Commit Graph

140 Commits

Author SHA1 Message Date
Scott Long
64c71632bf Move the CAM passthrough code into a true module so that it doesn't have to be
compiled into the main AMR driver.  It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
2008-11-03 00:53:54 +00:00
Ed Schouten
6bfa9a2d66 Replace all calls to minor() with dev2unit().
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.

This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.

Reviewed by:	kib
2008-09-27 08:51:18 +00:00
Scott Long
92130a8f2e While spin-waiting for the mailbox semaphore to update, do flushing reads of
PCI bus so that we don't have to wait more than needed.
2008-07-20 16:50:14 +00:00
Scott Long
1a6b516979 Remove an errant definition for AMR_CONFIG_ENQ3_SOLICITED NOTIFY that was
accidently reverted in the previous commit.
2008-02-06 14:26:31 +00:00
Scott Long
74018414bf Many improvements that have been collected over time:
- Improve error handling for load operations.
- Fix a memory corruption bug when using certain linux management apps.
- Allocate all commands up front to avoid OOM deadlocks later on.
2008-01-24 07:26:53 +00:00
Scott Long
281017a577 Rewrite the DMA code paths from being an impenitrable maze of special cases
to a much saner and simplier unified code path.  Along the way, fix various
CAM nits and bugs so that the passthrough works correctly for all cases.
2007-12-12 05:55:03 +00:00
Scott Long
cdc03cc897 Provide unqiue malloc types instead of using M_DEVBUF. 2007-12-02 19:54:45 +00:00
Scott Long
f4b5c2581d Refactor completion handlers so that they can be combined into a single
function.  Add missing locking.
2007-12-02 19:50:01 +00:00
Scott Long
4059f1cc7d Make a pass at style.9 compliance 2007-12-02 18:48:17 +00:00
Scott Long
4c92c3889c Fix a typo that was hidden by AMR_DEBUG. 2007-12-02 18:47:31 +00:00
Scott Long
3002614d91 Fix printf format bugs that where hidden by AMR_DEBUG. 2007-12-02 18:45:37 +00:00
Scott Long
0a5c91d058 Turn the CAM passthroug interface to AMR back ON. Adjust the
T_DIRECT filtering so that disk drives can be attached via the
pass driver.  Add CAM locking.  Don't mark CAM commands as SG64
since the hardware isn't designed to deal with 64-bit passthru
commands.  Hopefully the bounce buffer changes that were done
for the management/ioctl interface are robust enough to handle
this deficiency for CAM as well.
2007-11-28 19:40:17 +00:00
Scott Long
b50569b71d Prepare for future integration between CAM and newbus. xpt_bus_register
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now.  This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
2007-06-17 05:55:54 +00:00
Scott Long
2b83592fdc Remove Giant from CAM. Drivers (SIMs) now register a mutex that CAM will
use to synchornize and protect all data objects that are used for that
SIM.  Drivers that are not yet MPSAFE register Giant and operate as
usual.  RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.

The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
2007-04-15 08:49:19 +00:00
Paolo Pisati
ef544f6312 o break newbus api: add a new argument of type driver_filter_t to
bus_setup_intr()

o add an int return code to all fast handlers

o retire INTR_FAST/IH_FAST

For more info: http://docs.freebsd.org/cgi/getmsg.cgi?fetch=465712+0+current/freebsd-current

Reviewed by: many
Approved by: re@
2007-02-23 12:19:07 +00:00
Matt Jacob
b3d93fd0c9 Add MODULE_DEPENDS for cam, pci, mca, eisa and isa where needed.
PR:		106543
MFC after:	3 days
2006-12-11 18:28:31 +00:00
Matt Jacob
bd3fd815a7 2nd and final commit that moves us to CAM_NEW_TRAN_CODE
as the default.

Reviewed by multitudes.
2006-11-02 00:54:38 +00:00
Pawel Jakub Dawidek
9cd394ea96 Implement BIO_FLUSH handling for da(4), amr(4), ata(4) and ataraid(4).
Sponsored by:	home.pl
2006-10-31 21:19:25 +00:00
Matt Jacob
fa9ed86506 The first of 3 major steps to move the CAM layer forward to using
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.

This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).

After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.

This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.

