most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
for the particular card in use. At the moment, I've set it to any of
the bt445S VLB cards (not the bt445C which apparently work) and the
bt5xx series (isa cards). The 742 and PCI cards should not need it. :-)
It may be useful to have something like this:
#ifndef BOUNCE_BUFFERS
if (bounce_buffers_required && more_than_16MB_ram)
panic("this card requires bounce buffers for more than 16MB ram!")
#endif
to get the definitions of TRUE and FALSE which happen to be defined in
a deeply nested include.
Added nearby #includes of <sys/conf.h> where appropriate.
is not real helpful since swapgeneric.c doesn't seem to be used, except
perhaps on a GENERIC kernel. (Sorry Paul.. :-)
I've moved it from swapgeneric.c to autoconf.c, since autoconf.c also deals
with dumpdev things. There may be a better place.....
but probably harmless. It's hard to tell because apparently no one runs
ity.
Fixed ity's d_reset entry. `nx' entries should never be used for existing
devices.
conf.c:
Moved a prototype to a better place.
Removed a stale #define.
sscselect(). Use the standard dummies nostrategy(), noread(),
nowrite() and noselect() instead.
sscread() and sscwrite() returned bogus errnos. It isn't possible
to return an error from a select routine so noselect() is just as
bogus as sscselect() (it's equivalent to nullselect()).
Fixed two cases of "=" that should have been "==" in card type comparison.
Simplified expression that checks for interface up/down.
Moved ed_ring_copy to before its first use so that it's inlined as intended.
Change mbuf allocation policy so that a received packet is stored in just
an mbuf header (no cluster) if it will fit in one.
Removed ifnet.if_init and ifnet.if_reset as they are generally unused.
Change the parameter passed to if_watchdog to be a ifnet * rather than
a unit number. All of this is an attempt to move toward not needing an
array of softc pointers (which is usually static in size) to point to
the driver softc.
if_ed.c:
Changed some of the argument passing to some functions to make a little
more sense.
if_ep.c, if_vx.c:
Killed completely bogus use of if_timer. It was being set in such a way
that the interface was being reset once per second (blech!).
Move a lot of variables home to their own code (In good time before xmas :-)
Introduce the string descrition of format.
Add a couple more functions to poke into these marvels, while I try to
decide what the correct interface should look like.
Next is adding vars on the fly, and sysctl looking at them too.
Removed a tine bit of defunct and #ifdefed notused code in swapgeneric.
Protected them with `#ifdef KERNEL' so that <sys/queue.h> is valid C++.
Added the necessary #includes of <sys/queue.h>.
These functions are bogus and should be replaced by the queue macros.
but also IT ACTUALLY WORKS!
FreeBSD with options JREMOD now runs with no entries in the devsw tables
prior to the devices puting their own entries there..
Thanks to bde and terry for thoughts and comments.
next stop 'Real' devfs support in devices.
- Don't print out meaningless iCOMP numbers, those are for droids.
- Use a shorter wait to determine clock rate to avoid deficiencies
in DELAY().
- Use a fixed-point representation with 8 bits of fraction to store
the rate and rationalize the variable name. It would be
possible to use even more fraction if it turns out to be
worthwhile (I rather doubt it).
The question of source code arrangement remains unaddressed.
conflicted with S3 graphics cards. Now users should put sio[2-3]
in the config file if the hardware exisst, even if the probe is
certain to fail due to an interrupt conflict. Otherwise, ports
sharing the interrupt may fail the probe if the system is warm
booted while sio[2-3] are active (perhaps under another OS). The
same problem for nonstandard ports is now handled better than
before.
add a few safety checks in specfs because
now it's possible to get entries in [cd]devsw[] which are ALL NULL
so it's better to discover this BEFORE jumping into the d_open() entry..
more check to come later.. this getsthe code to the stage where I
can start testing it, even if I haven't caught every little error case...
I guess I'll find them quick enough..
