else has been probed. This feature could go away again, if we can curb the
problem another way.
if_ed.c, syscons.c: Set the above flag. ed# because it needs it, syscons
because it looks stupid to "detect" the display you have already filled up
with text :-)
bt742a.c: Check bt_cmd() return-val during probe, thus failing on adaptec's.
Also silenced various printf's during the probe.
isa.c: Probe devices with the above flag set before the rest. Reduce the
number of "conflict" messages per device to one.
***
Please test the GENERIC-kernel now, if nobody can make it fail, GENERICAH
and GENERICBT has a finite and short life-expectancy...
***
I have put it here, because I belive we could share some code among the
various kinds of boot-code, whenever we get the time to look at it.
Submitted by: Martin Renters
scheme of things, so I've changed them to be more appropriate. page in/ous
are now associated with the pager that did them. Nuked v_fault as the
only fault of interest that wouldn't be already counted in v_trap is a VM
fault, and this is counted seperately.
2) Implemented most of the remaining counters and corrected the counting of
some that were done wrong. They are all almost correct now...just a few
minor ones left to fix.
of mb_offset given the right sequence of 1 and 0 byte mbufs. This bug
was discovered by John Hood who also provided this fix - which is a
rewrite of the routine (and is easier to understand than the code I wrote).
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
This is the main files for the iBCS2 emulator. It can be use
compiled into the kernel by using:
options IBCS2
options COMPAT_IBCS2
or as a lkm module using:
options COMPAT_IBCS2
and then loading it via the ibcs2 script in /usr/bin
REMEMBER: this code is still experimental ! NO WARRENTY !
Submitted by: sef@kithrup.com, mostyn@mrl.com, sos@kmd-ac.dk
Fix endless loop in siopoll() for an event on a tty with no tty struct.
Don't generate unwanted interrupts in the serial console driver. These
bugs probably don't matter unless the tty struct is dynamically allocated.
Support polled mode. To use it, leave out the irq and the vector in
the config file. It only causes extra overhead for open polled ports.
The maximum usable speed is approximately 1000 bps for a 16450 and
15000 bps for a 16550.
Other cosmetic changes.
Bug fixed, that caused system hang on first interrupt on some motherboards.
New version of PCI bus configuration code, now supports dynamic interrupt
configuration (using BIOS supplied values).
NCR SCSI and DEC Ethernet driver patched to use this feature.
*** Remove PCI IRQ specifications from your kernel config file ! ***
"APM" macro.
machdep.c: Made the APM-descriptors unconditional.
Bruce: if these still conflict with your debugger, please put in a reservation
for your debugger. These three desc. can be anywhere, as long as they are
contiguous, so just move them as needed.
pmap.c: tons of unused vars zapped, various other warnings silenced.
trap.c: unused vars zapped.
vm_machdep.c: A wrong argument, which by chance did the right thing, was
corrected.
the first place was so that BPF could grok trailer packets. I've since
decided that this is a job for tcpdump to decipher (if at all). Also
fixed up checks for received packet length to better cope with ancient
starlan boards.
Submitted by: Thomas David Rivers <rivers%ponds@ncren.net>
WARNING: might hide some bug below! I commit this to improve the stability
of 2.0.
Thomas wrote:
-------------
I have been running a kernel with this change since October 4th; barring
unrelated network router troubles, the pitiful little machine has
completed several builds without any interaction from me, and continues
to chug along.
I re-read wd.c, and added appropriate printfs() to look for references
to dk_badsect[]. My changes should have printed something when dk_badsect[]
was referenced.
I got no output :-(
Thus, I'm forced to concluded that something else is examining some
spurious memory... which happened to be in dk_badsect[] of the disk structure
in wd.c. I can find no other explanation of why this unnecessary
initialization causes things to operate correctly.
On the premise that such an initialization isn't going to hurt anything,
I'm going to suggest it go into 2.0.
