Commit Graph

8968 Commits

Author SHA1 Message Date
Hidetoshi Shimokawa
f34e847dce - The payload of Write Request Quad must be network byte order. 2003-03-24 04:11:21 +00:00
Hidetoshi Shimokawa
73aa55ba0a - The payload of Write Request Quad and Read Response Quad must be
network byte order.
- Set ATRetries register after each bus reset because the value is 'undef'
	in OHCI spec.
2003-03-24 04:06:21 +00:00
Hidetoshi Shimokawa
a84fda13bb Safe PCI configuration.
- Clear PCIM_CMD_MWRICEN:
	some chips seem to have problem with write invalidate.
	clearing this bit fixes SBP timeout problem.

Tested by: Michael Reifenberger <Michael.Reifenberger@Plaut.de>

- Set PCIM_CMD_SERRESPEN and PCIM_CMD_PERRESPEN
- Moderate value for latency timer.
2003-03-24 03:47:36 +00:00
Warner Losh
fb9e391927 MFP4 27224 and 27225:
Change 27224 by imp@imp_hammer on 2003/03/22 00:16:22
	Put what I think are the correct TX RATE translation tables
	in place for LUCENT firmware.  This is based on the 4.x driver.
	Maybe it should be table driven?

	ifconfig wi0 media DS/11Mbps still fails, but it fails before
	we even get to the txrate stuff, so other things are wrong.

Change 27225 by imp@imp_hammer on 2003/03/22 00:45:11
	Default ic_fixed_rate to -1.  This is the same thing as autoselect.
	There really should be a #define for this...
2003-03-22 15:39:38 +00:00
Maxime Henrion
0a50de79cb - Add a new ioctl to get the maximum number of ATA channels.
- Use it in atacontrol(8) when listing ATA devices instead of
  stopping at the first ENXIO received.

This makes atacontrol list work on my sparc64 where the two ATA
channels I have are numbered 2 and 3.

Reviewed by:	sos
2003-03-22 12:18:20 +00:00
Ruslan Ermilov
7f18da65a4 Added missing dependency on rc4.
Reviewed by:	imp
2003-03-21 22:02:58 +00:00
Prafulla Deuskar
55cbc7f8bd Added support for 82541 and 82547 based adapters.
- These have Intel gigabit PHY
 - 82547 uses CSA interface

MFC after:	1 week
2003-03-21 21:47:31 +00:00
Matthew N. Dodd
868d8b6286 - Use if_broadcastaddr from struct ifnet rather than relying on
extern 'etherbroadcastaddr'.
- Make 'etherbroadcastaddr' static.

Reviewed by:	 imp
2003-03-21 17:53:16 +00:00
John Baldwin
31566c96f4 Use td->td_ucred instead of td->td_proc->p_ucred. 2003-03-20 21:17:40 +00:00
Orion Hodson
600f6cbaa2 Distinguish between register sets that depend on ac97 caps (wr0, wr1,
msgd) and those that don't (dxs0-3) when reporting format caps.
2003-03-20 20:07:18 +00:00
Orion Hodson
9963235abc Correct vendor id for ALC101. 2003-03-20 18:17:39 +00:00
Hidetoshi Shimokawa
58089a20d1 Clear channel and tag bits before set them.
This should fix the problem that if_fwe doesn't work after DV receiving.
2003-03-19 07:04:11 +00:00
Maxim Sobolev
2d95f7d4a9 Brucify.
Requested and reviewed by:	bde
MFC after:	2 weeks
2003-03-18 21:26:28 +00:00
Poul-Henning Kamp
b4b138c27f Including <sys/stdint.h> is (almost?) universally only to be able to use
%j in printfs, so put a newsted include in <sys/systm.h> where the printf
prototype lives and save everybody else the trouble.
2003-03-18 08:45:25 +00:00
Warner Losh
0e630ee24b o Lucent cards don't seem to like multiple buffers for tx. Use only
one tx buffer for these cards.  The old driver only used one.  We use
  1 for symbol, and 3 for prism cards.
o Don't do the maximum loops thing in the ISR.  In fact, revert to the
  old interrupt handler.  Lucent cards don't seem to work too well if
  you don't disable/enable interrupts from the card in the ISR.