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
o Add signed/unsigned functionality to the matrox meteor device driver.
o Apply a few fixes to the sound driver.
o Add a ``SPIGOT_UNSECURE'' compile time definition so, if one defines
SPIGOT_UNSECURE in their conf file, then they can use the spigot w/o
root. There is a warning that this allows users access to the IO
page which is probably not secure.
Submitted by: james
totally dynamic. (the first was about 7 weeeks ago)
this is only the devices in i386/isa
I'll do more tomorrow.
they're completely masked by #ifdef JREMOD at this stage...
the eventual aim is that every driver will do a SYSINIT
at startup BEFORE the probes, which will effectively
link it into the devsw tables etc.
If I'd thought about it more I'd have put that in in this set (damn)
The ioconf lines generated by config will also end up in the
device's own scope as well, so ioconf.c will eventually be gutted
the SYSINIT call to the driver will include a phase where the
driver links it's ioconf line into a chain of such. when this phase is done
then the user can modify them with the boot: -c
config menu if he wants, just like now..
config will put the config lines out in the .h file
(e.g. in aha.h will be the addresses for the aha driver to look.)
as I said this is a very small first step..
the aim of THIS set of edits is to not have to edit conf.c at all when
adding a new device.. the tabe will be a simple skeleton..
when this is done, it will allow other changes to be made,
all teh time still having a fully working kernel tree,
but the logical outcome is the complete REMOVAL of the devsw tables.
By the end of this, linked in drivers will be exactly the same as
run-time loaded drivers, except they JUST HAPPEN to already be linked
and present at startup..
the SYSINIT calls will be the equivalent of the "init" call
made to a newly loaded driver in every respect.
For this edit,
each of the files has the following code inserted into it:
obviously, tailored to suit..
----------------------somewhere at the top:
#ifdef JREMOD
#include <sys/conf.h>
#define CDEV_MAJOR 13
#define BDEV_MAJOR 4
static void sd_devsw_install();
#endif /*JREMOD */
---------------------somewhere that's run during bootup: EVENTUALLY a SYSINIT
#ifdef JREMOD
sd_devsw_install();
#endif /*JREMOD*/
-----------------------at the bottom:
#ifdef JREMOD
struct bdevsw sd_bdevsw =
{ sdopen, sdclose, sdstrategy, sdioctl, /*4*/
sddump, sdsize, 0 };
struct cdevsw sd_cdevsw =
{ sdopen, sdclose, rawread, rawwrite, /*13*/
sdioctl, nostop, nullreset, nodevtotty,/* sd */
seltrue, nommap, sdstrategy };
static sd_devsw_installed = 0;
static void sd_devsw_install()
{
dev_t descript;
if( ! sd_devsw_installed ) {
descript = makedev(CDEV_MAJOR,0);
cdevsw_add(&descript,&sd_cdevsw,NULL);
#if defined(BDEV_MAJOR)
descript = makedev(BDEV_MAJOR,0);
bdevsw_add(&descript,&sd_bdevsw,NULL);
#endif /*BDEV_MAJOR*/
sd_devsw_installed = 1;
}
}
#endif /* JREMOD */
totally dynamic.
this is only the devices in i386/isa
I'll do more tomorrow.
they're completely masked by #ifdef JREMOD at this stage...
the eventual aim is that every driver will do a SYSINIT
at startup BEFORE the probes, which will effectively
link it into the devsw tables etc.
If I'd thought about it more I'd have put that in in this set (damn)
The ioconf lines generated by config will also end up in the
device's own scope as well, so ioconf.c will eventually be gutted
the SYSINIT call to the driver will include a phase where the
driver links it's ioconf line into a chain of such. when this phase is done
then the user can modify them with the boot: -c
config menu if he wants, just like now..
config will put the config lines out in the .h file
(e.g. in aha.h will be the addresses for the aha driver to look.)
as I said this is a very small first step..
the aim of THIS set of edits is to not have to edit conf.c at all when
adding a new device.. the tabe will be a simple skeleton..
when this is done, it will allow other changes to be made,
all teh time still having a fully working kernel tree,
but the logical outcome is the complete REMOVAL of the devsw tables.
