e) devices
which generate message interrupts on FSB require special handling. The
HPET FSB interrupts are remapped, while DMAR interrupts are not.
For each msi and ioapic interrupt source, the iommu cookie is added,
which is in fact index of the IRE (interrupt remap entry) in the IR
table. Cookie is made at the source allocation time, and then used at
the map time to fill both IRE and device registers. The MSI
address/data registers and IO-APIC redirection registers are
programmed with the special values which are recognized by IR and used
to restore the IRE index, to find proper delivery mode and target.
Map all MSI interrupts in the block when msi_map() is called.
Since an interrupt source setup and dismantle code are done in the
non-sleepable context, flushing interrupt entries cache in the IR
hardware, which is done async and ideally waits for the interrupt,
requires busy-wait for queue to drain. The dmar_qi_wait_for_seq() is
modified to take a boolean argument requesting busy-wait for the
written sequence number instead of waiting for interrupt.
Some interrupts are configured before IR is initialized, e.g. ACPI
SCI. Add intr_reprogram() function to reprogram all already
configured interrupts, and call it immediately before an IR unit is
enabled. There is still a small window after the IO-APIC redirection
entry is reprogrammed with cookie but before the unit is enabled, but
to fix this properly, IR must be started much earlier.
Add workarounds for 5500 and X58 northbridges, some revisions of which
have severe flaws in handling IR. Use the same identification methods
as employed by Linux.
Review: https://reviews.freebsd.org/D1892
Reviewed by: neel
Discussed with: jhb
Tested by: glebius, pho (previous versions)
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
vectors to be dynamically allocated. This allows kernel modules like vmm.ko
to allocate unique IPI slots when loaded (as opposed to hard allocating one
or more vectors).
Also, reorganize the fixed IPI vectors to create a contiguous space for
dynamic IPI allocation.
Reviewed by: kib, jhb
Differential Revision: https://reviews.freebsd.org/D2042
Change the numeric value of IPI_STOP_HARD so it doesn't occupy a valid IPI
slot. This can be done because IPI_STOP_HARD is actually delivered via NMI.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D1983
level-triggered interrupt does not broadcast the EOI message to all
APICs in the system. Instead, interrupt handler must follow LAPIC EOI
with IOAPIC EOI. For modern IOAPICs, the later is done by writing to
EOIR register. Otherwise, Intel provided Linux with a trick of
temporary switching the pin config to edge and then back to level.
Detect presence of EOIR register by reading IO-APIC version. The
summary table in the comments was taken from the Linux kernel. For
Intel, newer IO-APICs are only briefly documented as part of the
ICH/PCH datasheet. According to the BKDG and chipset documentation,
AMD LAPICs do not provide EOI suppression, althought IO-APICs do
declare version 0x21 and implement EOIR.
The trick to temporary switch pin to edge mode to clear IRR was tested
on modern chipset, by pretending that EOIR is not present, i.e. by
forcing io_haseoi to zero.
Tunable hw.lapic_eoi_suppression disables the optimization.
Reviewed by: neel
Tested by: pho
Review: https://reviews.freebsd.org/D1943
Sponsored by: The FreeBSD Foundation
MFC after: 2 months
hw.x2apic_enable tunable allows disabling it from the loader prompt.
To closely repeat effects of the uncached memory ops when accessing
registers in the xAPIC mode, the x2APIC writes to MSRs are preceeded
by mfence, except for the EOI notifications. This is probably too
strict, only ICR writes to send IPI require serialization to ensure
that other CPUs see the previous actions when IPI is delivered. This
may be changed later.
In vmm justreturn IPI handler, call doreti_iret instead of doing iretd
inline, to handle corner conditions.
Note that the patch only switches LAPICs into x2APIC mode. It does not
enables FreeBSD to support > 255 CPUs, which requires parsing x2APIC
MADT entries and doing interrupts remapping, but is the required step
on the way.
Reviewed by: neel
Tested by: pho (real hardware), neel (on bhyve)
Discussed with: jhb, grehan
Sponsored by: The FreeBSD Foundation
MFC after: 2 months
This is needed for Xen PV(H) guests, since there's no hardware lapic
available on this kind of domains. This commit should not change
functionality.
Sponsored by: Citrix Systems R&D
Reviewed by: jhb
Approved by: gibbs
amd64/include/cpu.h:
amd64/amd64/mp_machdep.c:
i386/include/cpu.h:
i386/i386/mp_machdep.c:
- Remove lapic_ipi_vectored hook from cpu_ops, since it's now
implemented in the lapic hooks.
amd64/amd64/mp_machdep.c:
i386/i386/mp_machdep.c:
- Use lapic_ipi_vectored directly, since it's now an inline function
that will call the appropiate hook.
x86/x86/local_apic.c:
- Prefix bare metal public lapic functions with native_ and mark them
as static.
- Define default implementation of apic_ops.
x86/include/apicvar.h:
- Declare the apic_ops structure and create inline functions to
access the hooks, so the change is transparent to existing users of
the lapic_ functions.
x86/xen/hvm.c:
- Switch to use the new apic_ops.