Between these two changes, Lucent cards suck less.  They work in
autoselect mode only.  And seem to get 1Mbps or 2Mbps only.  Setting a
specific media speed doesn't work, and I've had a few issues even with
these patches.  They turn a former brick into a nearly useful card.

These patches work on the prism 2 and 2.5 PC Card cards that I have.
I've not tested this on PCI cards.  I suspect, but couldn't find
proof, that they were the reason that the ISR was changed so radically
from its FreeBSD roots in NetBSD.  We might need to have a variant ISR
if so.
2003-03-18 04:22:42 +00:00
Warner Losh
572ab50c54 Move symbol reset detection code back into wi_reset. This is a more
reliable way to detect if the symbol cards have been reset or not.
This makes symbol cards work better.

Submitted by: deischen
2003-03-18 02:54:39 +00:00
Warner Losh
08d49adb7f Add DLINK DWL650H
From NetBSD by way of deischen
2003-03-18 02:47:53 +00:00
Warner Losh
7a073cc3e0 Add SMC 2602W pci card, from a post to mobile@ 2003-03-18 02:45:29 +00:00
Warner Losh
b43a533ddb Use %jd and a cast to intmax_t instead of a cast to long.
Minor style nit while I'm here.
2003-03-18 02:40:40 +00:00
Warner Losh
ec72163b64 Tag longling_addr as maybe using a bad type, I'm not sure. 2003-03-18 02:38:33 +00:00
Warner Losh
1831679c41 Regenerate for 1.45 2003-03-18 02:37:25 +00:00
Warner Losh
2a72cb5210 Add DLINK DWL650H
From NetBSD by way of deichen
2003-03-18 02:36:54 +00:00
Warner Losh
fabc845e37 Remove bogus KASSERT. The 802.11 layer and the resume from suspend
code both seem to call wi_start (directly or via the if_start pointer)
without checking to see if OACTIVE is 0.  In addition, I think that
with the use of 3 transmit buffers this routine can be called with
OACTIVE set, but I might be mistaken about that (and it doesn't
matter).

Reviewed by: sam
Noticed by: imp, alfred, ambrisko
2003-03-17 13:19:28 +00:00
Poul-Henning Kamp
8595de4aec Fix a malloc() with no legal modeflag. 2003-03-17 07:26:25 +00:00
Søren Schmidt
92737d1739 Fix the cable detection and properly find the host bridge on
older SiS chips.
2003-03-16 16:26:51 +00:00
Matthew N. Dodd
fae930213c Catch up with bpf_mtap() changes. 2003-03-16 00:30:02 +00:00
Matthew N. Dodd
2d6bcb381e Catch up with recent infrastructure changes. 2003-03-16 00:24:18 +00:00
Maxim Sobolev
71fbba351a Remove duplicate line introduced in the previous commit.
Submitted by:	bde
MFC after:	2 weeks
2003-03-15 18:49:41 +00:00
Maxim Sobolev
084254f807 - Add minimal support for TI16754 4xUART chip into sio(4) driver and remove
now unnecessary hack from the previous commit;
- Add support for Interrupt Latch Register (ILR) into puc(4). So far only
  ILRs compatible with specifications from Digi International are supported.
  Support for other types of ILRs could be easily added later;
- Correct clock frequency for IC Book Labs Dreadnought x16 Lite board;
- Enable ILR detection/usage for IC Book Labs Dreadnought x16 boards.

Sponsored by:   IC Book Labs
MFC after:      2 weeks
2003-03-15 16:25:40 +00:00
Takanori Watanabe
869c12cbb4 Add module dependency. This makes udbp.ko to be loaded. 2003-03-15 13:03:30 +00:00
Poul-Henning Kamp
fe002e7546 Fix a bug I introduced by overlooking the fact that "unit number" can
be one of several things in this driver.