By the end of this, linked in drivers will be exactly the same as
run-time loaded drivers, except they JUST HAPPEN to already be linked
and present at startup..
the SYSINIT calls will be the equivalent of the "init" call
made to a newly loaded driver in every respect.
For this edit,
each of the files has the following code inserted into it:
obviously, tailored to suit..
----------------------somewhere at the top:
#ifdef JREMOD
#include <sys/conf.h>
#define CDEV_MAJOR 13
#define BDEV_MAJOR 4
static void sd_devsw_install();
#endif /*JREMOD */
---------------------somewhere that's run during bootup: EVENTUALLY a SYSINIT
#ifdef JREMOD
sd_devsw_install();
#endif /*JREMOD*/
-----------------------at the bottom:
#ifdef JREMOD
struct bdevsw sd_bdevsw =
{ sdopen, sdclose, sdstrategy, sdioctl, /*4*/
sddump, sdsize, 0 };
struct cdevsw sd_cdevsw =
{ sdopen, sdclose, rawread, rawwrite, /*13*/
sdioctl, nostop, nullreset, nodevtotty,/* sd */
seltrue, nommap, sdstrategy };
static sd_devsw_installed = 0;
static void sd_devsw_install()
{
dev_t descript;
if( ! sd_devsw_installed ) {
descript = makedev(CDEV_MAJOR,0);
cdevsw_add(&descript,&sd_cdevsw,NULL);
#if defined(BDEV_MAJOR)
descript = makedev(BDEV_MAJOR,0);
bdevsw_add(&descript,&sd_bdevsw,NULL);
#endif /*BDEV_MAJOR*/
sd_devsw_installed = 1;
}
}
#endif /* JREMOD */
it `const' to inhibit compiler warnings.
Added #include of <pccard/driver.h> to get prototypes. <pccard/slot.h>
is still necessary for its side effect of exporting non-slot things.
HD64570 chip. Both the 2 and 4 port cards is supported and auto detected.
Line speeds of up to 2Mbps is possible. At this speed about 85% of the
bandwidth is usable with 486DX processors.
The standard FreeBSD sppp code is used for the link level layer. The
default protocol used is PPP. The Cisco HDLC protocol can be used by
adding "link2" to the ifconfig line in /etc/sysconfig or where ever
ifconfig is run.
At the moment only the V.35 and X.21 interfaces is supported. The others
may need tweaks to the clock selection code.
Submitted by: John Hay <jhay@mikom.csir.co.za>
bit set. I broke stat_imask in Dec 1994 and update_intr_masks() has
copied the breakage to intr_mask[8] since Mar 1995. This can cause
the RTC to stop interrupting in rare cases (under loads heavy enough
for a new RTC interrupt to occur at a critical time just before Xintr8
finishes handling the previous one) and may have caused worse problems.
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
almost every time someone uses an address. This file is probably not
the right place to keep track of the unused addresses (or used
addresses :->).
Fixed comments on #endif's to match code.
Added defines for ASC and GSC sizes. This file is not the right place
to keep track of scanner addresses, but while there here and we
pretend to keep track of unused addresses, the sizes need to be here
too.
Sorted IO_*SIZE defines.
floppies must have been random in 2.x since we reintroduced sorting
on b_pblkno on 1995/03/18. Drivers still initialize b_cylin/b_resid
although this is no longer used.
Removed unused, wrong function fdsize(). (Returning 0 means that the
device exists and has size 0, not that the device doesn't exist.
swaponvp() allows for size 0 by stupidly calling the d_psize function
twice if the size isn't 0. setdumpdev() doesn't allow for it.)
Continued removing /* ARGSUSED */ from drivers.
introduced.
Fixed the device-driverness of atapi.c and spkr.c.
