This makes 'stop' behave consistently with 'start' in the script.
Also use $SYSCTL instead of sysctl for consistency within that script.
MFC after: 3 weeks
Always create loopback routes on every fib, for both IPv4 and IPv6
etc/rc.d/routing
Create loopback IPv4 and IPv6 routes on every fib at boot. Revert
278302; now that all FIBs have IPv6 loopback routes, the
"route add -reject" commands won't fail.
tests/etc/rc.d/routing_test.sh
Greatly simplify static_ipv6_loopback_route_for_each_fib. It was
written under the assumption that loopback routes would be added to
a given fib by the kernel as soon as an interface is configured on
that fib. However, the logic can be much simpler now that we simply
add loopback routes to all fibs at boot. This also removes the need
to run the test as root, removes the restriction that
net.add_addr_allfibs=0, and removes the need to configure fibs in
kyua.conf.
Also, add a test case for IPv4 loopback routes
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D6582
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
The following warnings were displayed:
sysctl: net.inet.ip.sourceroute=0: Operation not permitted
sysctl: net.inet.ip.accept_sourceroute=0: Operation not permitted
IPX was a network transport protocol in Novell's NetWare network operating
system from late 80s and then 90s. The NetWare itself switched to TCP/IP
as default transport in 1998. Later, in this century the Novell Open
Enterprise Server became successor of Novell NetWare. The last release
that claimed to still support IPX was OES 2 in 2007. Routing equipment
vendors (e.g. Cisco) discontinued support for IPX in 2011.
Thus, IPX won't be supported in FreeBSD 11.0-RELEASE.
{,ipv6_}static_routes and rc.d/routing. For example:
static_routes="foo bar:em0"
route_foo="-net 10.0.0.0/24 -gateway 192.168.2.1"
route_bar="-net 192.168.1.0/24 -gateway 192.168.0.2"
At boot time, all of the static routes are installed as before.
The differences are:
- "/etc/rc.d/netif start/stop <if>" now configures static routes
with :<if> if any.
- "/etc/rc.d/routing start/stop <af> <if>" works as well. <af> cannot be
omitted when <if> is specified, but a keyword "any" or "all" can be used
for <af> and <if>.
apply to most jails but do apply to vnet jails. This includes adding
a new sysctl "security.jail.vnet" to identify vnet jails.
PR: conf/149050
Submitted by: mdodd
MFC after: 3 days
for the default FIB followed by a statement with a list of FIB numbers for
all the other FIBs we install the routes for.
Request by: kib (to make it less noisy)
Tested by: kib
MFC after: 3 days
Print a separate "Additional routing options" line for each address family
which has additional options, so that it does not get mixed up with the
output from adding routes.
This also reverts r224048 which added newlines to two arbitrary routing
options.
for each address family. Replace AF_static() with static_AF() for
consistency.
- Display a message only if the user sets a non-default value, and set
a sysctl explicitly even if it is the default value.
an IPv6 support.
Reported by: Alexander Best <alexbestms__at__math.uni-muenster.de>
Confirmed by: Paul B. Mahol <onemda__at__gmail.com>,
Alexander Best <alexbestms__at__math.uni-muenster.de>
legacy IP handling rather than the IPv6 version.
Reported by: Pegasus Mc Cleaft (ken mthelicon.com)
Tested by: Pegasus Mc Cleaft (ken mthelicon.com)
MFC after: 2 days
X-MFX with: r197139
- Add rc.d/stf and rc.d/faith for stf(4) and faith(4).
- Remove rc.d/auto_linklocal and rc.d/network_ipv6.
- Move rc.d/sysctl to just before FILESYSTEMS because rc.d/netif
depends on some sysctl variables.
Reviewed by: brooks
MFC after: 3 days
non-dhcp interfaces to negotiate/associate this will make more sense.
This also correctly gets run after both devd and netif are run so it has
a chance of working.
The rcorder(8) condition PROVIDE'd by the script
and REQUIRE'd by the others becomes "ppp".
The ultimate goal of the transformation is to reduce
confusion resulting from the fact that $name has been
"ppp" already.
Discussed with: pjd, -rc
use the atmconfig(8) utility instead of route(8) to install those routes.
For this we need a new rc.conf variable natm_static_routes that works
just like static_routes except that the referenced routes use the syntax
of atmconfig(8).
Okay'ed by: mtm
o Change the provider names.
o Separate routing into two parts: static routing and routing options. The
start command will run both parts, but they can be run separately using
the static and options command, respectively:
(/etc/rc.d/routing static; /etc/rc.d/routing options)
while. This is only the script pieces, the glue for the build comes next.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
Reviewed by: silence on -current and -hackers
Prodded by: rwatson
was apparently smoking something when I committed the last fix, because as
ume was kindly enough to set me straight on, amd *will* start with no
arguments at all, as long as there is an /etc/amd.conf file for it to
read. What it won't do is start with *just* -p.
In any case, now it's fixed.
only doing ipnat(8). Go back to using $ipfilter_active, but turn off
$ipfilter_active when loading ipl.ko has failed.
Submitted by: devet@devet.org (Arjan de Vet)
MFC after: 3 days
conf file, or command line options. I brought this up in PR 12432,
which (ironically) obrien assigned to me after I became a committer. :)
PR: conf/12432
Submitted by: Me