Spotted & Tested by:	alfred
2003-03-15 12:16:33 +00:00
Poul-Henning Kamp
09a6b2aad6 Call devstat_start_transaction_bio() instead of devstat_start_transaction(). 2003-03-15 10:56:19 +00:00
Poul-Henning Kamp
1ecc485c1b Call devstat_start_transaction_bio() instead of devstat_start_transaction() 2003-03-15 10:50:44 +00:00
Scott Long
6f420b1756 Now that bus_dmamem_alloc() handles its Giant mutex requirements itself,
don't bother doing the same in the code that calls it.
2003-03-13 22:56:11 +00:00
Søren Schmidt
f711eff1d2 Remove the check for more than one open if one is a write op.
This allows using DVD+RW and DVD-RW as random storage, provided
the 32K blocksize is honoured for DVD-RW (DVD+RW has built in
read-modify-write).
2003-03-13 09:12:17 +00:00
Søren Schmidt
6918962fad Dont free the stats struct, this has been changed by the new stat code.
Spotted by: Ian Dowse <iedowse@maths.tcd.ie>
2003-03-13 09:09:10 +00:00
Søren Schmidt
394046e66f Dont call dma->free unless dma is there.
Spotted by: Ian Dowse <iedowse@maths.tcd.ie>
2003-03-13 09:04:55 +00:00
Søren Schmidt
64eca1e1f2 Add pci id# for the sis648 2003-03-13 07:55:53 +00:00
Maxim Sobolev
525e5ed929 Correct clock frequency for the IC Book Labs' cards, so that it's possible
to use speeds higher than 115200.

Sponsored by:	IC Book Labs
MFC after:	2 weeks
2003-03-12 17:56:03 +00:00
Maxim Sobolev
a2a101e766 Add initial support for IC Book Labs Dreadnought x16 Pro 16-ports card. Since
this card is based on 16750 UART, modify sio(4) a bit to ignore 16750-specific
7th bit of MCR when probing card. This allows card to be detected and attached
as 16550A-compatible device. More work needs to be done in order to enable
nice 16750-specific features such as larger fifo buffer and higher speeds.

Sponsored by:	IC Book Labs
MFC after:	2 weeks
2003-03-12 17:20:24 +00:00
Søren Schmidt
deff57d72c Correct the last commit, only look for subfunctions on the same PCI slot. 2003-03-12 15:45:52 +00:00
Orion Hodson
b2a0f525e6 Correct CS4205 base vendor id.
Reported by:    Christophe Juniet and Mark Santcroos.
2003-03-12 15:11:25 +00:00
Søren Schmidt
5b24125046 Cleanup the probe code a bit. 2003-03-12 12:05:17 +00:00
Søren Schmidt
9eb8572ea2 Dont hang the channel on enclosures without sensors. 2003-03-12 10:59:35 +00:00
Hidetoshi Shimokawa
d067ce208d Put back including sys/devicestat.h for 4-stable. 2003-03-12 10:36:53 +00:00
Kenjiro Cho
fec4b7015e clean up the en driver since it will survice for a while by
Harti Brandt's effort.
remove the DMA test to detect problems of the first generation PCI chipsets
back in 1998.
it is no longer needed and has been the source of the false alarm that
the driver uses too much stack space.
2003-03-12 10:28:26 +00:00
Sam Leffler
cff5befbba FIPS 140-2 rng data tester for h/w crypto devices. This driver periodically
monitors the entropy data harvested by crypto drivers to verify it complies
with FIPS 140-2.  If data fails any test then the driver discards it and
commences continuous testing of harvested data until it is deemed ok.
Results are collected in a statistics block and, optionally, reported on
the console.  In normal use the overhead associated with this driver is
not noticeable.

Note that drivers must (currently) be compiled specially to enable use.

Obtained from:	original code by Jason L. Wright
2003-03-11 22:54:44 +00:00
Sam Leffler
b7c4858f1e o add crypto driver glue for using the new rndtest driver/module; this is
conditional in each driver on foo_RNDTEST being defined_
o bring HIFN_DEBUG and UBSEC_DEBUG out to be visible options; they control
  the debugging printfs that are set with hw.foo.debug (e.g. hw.hifn.debug)
2003-03-11 22:47:06 +00:00
Sam Leffler
bd17515b68 gack; revert previous commit; not only did I read things backward but
I was in the wrong tree
2003-03-11 22:23:19 +00:00
Sam Leffler
44cc7634a3 sync with current: reduce default maxbatch setting from 5 to 1
Reviewed by:	re (sort of, consider this part of my previous request)
2003-03-11 22:20:43 +00:00