These changes are actually no-ops because ${DRIVER_C} is the same as
${NORMAL_C} for the i386. I could do without magic CFLAGS. Special
handling should be in the sources if possible.
boot to display "Booting the kernelel...done" instead of "Booting
the kernel".
Removed save and restore of BIOS memory. kzipped kernels haven't
ever overlaid the BIOS memory.
#include <i386/isa/isa_device.h>
#include <i386/eisa/eisaconf.h>
#include <pci/pcireg.h>
#include <pci/pcivar.h>
#include <scsi/scsi_all.h>
#include <scsi/scsiconf.h>
they are not needed, and slows down compilation.
from a string to an identifier so that it can be used to generate
declarations and strings. It's much easier to stringize an identifier
than to identifize a string. A uniform naming scheme must be used
for the automatically generated things to apply. This is a feature.
Used the module identifer to generate prototypes for the module load,
unload and stat functions. Removed the few prototypes for these that
already existed.
Used the module identifier to generate a unique struct tag in MOD_DEV().
This should probably be done for all the MOD_*() macros.
Moved the trailing semicolon from the MOD_*() macro definitions to the
macro invocations that didn't already (bogusly) have it.
Staticized the module load and unload functions.
Added function return types for the module load, unload and stat functions.
lkm/ibcs2/ibcs2.c:
Included <sys/sysproto.h> to get everything prototyped.
Cleaned up #includes.
lkm/ibcs2/ipfw.c:
Cleaned up #includes.
lkm/linux/linux.c:
The module name had to change from "linux_emulator" to "linux_mod" to
be automatically generated.
Cleaned up #includes.
lkm/syscons/*/*_saver.c:
Completed delcarations of function pointers.
sys/i386/isa/atapi.c:
The module name had to change from "atapi" to "atapi_mod" to be
automatically generated.
sys/i386/isa/wcd.c:
Used the fixed MOD_DEV(). This module has two devices and expanded the
macro in the source instead of fixing it.
The module names had to change from "wcd" and "rwcd" to "wcd_mod" and
"rwcd_mod" to be automatically generated.
sys/pccard/pcic.c:
The module name had to change from "pcic" to "pcic_mod" to be
automatically generated.
much as I'd like to, but the malloc stunt I tried for an interim for
sure does worse.
Now we can read and write from any kind of address-space, not only
user and kernel, using callbacks.
This may be over-generalization for now, but it's actually simpler.
Included <sys/sysproto.h> to get central declarations for syscall args
structs and prototypes for syscalls.
Ifdefed duplicated decentralized declarations of args structs. It's
convenient to have this visible but they are hard to maintain. Some
are already different from the central declarations. 4.4lite2 puts
them in comments in the function headers but I wanted to avoid the
large changes for that.
- collapsed #if-#elses that became null.
- removed dead comments.
Moved #defines that always have the same value to the tables.
Collapsed more #if-#elses that became null. None are left.
Removed repetitive comments.
Most of this is cleaning up, but there are some functional changes,
doc/comment improvements, error checking, gcc -Wall cleanups. Input buffer
flushing is enabled now, although I'm still not quite certain it's right.
Handle kdc registration correctly. Catch ISA devices that use eisa
registration and output probe information accordingly.
lsdev will have to be updated to handle EISA devices correctly.
aic7770.c:
Set kdc_isa0 as the parent for 284X cards since its a VL card.
Changed vnodep -> vp for consistency with the rest of the kernel, and
changed iparams -> imgp for brevity.
kern_exec.c:
Explicitly initialized some additional parts of the image_params struct
to avoid bzeroing it. Rewrote the set-id code to reduce the number of
logical tests. The rewrite exposed a mostly benign bug in the algorithm:
traced set-id images would get ktracing disabled even if the set-id didn't
happen for other reasons.
cards like the Adaptec 284x that use EISA ID registers for identification
even when in stalled in non-EISA systems.
Use one format throught the files.