I'd like to thank everyone for there assistance, particularly David,
John and Bruce.
been relocated to run in the 64k segment at 0x10000 with the stack at
the top of this segment. This corrects the problems machines with 512K
base memory had booting.
2. startprog routing rewritten to convert the BOOTSEG ss to a KERNELSEG
ss, this eliminated the last of the >512K memory references. Additional
cleanup in here included a better way to copy the arguments to the
kernel stack.
3. Elimination of argv and esym cruft saved a few bytes.
4. Only need to truncate the head.a_entry to a meg boundary once intead
of every time we used it! [Saving more bytes].
5. Addition of version 1 bootinfo structure support. These boot blocks
pass the kernel name in to the kernel now.
6. Removed historical comments about MACH argv stuff, as it is useless now.
that and when it does it will be done differently.
2. The kernel now does a frame setup on entry so it ``looks'' like a
real function call. This will be needed by future boot code and
debuggers.
3. Clean up stack offsets to all be in decimal and use %ebp when copying
parameters in from the boot code.
4. Implement version 1 of the uniform boot code passing mechanism with
support for kernelname passing and nfs_diskless structure passing.
5. Document the 3 different ways the kernel is called depending on what code
is calling it.
be merged at some point)
New AMD family ethernet driver. Should support BICC,NE2100, TNIC,
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
must #define NFS before including <sys/mount.h> to pick up some of
the definitions needed for struct diskless. Be sure to undef it after this
so you do not effect other code.
This is kinda sick, but it does the job. Problem found by davidg.
2. Clean up the .S files to use /* */ style comments.
This is a totally cosmetic change, not one byte of the resulting boot
code changes. But at least it is installed with correct owners and in
the right places, and gets recompiled correctly when things change!
2. New detection code so we know what boot code called us.
3. Remove old DISKLESS support code and halt if we are called by that boot
code as it will NOT work with the new nfs_diskless structure.
This is really in preperation for new boot code and new diskless support.
Reviewed by: davidg
I think I have narrowed this down to the stack being overflown. I have
taken the push/pop of %fs out, it shouldn't be needed anyway, but the
real & correct solution might to save the registers on the stack in
locore.s before calling this stuff.
NOTE: 2.9 is backwards compatable with programs compiled with older
soundcard.h, but new programs compiled with 2.9 will not work on pre-2.9
sound drivers.
New version with improved support for WIDE SCSI using the NCR 53c825.
Test for buggy secondary cache implementations.
PCI Int to IRQ mapping now specified per slot.
improvements from 1.1.5.1. I tried to compile a kernel without BOUNCE_BUFFERS
with the previous version for my Bt946c and it puked and died. Bringing
these enhancements back in allows the faster controllers to DTRT while
still not messing up the older ISA/broken VLB controllers, since
bounce-buffering is still the default. In theory, anyway. Bt445S and Bt545S
folks should start testing this ASAP! (actually, Bt445C and Bt545C folks
even more so!).
including files. vector.s sometimes left the data section misaligned
(depending on the configuration) so all the time-critical globals in icu.s
were sometimes misaligned.
cycles. While waiting there I added a lot of the extra ()'s I have, (I have
never used LISP to any extent). So I compiled the kernel with -Wall and
shut up a lot of "suggest you add ()'s", removed a bunch of unused var's
and added a couple of declarations here and there. Having a lap-top is
highly recommended. My kernel still runs, yell at me if you kernel breaks.
This is needed for having the fdformat program no longer searching
non-public include paths.
Protect the definitions in fdreg.h against double inclusion.
more work required to grab all fonts
2)Make standard VGA font as default, make HARDFONTS an option
(load iso8859 fonts instead)
3)Check fonts_loaded for all restore (copy_font...palette)
sequences.
- Make a number of filesystems work again when they are statically compiled
(blush)
- FIFOs are no longer optional; ``options FIFO'' removed from distributed
config files.
matter, but similar bogusness in npx.c causes compiling without -O to fail.
Use __volatile in all asms.
