<string.h> isn't supposed to be used by the kernel.
cronix.h is <machine/cronix.h>, not "cronyx.h" (ambiguous) or
<sys/cronyx.h> (nonexistent; caused compile to fail).
cxreg.h is <i386/isa/cxreg.h>, not "cxreg.h".
<i386/isa/cpufunc.h> shouldn't be included directly; it is always
included by <sys/systm.h>.
<i386/include/*.h> is <machine/*.h>
<systm.h> is <sys/systm.h>.
<kernel.h> is <sys/kernel.h>.
<bpfilter.h> is "bpfilter.h". It really is in the current directory.
>Description:
If a process attempts to open a floppy tape device when the
device has been configured in the kernel, but did not probe and attach
on bootup, then a panic will occur.
[Review: The current ft situation is a crock, and this only bandaids
an earlier wound inflicted by making the attach conditional. This urgently
requires a review]
Submitted by: gene
Keep track of interrupt nesting level. It is normally 0
for syscalls and traps, but is fudged to 1 for their exit
processing in case they metamorphose into an interrupt
handler.
i386/genassym.c;
Remove support for the obsolete pcb_iml and pcb_cmap2.
Add support for pcb_inl.
i386/swtch.s:
Fudge the interrupt nesting level across context switches and in
the idle loop so that the work for preemptive context switches
gets counted as interrupt time, the work for voluntary context
switches gets counted mostly as system time (the part when
curproc == 0 gets counted as interrupt time), and only truly idle
time gets counted as idle time.
Remove obsolete support (commented out and otherwise) for pcb_iml.
Load curpcb just before curproc instead of just after so that
curpcb is always valid if curproc is. A few more changes like
this may fix tracing through context switches.
Remove obsolete function swtch_to_inactive().
include/cpu.h:
Use the new interrupt nesting level variable to implement a
non-fake CLF_INTR() so that accounting for the interrupt state
works.
You can use top, iostat or (best) an up to date systat to see
interrupt overheads. I see the expected huge interrupt overheads
for ISA devices (on a 486DX/33, about 55% for an IDE drive
transferring 1250K/sec and the same for a WD8013EBT network card
transferring 1100K/sec). The huge interrupt overheads for serial
devices are unfortunately normally invisible.
include/pcb.h:
Remove the obsolete pcb_iml and pcb_cmap2. Replace them by
padding to preserve binary compatibility.
Use part of the new padding for pcb_inl.
isa/icu.s:
isa/vector.s:
Keep track of interrupt nesting level.
used as an address value. Then all comparisons should be done unsigned
and not signed. Fix it with a typecast of u_quad_t.
Error can be demonstrated with the current bash in port, do a
ulimit -s unlimited and the machine hangs. bash delivers through
an internal error a large negative value for the stacksize, the
comparison saw this smaller than MAXSSIZ and then tried to expand
the stack to this size.
Now floppy tape support is *disabled* unless you specifically
request otherwise. Poul wanted it this way, and I guess I'm not going to argue
though it may seem counter-intuitive. We can always change it back, later.
make the sequencer code fully compatible with the aic7870 (ie 294x adaptors).
I've also added to my local mods putting the sequencer into "FASTMODE" clock.
This gives upwards of 2M/sec write preformance improvement in some scenarios.
There haven't been any reports of this causing problems, and I have been
reaping the benifits of it for more than a week now.
This also includes a new version of the pre-generated file <ugh>
Obtained from: John Aycock (aycock@cpsc.ucalgary.ca) and myself
flags & 0x1. Somebody should build a kernel with this and see if
the floppy-tape damaged people can turn it off properly with userconfig.
I can't reproduce the original problem here.
This should have been disabled for some time, but I had screwed up ...
This made spurious values appear for fd0 in systat, when there was
NCR SCSI activity.
comconsole will behave as expected. The true problem should be fixed
instead, Bruce' comment for this:
>Anyway, i found the reason for my problems: somehow, ICRNL isn't in
>effect at `userconfig' time (but only for comconsole?), hence only
ICRNL doesn't apply to cngetc(). cnputc() unconditionally does the
equivalent of ONLCR; perhaps cngetc() should unconditionally do the
equivalent of ICRNL. Ddb must be checking for CR. Userconfig only
checks for NL. Userconfig works with syscons because pccngetc()
does the conversion. This is probably the wrong place to do it.