-Wall fixes.
These functions went away:
enosys (hasn't been used for some time)
enxio
enodev
enoioctl (was used only once, actually for a vop)
if_tun.c:
Continued cleaning up...
conf.h:
Probably fixed the type of d_reset_t. It is hard to tell the correct
type because there are no non-dummy device reset functions.
Removed last vestige of ambiguous sleep message strings.
Start the revamp of the initialiation process. New routines include
ahc_alloc, ahc_free, and ahc_reset. These help divide the work of staring
up a board more logically between probe and attach.
ahcintr now takes a (void *) and returns int. The pci code uses it directly.
Until the PCI code for shared edged triggered interrupts is removed, the
eisa code uses a stub (ahc_eisa_intr) that throws away the int returned
by ahcintr.
Use MHz instead of MB/s for printing out sync rates.
Print out "aic7880" instead of "aic7870" for the new aic7880 chips.
in here to do some conflict detection. The new code doesn't do conflict
detection yet, but it will be implemented in another way.
aic7770.c moved to i386/eisa
be the beginning of our move to a more dynamic (configuration manager)
based setup for all drivers. Everything seems to work except for
some devconf problems. Only the aic7xxx driver will be using this
interface until it is reviewed, revised and accepted as a good configuration
interface.
Adapt aic7770.c to use new eisaconf.
eisadevs.c is replaced by a linker set.
misplaced extern declarations (mostly prototypes of interrupt handlers)
that this exposed. The prototypes should be moved back to the driver
sources when the functions are staticalized.
Added idempotency guards to <machine/conf.h>. "ioconf.h" can't be
included when building LKMs so define a wart in bsd.kmod.mk to help
guard against including it.
/dev/random is now a part of the kernel! you will need to make
the device in /dev: sh MAKEDEV random
and take a look at some test code in src/tools/test/random.
incompatible with the type of a PCI interrupt handler. A new entry
point `ahc_pci_intr()' is used for PCI. ISA and PCI interrupts are
penalized equally (:-) by calling a common handler `ahc_intr()'. This
should be reorganized. Some strings now name the wrong function...
to <machine/conf.h>. conf.h was mechanically generated by
`grep ^d_ conf.c >conf.h'. This accounts for part of its ugliness. The
prototypes should be moved back to the driver sources when the functions
are staticalized.
the kernel. ppp_tty.c goes to some lengths to minimise the inter-layer
calling (including a soft ISR). ppp_tty.c takes care of the soft masking
that was needed still.
(I've discovered that bugs in this area show up within an hour if the
masking was not correct.. :-} This combination has proven stable on
specialix serial ports, although there was some concern about the softtty
parts of sio/cy and netisr colliding - but Bruce has fixed that now)
Submitted by: fgray@rice.edu
this driver hasn't been checked but as a separate module, bringing it in won't
break anything else and it't the best way of testing it......
julian
line discipline interrupt handlers more or less expect to be called at
spltty() == splimp(), although they have internal splimp()s that are
bogus if this expectation is satisfied. They are called at splsoftty()
from many tty drivers, so they were not protected from being reentered
from their own netisrs. They certainly don't expect that but are
apparently remarkably robust if it occurs. The problem in PR 798 seems
to be caused by pppstart() being reentered and finishing off the output
in progress by following the (stale) sc->sc_outm pointer. Then the
original pppstart() finds garbage in m2 after MFREE(m, m2). slstart()
doesn't have internal state like sc_outm so reentry of it probably only
causes out of order and dropped packets.
modularization of the wd/wcd/atapi driver is ugly.
Include cons.h from a less bogus place.
Removed an ARGSUSED. Unused args are normal for devswitch functions
and lint was informed about them for about 5 functions out of 1000.
Lint should be informed about them, if at all, in some other way.
Remove confusing backwards compatibility code that allowed driver to be
used in pre-4.4 releases. The 3COM card's use -link2 to switch tranceivers.
(no functional changes here)
