Mark Dawson holds teh copyright on this and has releases from
Compaq to allow him to do so..
Not functional in 4.0 yet but being checked in to allow the functional
3.x version to be branched at this point.
|revision 1.13
|date: 1995/09/15 23:49:23; author: davidg; state: Exp; lines: +15 -2
|Check for page being resident when doing I/O with /dev/kmem and return
|EFAULT if it is not resident. This prevents the system from manufacturing
|a zero-fill page for unused but allocated areas of the kernel's VM.
writing, we want to be able to read the buffer. If we're reading, we want
to be able to write to the buffer.
PR: kern/11870
Submitted by: Andrew Mobbs <amobbs@allstor-sw.co.uk>
This is an old OPTi chipset.
If you use a Bt878 card with this chipset, be sure to enable
the SIS/VIA chipset compatiblity mode workaround.
Tested By: Ben Laurie <ben@algroup.co.uk>
SIS/VIA/ OPTi chipset PCI bus workarounds.
These make the Bt878/879 chips stabler on certain
older and non-intel motherboards.
Use options BKTR_430_FX_MODE
or options BKTR_SIS_VIA_MODE
to enable these modes.
Also rename 849 to 849A
in the transmit code: the TX descriptor ring, and a 'shadow' ring of mbuf
pointers, one for each TX descriptor. When transmitting a packet that
consists of several fragments in an mbuf chain, we link each fragment
to a descriptor in the TX ring, but we only save a pointer to the mbuf
chain. This pointer is saved in the shadow ring entry which corresponds
to the first fragment in the packet. Later, ti_txeof() can release the
whole chain with a single m_freem() call. (We need the second ring to
keep track of the virtual addresses of the mbuf chains.)
The problem with this is that the Tigon isn't actually through with the
mbuf chain until it reaches the last fragment (which has the TI_BDFLAG_END
bit set), however the current scheme releases the mbuf chain as soon as
the first fragment is consumed. This is wrong, since the mbufs can then
be yanked out from under the Tigon and modified before the other fragments
can be transmitted.
The fix is to make a one line change to ti_encap() so that it saves the
mbuf chain pointer in the shadow ring entry that corresponds to the last
fragment in TX ring instead of the first. This prevents the mbufs from
being released until the last fragment is transmitted.
Painstakingly diagnosed and fixed by: Robert Picco <picco@mail.wevinc.com>
Brought to my attention by: dg
+ add a missing call to dn_rule_delete() when flushing firewall
rules, thus preventing possible panics due to dangling pointers
(this was already done for single rule deletes).
+ improve "usage" output in ipfw(8)
+ add a few checks to ipfw pipe parameters and make it a bit more
tolerant of common mistakes (such as specifying kbit instead of Kbit)
PR: kern/10889
Submitted by: Ruslan Ermilov
manager and prevented IOPort allocation beyond the first EISA slot from
working. subr_rman.c should have trapped this on the way into the system
rather than tripping over the wreckage.
Head banged into wall repeatedly by: "Matthew N. Dodd" <winter@jurai.net>
if there is no character device associated with the block device. In this
case that doesn't matter because bdevvp() doesn't use the character
device structure.
I can use the pointy bit of the axe too.
on systems with no FFS.
- Remove all references to mfs from cpu_rootconf(). mfs_init is
called prior to cpu_rootconf(), so it can set mountrootfsname to mfs
and (more imporantly) set rootdev using the (bogus in Bruce's opinion)
special major number of 255.
- Fix an error message.
- Do the MFS_ROOT setting of mountrootfsname in mfs_init() instead of
cpu_rootconf().
- Set rootdev in mfs_init instead of later in mfs_mount() iff MFS_ROOT.
Honor the 'bus reset at startup' option now that the XPT properly
handles transfer negotiation in this scenario.
Honor the sync rate settings on Ultra2 controllers. We would
always negotiate at the fastest speed. Oops.
aic7xxx.h:
Whitespace.
aic7xxx.seq:
Fix a minor nit that would cause the controller to miss the update
of the negotiation required bitmask causing the negotiation to
be delayed by a command.
code in all initiator type peripheral drivers.
scsi_target.c:
Release ATIO structures that wind up in the 'unkown command queue'
for consumption by our userland counterpart, back to the controller
when the exception for that command is cleared.
types allow the reporting of error counts and other statistics. Currently
we provide information on the last BDR or bus reset as well as active
transaction inforamtion, but this will be expanded as more information is
added to aid in error recovery.
Use the 'last reset' information to better handle bus settle delays.
Peripheral drivers now control whether a bus settle delay occurs and
for how long. This allows target mode peripheral drivers to avoid
having their device queue frozen by the XPT for what shoudl only be
initiator type behavior.
Don't perform a bus reset if the target device is incapable of performing
transfer negotiation (e.g. Fiber Channel).
If we don't perform a bus reset but the controller is capable of transfer
negotiations, force negotiations on the first transaction to go to the
device. This ensures that we aren't tripped up by a left over negotiation
from the prom, BIOS, loader, etc.
Add a default async handler funstion to cam_periph.c to remove duplicated
code in all initiator type peripheral drivers.
Allow mapping of XPT_CONT_TARGET_IO ccbs from userland. They are
itentical to XPT_SCSI_IO ccbs as far as data mapping is concerned.
driver lacks error recovery and still needs more testing, but it's
about time I got it under revision control.
Submitted by: Tekram Inc.
Bus Space/DMA and cleanup: gibbs
- Mention that the 6Mbps turbo adapters are supported in HARDWARE.TXT
and RELNOTES.TXT and the wi.4 man page
- Mention turbo adapters in the wicontrol.8 man page and provide a
complete table of available transmit speed settings
* Re-work the resource allocation code to use helper functions in subr_bus.c.
* Add simple isa interface for manipulating the resource ranges which can be
allocated and remove the code from isa_write_ivar() which was previously
used for this purpose.