Allow chown() to return success if the gid isn't changed even if
the gid is not the caller's. Such gids are normal for files created
in world-writable directories sucj as /tmp. This "fixes" annoying
error messages for mv'ing files created in /tmp to another file
system. mv still preserves the foreign gid of /tmp, but now does
it silently.
operation of each clist. Limit the growth of each clist. Clists
can only grow larger than the reserved minimum if there are free
cblocks in a shared pool. The size of this pool is now fixed
(this could be improved). The reserved and maximum sizes are more
carefully allocated for slip and ppp, depending on the mtu. A maximum
MTU of 16384 is now enforced for ppp.
1. The pageout daemon used to block under certain
circumstances, and we needed to add new functionality
that would cause the pageout daemon to block more often.
Now, the pageout daemon mostly just gets rid of pages
and kills processes when the system is out of swap.
The swapping, rss limiting and object cache trimming
have been folded into a new daemon called "vmdaemon".
This new daemon does things that need to be done for
the VM system, but can block. For example, if the
vmdaemon blocks for memory, the pageout daemon
can take care of it. If the pageout daemon had
blocked for memory, it was difficult to handle
the situation correctly (and in some cases, was
impossible).
2. The collapse problem has now been entirely fixed.
It now appears to be impossible to accumulate unnecessary
vm objects. The object collapsing now occurs when ref counts
drop to one (where it is more likely to be more simple anyway
because less pages would be out on disk.) The original
fixes were incomplete in that pathological circumstances
could still be contrived to cause uncontrolled growth
of swap. Also, the old code still, under steady state
conditions, used more swap space than necessary. When
using the new code, users will generally notice a
significant decrease in swap space usage, and theoretically,
the system should be leaving fewer unused pages around
competing for memory.
Submitted by: John Dyson
and into ether_input(). It was silly to have bpf want this one way and
ether_input want it another way. Ripped out trailer support from the few
remaining drivers that still had it.
1) make #includes correct
2) fix bugs in address check macros
3) fixed bugs in, and enabled, recopy if heavily fragmented code
4) moved call to bpf tap to be before enqueing packet (probably gratuitous)
5) fixed bug that caused "abnormal interrupt" at boot time/first use
6) added support for reading Zynx address ROM
7) fixed bug that caused broadcasts to not work shortly after booting (only
manifested if not using multicast - e.g. not in FreeBSD 2.0)
8) fixed spelling errors in comments
Submitted by: Matt Thomas
Subject: Mea culpa -- small fix for netboot fixes
In accordance with the unavoidable principle sof Murphy's Law, I discovered
that the fixes I recently contributed for the netboot code had some small
flaws in them. Two of them were just typos and had no effect on how the
program functioned. The other one was a missing line from the rootopts and
swapopts functions I created in bootmenu.c, which was supposed to initialize
the NFS sotype flag. It defaults to UDP, and you can change it to TCP with
the rootopts or swapopts commands, but then you can't change it back again.
I originally had a line at the top of each function to reinitialize this
flag, but somehow it got lost in the shuffle, probably because I don't
actually have a need for that flag yet.
Submitted by: wpaul
That was the good news. The bad news is that bad144 is a proper mess,
and I don't have time to fix it now, so you will probably not be able to
use it anyway.
Sorry guys, go out and buy a 100Mb IDE drive and a paddleboard :-(
If somebody wants to pick up on this: bad144 needs to learn how to
stay inside our slice of the disk. That's the trick.
Go to a single dependancy in files.i386. Using a .c file for the
sequencer code won't work since I need to know the size of the program,
so we just include the generated .h file as:
"../../sys/gnu/misc/aic7770/aic7770_seq.h"
Reviewed by:
Submitted by:
Obtained from:
instead. The entire scheme just doesn't work as envisioned (hint: think
about make depend as well as all). Those extremely rare individuals who
actually hack on the sequencer code will know how to keep stuff in sync,
I *do* get the feeling!
Somehow, I don't think this stuff was tested at all! :-(
I really hope that it actually works, though my hopes are steadily diminishing.
Anyone with 27xx/28xx boards in -current is *strongly encouraged* to give this
stuff a shot! Otherwise, I suspect that we'll be punting this out of
2.0. I haven't found a single part of Justin's commit that wasn't broken
in some way.
of config so YOU MUST RECOMPILE CONFIG. Modifying config was the cleanest
solution to integrating this driver into the tree which will become more
obvious in the next commit.
a discussion going on about removing this code from the burden of the
GPL, but it won't happen before Beta, and this code should be tested
before release.
Supports 27/2842 class adaptec cards and is almost capable of supporting
aic7870 based adapters (294X series cards). It does not support Wide
controllers or the second channel on Twin boards although I have work in
progress on getting both channels and running.
I have also added a few performance improvements to this version that give
us approximately a 25% boost over the original driver. These patches have
been submitted to the author.