Parenthesize macro args.
Change the names of the macros to avoid namespace pollution.
Remove unnecessary "#ifdef __i386__".
Sort #defines.
Add comments.
have got the following:
Back out the changes in the previous revision. Function-like macros
were replaced by compound statements that work in less contexts.
Unoformize idempotency #ifdef.
Restore the simple leap year calculation as a macro and document it so
that it doesn't become complicated again. The simple version works
for all leap years covered by 32-bit time_t's. The complicated version
doesn't work for all leap years covered by 64-bit time_t's since among
other reasons, the solar system is not stable for long enough.
Fix declarations.
Nuke spinwait().
This code is mostly taken from the 1.1 port (which was in turn taken from
Dave Mills's kern.tar.Z example). A few significant differences:
1) ntp_gettime() is now a MIB variable rather than a system call. A few
fiddles are done in libc to make it behave the same.
2) mono_time does not participate in the PLL adjustments.
3) A new interface has been defined (in <machine/clock.h>) for doing
possibly machine-dependent things around the time of the clock update.
This is used in Pentium kernels to disable interrupts, set `time', and
reset the CPU cycle counter as quickly as possible to avoid jitter in
microtime(). Measurements show an apparent resolution of a bit more than
8.14usec, which is reasonable given system-call overhead.
is used instead of /usr/lib
io.c: add #include <machine/cpufunc.h> as instructed by David Greenman to
avoid inb/outb linking errors.
NOTE: I just discovered that if GNUC is not used the inline functions will not be expanded from the include file and real inb/outb functions would
be needed.
when the drive had been left on a cylinder > 67 after kernel boot. The
most common case for this is booting a kernel that is located on
the inner cylinders of a floppy.
Also removed all occurences of spinwait(), replaced by DELAY.
Nuked a return line saying nothing, this might make Bruce happy 8^)
Submitted by: partially by Bruce Evans
date: 1994/05/22 12:35:38; author: joerg; state: Exp; lines: +6 -6
First round of floppy changes. Try making `fd' more robust.
New features:
. ioctl command for setting the drive type (density etc.); restricted
to the super-user
. ioctl for getting/seting `drive options'; currently only option
is FDOPT_NORETRY: inhibit the usual retries; used when verifying
a newly formatted track
Fixes:
. function prototypes
. made all internal functions `static'
. cleaned up & corrected .h files
. restructured, to make the chaotic function sequence more rational
. compiled with -Wall, and cleared all warnings
. introduced a mirror for the (write-only) `digital output register',
to avoid the current kludge
. device probing completed by seeking/recalibrating, and looking
for track 0 being found
. holding the controller down in reset state while it is idle (and
thus saving allot of headaches)
. make requests fail that are not a multiple of the (physical)
sector size
. removed the fixed physical sector size (512 bytes), allowing for any
size the controller could handle (128/256/512/1024 bytes)
. replaced some silly messages
. fixed the TRACE* macro usage, debugging reports should be complete
now again (debugging output is HUGE! though)
. removed fd_timeout for SEEK command; seeks are always reported by
the controller to succeed, since the `success' only refers to the
controller's idea of success - there is no hardware line to tell about
the seek end (other than the `track 0' line)
. catch SENSEI's that report about a `terminated due to READY changed'
status - could happen after a controller reset
. converted ``hz / <something>'' divide operations to divisors that are
powers of two, so gcc can optimize them into shifts
. write/format operations are checked against a write-protected medium
now *prior* starting the operation
. error reports of `invalid command' and `wrong cylinder' will cause
shortcuts in the retrier() now
. fixed a bug in the retrier() causing bogus block numbers to be reported
. fdformat() does care for errors now
Known Bugs:
. no attempts have been made (yet) to improve the performance
. sometimes, bogus ``seek/recalib failed'' messages are logged; this
is still a bug in the driver, but it's not harmful since it's
usually caught by the retrier()
Reviewed by:
Submitted by:
Obtained from:
