These CPUs use an enhanced layout of the interrupt vector dispatch
and dispatch status registers in order to allow sending IPIs to
multiple targets simultaneously. Thus support for these CPUs was
put in a newly added cheetah_ipi_selected(). This is intended to
be pointed to by cpu_ipi_selected, which now is a function pointer,
in order to avoid cpu_impl checks once booted. Alternatively it
can point to spitfire_ipi_selected(), which was renamed from
cpu_ipi_selected(). Consequently cpu_ipi_send() was also renamed
to spitfire_ipi_send() (there's no need for a cheetah equivalent
of this so far). Initialization of the cpu_ipi_selected pointer
and other requirements is done in mp_init(), which was renamed
from mp_tramp_alloc(), as cpu_mp_start() isn't called on UP
systems while cpu_ipi_selected() is. As a side-effect this allows
to make mp_tramp static to sys/sparc64/sparc64/mp_machdep.c.
For the sake of avoiding #ifdef SMP and for keeping the history in
place cheetah_ipi_selected() and spitfire_ipi_{selected,send}()
where not put into/moved to sys/sparc64/sparc64/{cheetah,spitfire}.c
- Add some CTASSERTs and KASSERTs ensuring that MAXCPU doesn't
exceed the data types we use to store the CPU bit fields or the
number of USIII and greater CPUs supported by the current
cheetah_ipi_selected() implementation (which for JBus-CPUs is
only 4; that should be fine though as according to OpenSolaris
there are no sun4u machines with more than 4 JBus-CPUs).
- In cpu_mp_start() don't enumerate and start more than MAXCPU CPUs
as we can't handle more than that.
- In cpu_mp_start() check for upa-portid vs. portid depending on
cpu_impl for consistency with nexus(4).
- In spitfire_ipi_selected() add KASSERTs ensuring that a CPU isn't
told to IPI itself as sun4u CPUs just can't do that.
- In spitfire_ipi_send() do a MEMBAR #Sync after writing the
interrupt vector data as we want to make sure the payload was
actually written before we trigger the dispatch.
- In spitfire_ipi_send() also verify IDR_BUSY when checking whether
the dispatch was successful as it has to be cleared for this to
be the case.
- Remove some redundant variables.
caches with data caches after writing to memory. This typically
is required to make breakpoints work on ia64 and powerpc. For
those architectures the function is implemented.
- Rename PCPU_LAZY_INC into PCPU_INC
- Add the PCPU_ADD interface which just does an add on the pcpu member
given a specific value.
Note that for most architectures PCPU_INC and PCPU_ADD are not safe.
This is a point that needs some discussions/work in the next days.
Reviewed by: alc, bde
Approved by: jeff (mentor)
referenced outside of mp_machdep.c
- Replace a magic 14 with the newly added IDC_ITID_SHIFT macro.
- Remove the global mp_boot_mid variable as it's not really necessary
and just replacing it with PCPU_GET(mid) doesn't have any impact on
performance once booted.
- Replace PCPU_GET(cpuid) with the curcpu shortcut.
- Replace hardcoded function names in panic strings etc with __func__
so they don't need to be updated when renaming the function.
- Use register_t instead of u_long for variables used to hold the
return value of intr_disable() so we don't need to apply any
knowledge about the actual width of that value here.
- Improve the wording of some comments.
- Fix several style(9) bugs.
- Use __FBSDID in identcpu.c.
- Remove #ifndef SUN4V around global cpu_impl variable; it doesn't
hurt on sun4v for now and once setPQL2() is gone sun4v can stop
sharing identcpu.c with sparc64, making the reminder of this file
also sparc64-only again. [1]
Submitted by: kmacy [1]
VM_PHYSSEG_SPARSE depending on whether the physical address space is
densely or sparsely populated with memory. The effect of this
definition is to determine which of two implementations of
vm_page_array and PHYS_TO_VM_PAGE() is used. The legacy
implementation is obtained by defining VM_PHYSSEG_DENSE, and a new
implementation that trades off time for space is obtained by defining
VM_PHYSSEG_SPARSE. For now, all architectures except for ia64 and
sparc64 define VM_PHYSSEG_DENSE. Defining VM_PHYSSEG_SPARSE on ia64
allows the entirety of my Itanium 2's memory to be used. Previously,
only the first 1 GB could be used. Defining VM_PHYSSEG_SPARSE on
sparc64 allows USIIIi-based systems to boot without crashing.
This change is a combination of Nathan Whitehorn's patch and my own
work in perforce.
Discussed with: kmacy, marius, Nathan Whitehorn
PR: 112194
vm.kmem_size_min. Useful when using ZFS to make sure that vm.kmem size will
be at least 256mb (for example) without forcing a particular value via vm.kmem_size.
Approved by: njl (mentor)
Reviewed by: alc
sun4v nexus(4) in turn is based on):
o Change nexus(4) to manage the resources of its children so the
respective device drivers don't need to figure them out of OFW
themselves.
o Change nexus(4) to provide the ofw_bus KOBJ interface instead of
using IVARs for supplying the OFW node and the subset of standard
properties of its children. Together with the previous change this
also allows to fully take advantage of newbus in that drivers like
fhc(4), which attach on multiple parent busses, no longer require
different bus front-ends as obtaining the OFW node and properties
as well as resource allocation works the same for all supported
busses. As such this change also is part 4/4 of allowing creator(4)
to work in USIII-based machines as it allows this driver to attach
on both nexus(4) and upa(4). On the other hand removing these IVARs
breaks API compatibility with the powerpc nexus(4) but which isn't
that bad as a) sparc64 currently doesn't share any device driver
hanging off of nexus(4) with powerpc and b) they were no longer
compatible regarding OFW-related extensions at the pci(4) level
since quite some time.