Obtained from: Linux aic7770 driver (John Aycock - aycock@cpsc.ucalgary.ca)
Smack the netboot program around so that it will allow the user to
specify mount options. [So that you can boot from a privileged port]
Change the default boot image name in netboot to /kernel, then strip
the leading slash when actually going out to get the NFS file handle.
Added support for 3Com 3c503 cards. Also added another command to
the (trans) that allows you to switch the 3Com's on-board transceiver
on and off. (ether.c, ether.h, bootmenu.c)
Modified the Makefile to support new compile-time options for 3c503
cards:
-DINCLUDE_3COM Include support for 3c503
-D_3COM_BASE=0x300 Define 3c503 base i/o address (if not
specified, 0x300 is the default)
-D_3COM_USE_AUI Disable the 3c503's transceiver by
default (without this flag the transceiver
is on by default)
buffering scheme and make it more in tune with FreeBSD's vfs_bio
implementation. The filesystem seems fairly stable, but I wouldn't recommend
it to anyone not willing to experience problems. This is very green code and
has the limitation that YOU CAN ONLY HAVE ONE LFS PARTITION MOUNTED AT A TIME.
What LFS is good for:
Non fsynced writes FASTER THAN FFS
Large deletions Increadibly fast
Reads are a little bit slower than FFS right now, but that is a factor of
how under optimized this code is. LFS should in theory perform at least as
well as FFS under fsync (iozone) type loads, and this is what I'm currently
working on.
Reviewed by: Justin Gibbs
Submitted by: John Dyson
Obtained from:
stages of debugging LFS:
* if we can't bmap, use old VOP code
*/
! if (/* (vp->v_mount && vp->v_mount->mnt_stat.f_type == MOUNT_LFS) || */
! VOP_BMAP(vp, foff, &dp, 0, 0)) {
for (i = 0; i < count; i++) {
if (i != reqpage) {
vnode_pager_freepage(m[i]);
--- 804,810 ----
/*
* if we can't bmap, use old VOP code
*/
! if (VOP_BMAP(vp, foff, &dp, 0, 0)) {
Reviewed by: gibbs
Submitted by: John Dyson
was supposed to have already been made, but got botched somewhere.
Don't clobber the last page of memory (where the message buffer is). Some
BIOS don't gratuitously wipe it out on reboot.
Remove bogus declaration of Debugger(). Call Debugger() even if DDB is
not defined, but still call panic() after Debugger() returns, although
most other SCSI drivers just call Debugger().
printf() is inconsistent with the prototype for the library printf() and
gets declared if DIAGNOSTIC is defined because <vm/vm_page.h> includes
<sys/systm.h>.
Change the sc_link structure from 8 targets with 8 lun's to
16 targets with 8 lun's. Wide scsi and the ncr 825 does support 16 targets.
scsiconf.c:
move the addition of the trailing NUL's out of a then clause, they are also
needed in the else clause for an unknown device.
Alphabetize.
Write all i/o functions in sleep so that we don't use anything from
NetBSD.
Restore the correct type of u_int for ports. This saves a whole cycle
per i/o on 486's.
Change `inline' back to __inline to avoid compiler warnings with
-Wreally-all.
Don't implement bdb() unless BDE_DEBUGGER is defined. Declare bdb_exists
outside the function to avoid hundreds of compiler warnings.
Let the compiler pick the register in asms if possible.
Implement ffs() using inline asm(). gcc provides a slightly different
one. It was broken in gcc-2.4.5 but works now. Declaring a correct
version inline ensures getting a correct version. FreeBSD-1.1.5 has
an slow inline version but FreeBSD-2.0 has a library version (which
probably never gets used).
Do inb() and outb() without using %edx for constant ports below 0x100.
Remove casts to the same type in queue functions.
Declare prototypes for everything implemented i386/*.s and also for
everything that is normally implemented as an inline here (I don't
like the current complete dependency on gcc). Ifdef out the prototypes
that are declared elsewhere. THere should be a separate header to
declare things implemented in i386/*.s, but then it would be harder
to override declarations with inlines.
${UII}
with the current default exception (un)mask. There should be no such
processes unless you change the mask. Someday the mask should be
changed to the IEEE default of everything masked. The npx state
gets saved so that it can be checked and this may have the side effect
of fixing a bug that was reported for 1.1.5. (npx exceptions may
sometimes leak across exits and clobber another process. I can't see
how this can happen.)
Get some missing/wrong declarations from headers now that the headers
have them.
I couldn't find a better way to avoid compiler warnings about
redundant and/or inconsistent declaration of ffs(). I'd like to
be able to declare prototypes in general headers without committing
to implementing them as `static inline' or `extern', but there
seems to be no way to do this with gcc-2.6.1. E.g.,
int foo(void);
static __inline int foo(void) { return 1; }
causes a warning about the linkage mismatch, while the opposite
order causes a warning about the redundant declaration.
the following.
Move declarations to and from <machine/segments.h>. Make segment stuff
static if possible.
Remove unused (although initialized) global variables _default_ldt,
currentldt, _gsel_tss (rename the latter to the auto variable
gtel_tss).
Use "correct" and consistent types for interrupt handlers.
Remove a mailing address from the code.
Fix type mismatches found by adding prototypes.
Partly support BDE_DEBUGGER. Still broken by conflict with APM. Does
nothing if BDE_DEBUGGER is not defined.
Clean up prototypes and data declarations. Declare most of the segment
functions that are implemented in support.s. Make data private in
machdep.c if possible.
Parenthesize expressions in macros properly!
${Uniformize idempotency ifdef}.
to avoid compiler warnings.
Clean up prototypes: alphabetize; don't use redundant `extern' or
meaningless `extern inline'.
Uniformize idempotency ifdef.
(These functions are implemented in assembler so the compiler can't
check the declarations.)
Clean up prototypes: restore CSRG's alphabetical order, arg names in
prototypes, formatting to fit in 80 columns
Declare a complete prototype for the function pointer *ifa_rtrequest.
radix.h:
Declare a complete prototype for the function pointer *rnh_walktree
and for the function rn_walktree.
Uniformize idempotency ifdef.
Disable the bogus declaration of pmap_bootstrap(). Since its arg list
is machine-dependent, it must be declared in a machine-dependent header.
vm_page.h:
Change `inline' to `__inline' and old-style function parameter lists for
inlined functions to new-style.
`inline' and old-style function parameter lists should never be used in
system headers, even in very machine-dependent ones, because they cause
warnings from gcc -Wreally-all.
get truncated to LONG_MAX. Don't lobotomize the merged library source.
Make all private data static.
Use int_parms for the i/o "address" since the "address" is really a number
and is represented as an int.
Add command `flags' to allow changing device flags.
Fix scrolling of device listing. Only scrolling of the current devtab
was controlled. Reprint the header after scrolling.
Rename commands and change strings to match their config(8) keywords:
io -> port
IOaddr -> port
mem -> iomem (abbreviation is io :-()
MemAddr -> iomem
case changes
Don't use NULL for ASCII NUL.
Call strtoul() with base 0 for both numbers and addresses so that input
is consistent and hex and octal can be used for numbers.
Fix entry of irq number. Check the range at no extra cost. It wasn't
possible to enter irq -1.
Format device listing better. Large numbers (such as 0xffffffff for the
GENERIC lpt0 port) messed up the formatting.
Show the unit number in the device listing. Comment about the fields
that aren't shown.
fault was at offset 0 in the object. This resulted in more overhead but
was othewise benign. Added incore() check in vnode_pager_has_page()
to work around a problem with LFS...other than slightly higher overhead,
this change has no affect on UFS.
put the stuff into the right "distribution". As default things end up
in "bindist".
Normal (ie: most) makefiles know naught of this.
More commits will follow, which will direct various parts of the tree
into the distribution we want them in.
Some of the grief of being release-engineer is supposed to go away with this.
of the 1.1.5 driver, a recent version of the NetBSD driver, Andres'
transmission start threshold code, and all other relavent changes to the driver
since it was brought into 2.0. The multicast support from NetBSD has not be
folded in yet. I've tested it under high loads for two weeks and it is now
robust enough to be included in the GENERIC kernel.
Reviewed by: gibbs
Submitted by: vega@sophia.inria.fr (Andres Vega Garcia)
scsi adapter. Let it work on every adapter. Someone want to rewrite
this to be coupled with the adapter specification in the config file,
so that you can say which adapters need it ?
cosmetique) because we already have right things there or his changes
are incorrect.
Fix mcd_subchan to return position, inspired by idea from
bugress@s069.infonet.net, but different implementation.
Here is the improved probe for the mse (Bus Mouse) device driver. I
have been running with this under 1.1.5.1 as well as 2.0 without a hitch for
quite a while.
Submitted by: lars
device announcement; assume a sector size of 512 instead (likely to be
right at all).
This case happens when booting with a removable disk device attached
(e.g. an MOD), but no medium inserted.
I think it's time for Ugen to get a freefall account, just so I can
direct mail at him directly and let him drop off patches for us here. Ugen?
Done!
Submitted by: ugen
Somebody should make a mib variable for it.
Just now it is pointless to dump the kernel, since we have nothing which
can read the dump.
Furthermore is should never be the default to dump.
options DODUMP
will enable dumps.