man4.i386. It documents that meteor no longer works, but keeps the
extensive documentation on the meteor interface, which the bktr driver
implements also. This should be merged into tha man page, but such a
merging seems to be planned by others.
# we really need something like video4bsd to define these sorts of
# things for all video capture drivers.
Requested by: rwatson and obrien
note that says that this man page is sub-optimal. Bruce Mah should be
happier about this, but someone that groks the cards supported by the
digi driver is encouraged to make this man page suck less.
interfaced via the PCM framework.
This manual page was obtained from NetBSD, and the required
changes were made to adapt it to our uaudio driver.
Pre-cursor review: joe@
* Add MLINKS for:
-> Soundblaster emu10k1(4) Driver [points to pcm(4)]
-> Avance Logic ALS400 Driver [points to pcm(4)]
We should not need separate manual page for each of these
drivers; instead, linking them to pcm(4) manual page is
simpler, and new device lists can be easily added to the
said manual page.
* While I am here, sort out mdoc(7) entries in ${MAN}.
dcons(4): very simple console and gdb port driver
dcons_crom(4): FireWire attachment
dconschat(8): User interface to dcons
Tested with: i386, i386-PAE, and sparc64.
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
it attaches to all existing NATM network interfaces in the system
and creates a HARP physical interface for each of them. This allows
us to use the same set of ATM drivers for all ATM stuff. It is
possible to use the same interface for HARP, NATM and netgraph at the
same time.
This commit has two pieces. One half is the watchdog kernel code which lives
primarily in hardclock() in sys/kern/kern_clock.c. The other half is a userland
daemon which, when run, will keep the watchdog from firing while the userland
is intact and functioning.
Approved by: jeff (mentor)
man page. This will be more scaleable as more driver man pages hit
the tree. Add also a description on how to do this configuration
in the rc.conf script.
It currently supports the PMC Sierra Lite, Ultra and 622 chips and
the IDT 77105. The driver handles media options and state in a consistent
manner for ATM drivers. The next commit to the midway driver will make
it use utopia.
from NetBSD, and changed slightly to account for FreeBSD specifics.
- Hook them up to the build.
- Add them to the list of miibus-using drivers in miibus(4).
Repo-copy it from the i386 specific man4 section to the common one.
Remove the i386 keyword from the man page header.
Document the sysctl interface to the driver.
Fix a spelling error (ALL -> AAL).
