ip_tos == IPTOS_LOWDELAY now get precidence over urgent
packets with ip_tos != IPTOS_LOWDELAY and non-urgent packets
with ip_tos == IPTOS_LOWDELAY.
Enhance the ``set urgent'' syntax to allow for urgent UDP
packets as well as urgent TCP packets.
(LCP/CCP/IPCP), one for urgent IP traffic and one for
everything else.
o Add the ``set urgent'' command for adjusting the list of
urgent port numbers. The default urgent ports are 21, 22,
23, 513, 514, 543 and 544 (Ports 80 and 81 have been
removed from the default priority list).
o Increase the buffered packet threshold from 20 to 30.
o Report the number of packets in the IP output queue and the
list of urgent ports under ``show ipcp''.
that ppp stays in the foreground.
o Add the -quiet switch to quieten ppps startup
o Add the -nat flag and discourage the use of the -alias flag. Both do
the same thing.
o Correct some nat usage strings.
o Change the internal ``alias'' command to ``nat''.
o If we're using RADIUS and the RADIUS mtu is less than our
peers mru/mrru, reduce our mtu to this value for NetBSD too.
o Make struct throughput's sample period dynamic and tweak the ppp
version number to reflect the extra stuff being passed through
the local domain socket as a result (MP mode).
o Measure the current throughput based on the number of samples actually
taken rather than on the full sample period.
o Keep the throughput statisics persistent while being passed to
another ppp invocation through the local domain socket.
o When showing throughput statistics after the timer has stopped, use
the stopped time for overall calculations, not the current time.
Also show the stopped time and how long the current throughput has
been sampled for.
o Use time() consistently in throughput.c
o Tighten up the ``show bundle'' output.
o Introduce the ``set bandwidth'' command.
o Rewrite the ``set autoload'' command. It now takes three arguments
and works based on a rolling bundle throughput average compared against
the theoretical bundle bandwidth over a given period (read: it's now
functional).
mode by padding out the ``struct device'' to the maximum
device size.
Bump the ppp version number to indicate the transfer format
change.
This should make MP over tty and udp devices functional again.
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.
A udp device uses synchronous ppp rather than async, and avoids
the double-retransmit overhead that comes with ppp over tcp (it's
usually a bad idea to transport IP over a reliable transport that
itself is using an unreliable transport). PPP over UDP provides
througput of ** 1.5Mb per second ** with all compression disabled,
maxing out a PPro/200 when running ppp twice, back-to-back.
This proves that PPPoE is plausable in userland....
This change adds a few more handler functions to struct device and
allows derivations of struct device (which may contain their own
data etc) to pass themselves through the unix domain socket for MP.
** At last **, struct physical has lost all the tty crud !
iov2physical() is now smart enough to restore the correct stack of
layers so that MP servers will work again.
The version number has bumped as our MP link transfer contents have
changed (they now may contain a `struct device').
Don't extract the protocol twice in MP mode (resulting in protocol
rejects for every MP packet). This was broken with my original
layering changes.
Add ``Physical'' and ``Sync'' log levels for logging the relevent
raw packets and add protocol-tracking LogDEBUG stuff in various
LayerPush & LayerPull functions.
Assign our physical device name for incoming tcp connections by
calling getpeername().
Assign our physical device name for incoming udp connections from
the address retrieved by the first recvfrom().
the layering.
We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static set of `dispatch' routines are
also declared for dealing with incoming packets after they've been
`pulled' up through the stacked layers.
Physical devices are now assigned handlers based on the device type
when they're opened. For the moment there are three device types;
ttys, execs and tcps.
o Increment version number to 2.2
o Make an entry in [uw]tmp for non-tty -direct invocations (after
pap/chap authentication).
o Make throughput counters quad_t's
o Account for the absolute number of mbuf malloc()s and free()s in
``show mem''.
o ``show modem'' becomes ``show physical''.
This was pretty harmless as netmasks on a POINTOPOINT
interface are pretty much ignored, but it looked funny.
Mention the configured netmask in ``show ipcp''.
Describe in more detail what a proxy arp entry is.
that are made in each of the FSMs (LCP, CCP & IPCP) and the
number of REQs/Challenges for PAP/CHAP by accepting more arguments
in the ``set {c,ip,l}cpretry'' and ``set {ch,p}apretry'' commands.
Change the non-convergence thresholds to 3 times the number of configured
REQ tries (rather than the previous fixed ``10''). We now notice
repeated NAKs and REJs rather than just REQs.
Don't suggest that CHAP 0x05 isn't supported when it's not configured.
Fix some bugs that expose themselves with smaller numbers of retries:
o Handle instantaneous disconnects (set device /dev/null) correctly
by stopping all fsm timers in fsm2initial.
o Don't forget to uu_unlock() devices that are files but are not
ttys (set device /dev/zero).
Fix a *HORRENDOUS* bug in RFC1661 (already fixed for an Open event in state
``Closed''):
According to the state transition table, a RCR+ or RCR- received in
the ``Stopped'' state are supposed to InitRestartCounter, SendConfigReq
and SendConfig{Ack,Nak}. However, in ``Stopped'', we haven't yet
done a TLS (or the last thing we did is a TLF). We must therefore
do the TLS at this point !