o Provide bus_get_dma_tag methods in nexus(4) and its children in
order to handle DMA tags in a hierarchical way and get rid of the
sparc64_root_dma_tag kludge. Together with the previous two items
this changes also allows to completely get rid of the nexus(4)
IVAR interface. It also includes:
- pushing the constraints previously specified by the nexus_dmatag
down into the DMA tags of psycho(4) and sbus(4) as it's their
IOMMUs which induce these restrictions (and nothing at the
nexus(4) or anything that would warrant specifying them there),
- fixing some obviously wrong constraints of the psycho(4) and
sbus(4) DMA tags, which happened to not actually be used with
the sparc64_root_dma_tag kludge in place and therefore didn't
cause problems so far,
- replacing magic constants for constraints with macros as far
as it is obvious as to where they come from.
This doesn't include taking advantage of the newbus way to get
the parent DMA tags implemented by this change in order to divorce
the IOTSBs of the PCI and SBus IOMMUs or for implementing the
workaround for the DMA sync bug in Sabre (and Tomatillo) bridges,
yet, though.
o Get rid of the notion that nexus(4) (mostly) reflects an UPA bus
by replacing ofw_upa.h and with ofw_nexus.h (which was repo-copied
from ofw_upa.h) and renaming its content, which actually applies to
all of Fireplane/Safari, JBus and UPA (in the host bus case), as
appropriate.
o Just use M_DEVBUF instead of a separate M_NEXUS malloc type for
allocating the device info for the children of nexus(4). This is
done in order to not need to export M_NEXUS when deriving drivers
for subordinate busses from the nexus(4) class.
o Use the DEFINE_CLASS_0() macro to declare the nexus(4) driver so
we can derive subclasses from it.
o Const'ify the nexus_excl_name and nexus_excl_type arrays as well
as add 'associations' and 'rsc', which are pseudo-devices without
resources and therefore of no real interest for nexus(4), to the
former.
o Let the nexus(4) device memory rman manage the entire 64-bit address
space instead of just the UPA_MEMSTART to UPA_MEMEND subregion as
Fireplane/Safari- and JBus-based machines use multiple ranges,
which can't be as easily divided as in the case of UPA (limiting
the address space only served for sanity checking anyway).
o Use M_WAITOK instead of M_NOWAIT when allocating the device info
for children of nexus(4) in order to give one less opportunity
for adding devices to nexus(4) to fail.
o While adapting the drivers affected by the above nexus(4) changes,
change them to take advantage of rman_get_rid() instead of caching
the RIDs assigned to allocated resources, now that the RIDs of
resources are correctly set.
o In iommu(4) and nexus(4) replace hard-coded functions names, which
actually became outdated in several places, in panic strings and
status massages with __func__. [1]
o Use driver_filter_t in prototypes where appropriate.
o Add my copyright to creator(4), fhc(4), nexus(4), psycho(4) and
sbus(4) as I changed considerable amounts of these drivers as well
as added a bunch of new features, workarounds for silicon bugs etc.
o Fix some white space nits.
Due to lack of access to Exx00 hardware, these changes, i.e. central(4)
and fhc(4), couldn't be runtime tested on such a machine. Exx00 are
currently reported to panic before trying to attach nexus(4) anyway
though.
PR: 76052 [1]
Approved by: re (kensmith)
headers in .S directly rather than getting to their macros through
genassym.c/assym.s so there are less headers genassym.c has to be
kept in sync with.
While at it fix some stytle(9) bugs (indentation, prototype format,
sort headers, etc) and remove trailing whitespace.
may also reflect a Fireplane/Safari or JBus bus (or a virtual bus which
in turn reflects a JBus bus or something like that...).
- In the both the sparc64 and sun4v bus_machdep.c use __FBSDID.
- Spell SBus the official way in comments.
- Replace hardcoded function names (all of which were actually outdated)
in panic and status strings with __func__.
- Fix whitespace nits.
and friends along with all hacks required to implement them. None of
the drivers currently built (as part of GENERIC, LINT or modules) on
sparc64 or sun4v and none of those we might want to use there in
future uses them, AFAICT there actually never was a driver hooked up
to the sparc64 or sun4v build that correctly used these functions
(and it looks like that due to a bug read{b,w,l}()/write{b,w,l}() and
the other functions working on a memory handle never actually worked on
sun4v). All they ever were good for on sparc64 and sun4v was erroneously
dragging in dependencies on isa(4) in drivers like f.e. dpt(4), si(4)
and syscons(4) in source files that supposedly were bus-neutral and
hiding issues with drivers like f.e. ng_bt3c(4) that used these
functions with busses other than isa(4) and therefore couldn't work on
these platforms.
argument in parentheses so these macros are safe to use and invocations
with an expression as the argument like __bswap32_const(42 << 23 | 13)
work as expected. Additionally, mask all the individually shifted bytes
as appropriate so the bytes which exceed the width of the respective
__bswapN_const() macro in invocations like __bswap16_const(0xdead600d)
are ignored like it's the case with the corresponding __bswapN_var()
function.
MFC after: 3 days
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
Security:
Move the relocation definitions to the common elf header so that DTrace
can use them on one architecture targeted to a different one.
Add the additional ELF types defines in Sun's "Linker and Libraries"
manual.
system's machine-dependent and machine-independent layers. Once
pmap_clear_write() is implemented on all of our supported
architectures, I intend to replace all calls to pmap_page_protect() by
calls to pmap_clear_write(). