count of valid frequencies and use that as the final package count, don't
give up when the first invalid state is found. Also, add 0x9999 and expand
our upper check to >= 0xffff Mhz [2].
Submitted by: Bruno Ducrot, Jung-uk Kim [2]
found it guilty in putting the card into unusable state after UP->DOWN->UP
media status change.
Looks like some of register writes in this functions mess up PHY interface.
No visible regressions has been found after commenting this code out -
the card properly handles forceful local mode changes and auto-detects changes
made remotely (tested with Auto, 10HD, 10FD, 100HD, 100FD).
Sponsored by: PBXpress Inc.
MFC after: 3 days
of the device id.
- Use BAR2 rather than BAR0 for the Rocketport UPCI 8O card. I suspect
that other UPCI cards might need to use BAR2 as well.
Tested by: wsk at gddsn dot org dot cn
MFC after: 1 week
with the wrong language parameter when retrieving the device serial
number. This invalid request caused some devices not to work at
all.
PR: usb/79190
Submitted by: Hans Petter Selasky <hselasky@c2i.net>
FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
(like an EC/SMbus controller) to access the EC address space. Access
is synchronized by the EcLock/Unlock routines in EcSpaceHandler().
Tested by: Hans Petter Selasky
configure_final(), assert that "cold" is true in usb_cold_explore()
when there are busses to explore. When USB is kldloaded after boot,
usb_cold_explore() will still get invoked but the list of busses
to explore in that case should always be empty.
transfer, which lead to panics or page faults. For example if a
transfer timed out, another thread could come along and attempt to
abort the same transfer while the timeout task was sleeping in
the *_abort_xfer() function.
Add an "aborting" flag to the private transfer state in each host
controller driver and use this to ensure that the abort is only
executed once. Also prioritise normal abort requests over timeouts
so that the callback is always given a status of USB_CANCELLED even
if the timeout-initiated abort began first.
The crashes caused by this bug were mainly reported in connection
with lpd printing to a USB printer.
PR: usb/78208, usb/78986
last in the list rather than first.
This makes the resouces print in the 4.x order rather than the 5.x order
(eg fdc0 at 0x3f0-0x3f5,0x3f7 is 4.x, but 0x3f7,0x3f0-0x3f5 is 5.x). This
also means that the pci code will once again print the resources in BAR
ascending order.
same value as the previous ioctls so no binary change. Also, make a few
style changes to reduce diffs to my tree.
Loosely based on code from: Hans Petter Selasky
system have been attached, but no later. This ensures that we do
not explore ohci or uhci busses before the companion echi controller
has been initialised, so it should fix the problem of multi-speed
USB devices getting attached as USB 1 devices first and then
re-attached as USB 2.
Some further changes are needed on architectures that do not currently
allow hooks to be inserted before configure_final() - alpha, ia64,
powerpc and sparc64. On these architectures the exploration will
now be delayed until the usb kthread runs.
Do our best to plug some memory leaks (VPD data, jumbo memory buffer,...).
Log if we cannot free because memory still in use[1].
Change locking to avoid ''acquiring duplicate lock of same
type: "network driver"'' and potential deadlock. Also seems to fix LOR #063.
[1] This change does not solve problems if buffers are still in use when
unloading if_sk.ko. There is ongoing work which will address jumbogram
allocations in a more general way.
PR: kern/75677 (with changes, no mii fixes in here)
Tested by: net, Antoine Brodin (slightly different version)
Approved by: rwatson (mentor)
MFC after: 5 days
Obtained from: NetBSD if_sk.c rev. 1.11
* Take PHY out of reset for Yukon Lite Rev. A3.
Submitted by: postings on net@ in thread "skc0: no PHY found", 2005-02-22
Tested by: net
Approved by: rwatson (mentor)
MFC after: 5 days
if the interface is marked RUNNING.
Obtained from: NetBSD if_sk.c rev. 1.12
* Don't initialize the card (and start an autonegotiation) every time the IP
address changes. Makes 'dhclient sk0' invocations way faster and more
consistant. i.e. one DHCPREQUEST elicits the DHCPACK.
Obtained from: OpenBSD if_sk.c rev. 1.56
* Additional locking changes in sk_ioctl.
PR: kern/61296 should see improvements by the last two.
Approved by: rwatson (mentor)
MFC after: 5 days
doing that in bfe_stop().
This should fix a panic recently reported on -current occuring when taking
device down then up. In the original implementation, an "ifconfig bfe0 down"
triggers bfe_stop(), which also destroys all TX/RX descriptor dmamaps. Hence
the subsequent "ifconfig bfe0 up" would force the device to use those
already-released dmamap and thus panic the kernel.
PR: kern/77804
Submitted by: Frank Mayhar <frank at exit dot com>
Reviewed by: dmlb, sam (mentor)
Tested by: Phil <pcasidy at casidy dot com>, myself
MFC after: 1 week
that we free that resource. All the other resources are freed in
their own routine, but since we haven't saved a pointer to this one,
it is leaked. This is the failure case that lead to the sio ports
that weren't working, I think.
cleared if the host controller retries the transfer and is successful,
but we were interpreting these bits as indicating a fatal error.
Ignore these error bits, and instead use the HALTED bit to determine
if the transfer failed. Also update the USBD_STALLED detection to
ignore these bits.
Obtained from: OpenBSD
between passes over a QH. Previously the accesses to a QH were
bunched together in time, so the interval was often much longer
than intended. This now appears to match the diagrams in the EHCI
spec, so remove the XXX comment.
a serial console anyway because input-device is set to keyboard and
output-device is set to screen but no keyboard is plugged in don't
assume that a device node for the input-device alias exists. While
this is true for RS232 keyboards (the node of the SCC and UART
respectively which controls the keyboard doesn't disappear when no
keyboard is plugged in) this assumption breaks for USB keyboards.
It's most likely also not true for PS/2 keyboards but OFW doesn't
reliably switch to a serial console when the potential keyboard is
a PS/2 one which isn't plugged in so this couldn't be verified
properly.
Reported by: Will Andrews <will@csociety.org>, obrien
MFC after: 1 week
to syncrhonize access to the data as a result. This makes the pps
less likely to miss the 1ms pulse that I'm feeding it, but not
entirely reliable yet on my 133MHz P5.
Reviewed by: phk
unknown (since my sony vaio didn't :-(.
Instead, fix the problem described by 1.49 in a different way: just
add the two calls I'd hoped I'd avoid in 1.49 by doing the (wrong)
gymnastics there. While 1.49 is a good direction to go in, each step
of the way should work :-(.
resources. When allocating 6 ports for a 4 port range isa code
returns an error. I'm not sure yet why this is the case, but suspect
it is just a non-regularity in how the resource allocation code works
which should be corrected. Use 1 as the ports size in this case.
However, in the hints case, we have to specify the length, so use 6 in
that case. I believe that this is also acpi friendly.
Also, complain when we can't allocate FDOUT register space. Right now we
silently fail when we can't. This failure is referred to above.
When there's no resource for FDCTL, go ahead and allocate one by hand.
Many PNPBIOS tables don't list this resource, and our hints mechanism also
doesn't cover that range. If we can't allocate it, whine, but fake up
something. Before, we were always bogusly faking it and no one noticed
the sham (save the original author who has now fixed his private shame).
asks that each buffer be (2048 * 256) bytes long. I suspect that alignment
isn't a real requirement since busdma only recently started honoring it. The
size is also bogus. Fix both of these and stop busdma from trying to
exhaust the system memory pool with bounce pages.
Submitted by: Kevin Oberman
MFC After: 7 days
- Fix a bug in the same condition where we forgot to drop the ACPI pcib
lock. This fixes hangs after the pcib0 attach on some machines.
Tested by: sos (2)
ever working correctly: the code was linking the QHs together but
then immediately overwriting the "next" pointers. Oops. Also
initialise qh_endphub, since the EHCI spec says that we should
always set the pipe multiplier field to something sensible.
This appears to make basic split transactions work, so enable split
transactions for control, bulk and interrupt pipes (split isochronous
transfers are not yet implemented). It should now be possible to
use USB1 devices even when they are connected through a USB2 hub.