and that can be used as an identify function for all kinds of busses on a
certain platform. Expect for sparc64 these are only stubs right now. [1]
- For sparc64, add code to its uart_cpu_identify() for registering the on-
board ISA UARTs and their resources based on information obtained from
Open Firmware.
It would be better if this would be done in the OFW ISA code. However, due
to the common FreeBSD ISA code and PNP-IDs not always being present in the
properties of the ISA nodes there seems to be no good way to implement that.
Therefore special casing UARTs as the sole really relevant ISA devices on
sparc64 seemed reasonable. [2]
Approved by: marcel
Discussed with: marcel [1], tmm [2]
Tested by: make universe
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
from the sparc64 subtree, which breaks building non-sparc64 platforms
in the event the sparc64 subtree does not exist.
The problem is specific to the module, because non-module builds are
affected by the presence or absence of "device ebus" in the kernel
configuration.
PR: kern/56869
of what uart(4) is and/or is not see the initial commit log of one
of the files in sys/dev/uart (or see share/man/man4/uart.4).
Note that currently pc98 shares the MD file with i386. This needs
to change when pc98 support is fleshed-out to properly support the
various UARTs. A good example is sparc64 in this respect.
We build uart(4) as a module on all platforms. This may break
the ppc port. That depends on whether they do actually build
modules.
To use uart(4) on alpha, one must use the NO_SIO option.