Reviewed by:	freebsd-scsi and specific stakeholders
2006-10-31 05:53:29 +00:00
John Baldwin
44daafbccc Chain the bus_dmamap_load() calls when mapping a command with a data CCB
instead of doing the first load with the BUS_DMA_NOWAIT flag.  On 4.x with
PAE and > 4gb of RAM this proved disastrous if there weren't enough bounce
pages as amr_mapcmd() would return failure but the callback would later
fire once enough bounce pages were available and would then overwrite
another command's S/G list.

MFC after:	3 days
Submitted by:	scottl (4.x version)
Reviewed by:	scottl (port from 4.x to HEAD)
2006-07-17 19:45:47 +00:00
Doug Ambrisko
d279e43442 Make amr_linux work as a module by avoiding calling amr_linux_ioctl_int
from the amr_linux.  This simplifies the amr_linux shim and puts the
smarts into amr.c.

I tested this with 2 amr controllers in one box.  It seems to work
okay with them.
2006-05-03 16:45:15 +00:00
Doug Ambrisko
bc971e44ed Reduce the Linux ioctl range to what is needed. I didn't know what
I was doing when I first set the range up.
2006-04-14 16:13:28 +00:00
Scott Long
dce223cfb6 After further review and discussion, partially revert the previous commit.
The real problem was that ioctl handlers needed to call amr_wait_command()
with the list lock held.  This not only solves the completion race, it also
prevents bounce buffer corruption that could arise from amr_start() being
called without the proper locks held.

Discussed with: ps
MFC After: 3 days
2006-04-08 05:08:17 +00:00
Paul Saab
026d2aa333 Close a pesky race where after checking the BUSY flag in amr_wait_command,
the completion of the command can occur before tsleep is called and
the command ends up blocking forever since the wakeup has already
been called.

Submitted by:   ups
2006-04-08 02:23:27 +00:00
John Baldwin
44a4a80962 Check the return value of copyin() and return an error if it fails.
Coverity ID:	839
Found by:	Coverity Prevent
MFC after:	1 week
Reviewed by:	ps, scottl
2006-02-23 18:05:38 +00:00
Warner Losh
2805b31bdf Use void * for pointer rather than u_int8_t *, since it doesn't
matter.  Well it does for type punning warnings.
2006-02-04 22:14:20 +00:00
Paul Saab
0e74562fbc Enable 64bit SGL's on PERC 4/DC 2006-02-02 17:51:47 +00:00
Paul Saab
447c943f68 - Move the command setup from amr_start1 into the card specific submit
routines.
- Add or replace cpu_spinwait() with DELAY(1) to a few of the busy
  loops when reading from the controller to work around firmware bugs
  which can crash the controller.
2006-02-02 17:50:59 +00:00
Doug Ambrisko
4302d37921 When the RAID firmware returns a failure, don't hard error the result.
This is important with MegaLib, when issuing a GET_REBUILD_PROG since
it returns an error if the drive is not in rebuild state.

This will be MFC'ed shortly.

Submitted by:	ps
Reviewed by:	scottl
Found by:	ambrisko
2006-01-26 22:39:12 +00:00
Doug Ambrisko
084500bc13 Add in the Linux IOCTL shim and create the megadev0 device so
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.

Add in the Linux IOCTL shim and create the megadev0 device so
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.

Add glue to build the modules but don't tie it into the build
yet until I test it from the CVS repo. via the mirror on an
amd64 machine.

Tie this into the Linux32 emulation on amd64 so the tools can
run on amd64 kernel.

Cleaned up by:	ps (amr_linux.c)
2006-01-24 21:13:50 +00:00
Scott Long
a4d3c74487 Check the return value of copyin.
Found by: Coverity Prevent (tm)
2006-01-14 17:59:28 +00:00
Jung-uk Kim
9857ff20da - Correct amr_enquiry3 structure[1].
- Remove redundant AMR_CONFIG_ENQ3_SOLICITED_NOTIFY from the previous
commit while I am here.

PR:		kern/29727 [1]
2006-01-13 23:50:21 +00:00
Scott Long
174cda8010 Don't free the ap object if it was never created.
Submitted by: jkim
2006-01-10 01:55:17 +00:00
Scott Long
5351742ea2 Mega update to the LSI MegaRAID driver:
1.  Implement a large set of ioctl shims so that the Linux management apps
from LSI will work.  This includes infrastructure to support adding, deleting
and rescanning arrays at runtime.  This is based on work from Doug Ambrosko,
heavily augmented by LSI and Yahoo.