This was never noticed before because LCP and CCP used not use
LayerStart() for anything interesting, and IPCP tends to go into
Stopped then get a Down because of an LCP RTR rather than getting a
RCR again.
a bum name to return as 0.0.0.0... we don't want ``delete xxx''
to delete the default route when xxx doesn't resolve.
Support IP number specifications as the host when specifying
a tcp-style device (rather than *just* hostnames).
is complete before checking carrier. If it's there,
the device supports carrier. If it's not it doesn't.
Add the ``set cd'' command for deciding how soon to check
for carrier, and for deciding if carrier is REQUIRED.
The default has changed: Pre 2.0 versions of ppp waited
for 1 second. Version 2 didn't wait, but this causes
problems with some (few?) modems that don't assert carrier
immediately on reporting CONNECT. The one second delay
is back now and can be removed with ``set cd 0''.
Bump the ppp version number in case this needs to be changed
again....
each time rather than making up a new one.
Increase the authname/authkey max sizes to 100 characters.
Allow ``authkey'' specifications beginning with ``!''.
When a challenge is received, the text following the
``!'' is executed as a program (expanding stuff in the same
way that ``sh'' and ``!bg'' do). The program is passed the
peer name, peer challenge and local ``authname'' on standard
input and is expected to output the name/key combination that
should be used to build the CHAP response.
This provides support for Secure ID cards (guess what I was
given at work recently!) using CHAP.
Examples will follow.
details. Compiling with -DNORADIUS (the default for `release')
removes support.
TODO: The functionality in libradius::rad_send_request() needs
to be supplied as a set of routines so that ppp doesn't
have to wait indefinitely for the radius server(s). Instead,
we need to get a descriptor back, select() on the descriptor,
and ask libradius to service it when necessary.
For now, ppp blocks SIGALRM while in rad_send_request(), so
it misses PAP/CHAP retries & timeouts if they occur.
Only PAP is functional. When CHAP is attempted, libradius
complains that no User-Password has been specified... rfc2138
says that it *mustn't* be used for CHAP :-(
Sponsored by: Internet Business Solutions Ltd., Switzerland
are done in the same way as command execution.
For example, ``set proctitle USER INTERFACE PROCESSID'' would
be useful in a -direct profile for identifying who's connected.
for every machine on every class C or smaller subnet that we
route to.
Add ``set {send,recv}pipe'' for controlling our socket buffer
sizes.
Mention the IP number with the problem in a few error messages.
All submitted by: Craig Leres <leres@ee.lbl.gov>
Modified slightly by: me
like
tun0: flags=blah
10.0.0.1 -> 10.0.0.100
10.0.0.2 -> 10.0.0.100
10.0.0.3 -> 10.0.0.100
to DTRT, despite the SIOCAIFADDR for each new alias returning
-1 & EEXIST while adding the alias anyway. In real life, once
we have the second alias with the same destination, nothing will
route any more ! Also, because I was ignoring EEXIST, the
dynamic IP assignment code was assigning duplicate addresses
('cos it was being lied to by iface_inAdd()).
Now we have
tun0: flags=blah
10.0.0.1 -> 255.255.255.255
10.0.0.2 -> 10.0.0.100
10.0.0.3 -> 255.255.255.255
This works - stuff bound to 10.1 & 10.3 will be considered alive
by the kernel, and when they route back to the tun device, the
packets get aliased to 10.2 and go out to 10.100 (as with the
original plan).
We still see the EEXIST in SIOCAIFADDR, but ignore it when our
destination is 255.255.255.255, assuming that the alias *was*
actually added.
Additionally, ``iface add'' may now optionally be given only
the interface address. The mask & destination default to
255.255.255.255.
shortseq, authname and authkey.
o Auth{name,key} may additionally be set in PHASE_ESTABLISH.
o The others may be set in PHASE_ESTABLISH as long as no links
have yet reached DATALINK_LCP.
demand-dial links with dynamic IP numbers where the program
that causes the dial bind()s to an interface address that is
subsequently changed after ppp negotiation.
The problem is defeated by adding negotiated addresses to the
tun interface as additional alias addresses and providing a set
of ``iface'' commands for managing the interface. Libalias is
also required (and what a name clash!) - it happily IP-aliases
the address so that the source is that of the primary (negotiated)
interface and un-IP-aliases it on the way back.
An ``enable iface-alias'' is done implicitly by the -alias command
line switch. If -alias isn't given, iface-aliasing is disabled by
default and can't be enabled 'till an ``alias enable yes'' is done.
``alias enable no'' silently disables iface-alias.
So, for dynamic-IP-type-connections, running ``ppp -alias -auto blah''
will work for the first connection, although existing bindings will
not survive a disconnect/connect as the TCP peer will be trying to
send to the old IP address - the packets won't route.
It's now a lot easier to add IPXCP to ppp with minor updates to
the new iface.[ch] (if anyone ever gets 'round to it).
It's also now possible to manually add interface aliases with
something like ``iface add 1.2.3.4/24 5.6.7.8''. This allows
multi-homed ppp links :-)