2.  Implement full 64-bit DMA support.  Systems with more than 4GB of RAM
can now operate without the cost of bounce buffers.  Cards that cannot do
64-bit DMA will automatically revert to using bounce buffers.  This option
can be forced off by setting the 'hw.amr.force_sg32" tunable in the loader.
It should only be turned off for debugging purposes.  This work was sponsored
by Yahoo.

3.  Streamline the command delivery and interrupt handler paths after
much discussion with Dell and LSI.  The logic now closely matches the
intended design, making it both more robust and much faster.  Certain
i/o failures under heavy load should be fixed with this.

4.  Optimize the locking.  In the interrupt handler, the card can be checked
for completed commands without any locks held, due to the handler being
implicitely serialized and there being no need to look at any shared data.
Only grab the lock to return the command structure to the free pool.  A
small optimization can still be made to collect all of the completions
together and then free them together under a single lock.

Items 3 and 4 significantly increase the performance of the driver.  On an
LSI 320-2X card, transactions per second went from 13,000 to 31,000 in my
testing with these changes.  However, these changes are still fairly
experimental and shouldn't be merged to 6.x until there is more testing.

Thanks to Doug Ambrosko, LSI, Dell, and Yahoo for contributing towards
this.
2005-12-14 03:26:49 +00:00
Scott Long
da7851e1e6 The CAM interface is broken and seems to be causing lockups on boot. It
doesn't appear to have worked in a long time, so just disable it completely
for now.

MFC After: 3 days
2005-11-26 07:30:09 +00:00
Scott Long
fceb189d65 Remove spl markers from AMR.
MFC After:	3 days
2005-11-06 15:13:42 +00:00
Scott Long
9cf8dd43cf Complete the removal of __FreeBSD_version checks from the amr driver. The
driver had advanced enough over the years that direct sharing of code with
FreeBSD 4.x was in no way possible anymore.
2005-08-08 12:16:21 +00:00
Scott Long
b60359e981 Remove a stale __FreeBSD_version check. 2005-08-07 23:53:00 +00:00
Scott Long
4b910da2ea The presence of a on __FreeBSD_version flagged some code that hasn't been in
the right spot since the FreeBSD 3.x days, if not earlier.
2005-08-07 23:51:53 +00:00
Paul Saab
6c9f6695fd Print the actual disk device we failed to complete i/o on. 2005-07-29 01:53:45 +00:00
Paul Saab
8c61487b21 Don't allow ioctl commands to be interrupted by the user. 2005-07-29 01:47:36 +00:00
Paul Saab
ee515ed0d9 polled commands can read or write, so bus_dmamap_sync properly
according to the type of request.

Approved by:	re
2005-06-23 00:21:25 +00:00
Yoshihiro Takahashi
d4fcf3cba5 Remove bus_{mem,p}io.h and related code for a micro-optimization on i386
and amd64.  The optimization is a trivial on recent machines.

Reviewed by:	-arch (imp, marcel, dfr)
2005-05-29 04:42:30 +00:00
Sam Leffler
fd1700dc03 handle potential null ptr
Noticed by:	Coverity Prevent analysis tool
2005-03-31 04:58:10 +00:00
Scott Long
e8447f7027 Fix a null pointer de-ref when passthrough ioctls are issued. This
involves some code shuffle to avoid locking problems.

MFC After: 3 days
2005-03-13 06:25:53 +00:00
Warner Losh
494f3ca182 Use BUS_PROBE_DEFAULT for pci probe return value 2005-03-05 19:24:22 +00:00
Scott Long
55a0283961 Fix the ioctl path by ensuring that amr_start1() gets called for commands
with no associated data.  Also revert previous changes that allocate off
of the stack instead of using malloc, as it's not needed.  Many thanks to
LSI for investigating and fixing these problems.

Submitted by: rajeshpr @ lsil . com
2005-03-04 06:11:00 +00:00
Scott Long
7e22e3674b Remove some unused variables. 2005-02-09 17:19:12 +00:00
Scott Long
29c711f038 Remove the messy locking dance around xpt_done() 2005-02-09 11:50:16 +00:00
Scott Long
35e050281e Add support for the LSI 320-2E PCI-Express controller. Fix a couple of bugs
in the ioctl handler.  Update the LSI copyrights for these.

Obtained from: LSI, Corp
2005-01-23 23:25:41 +00:00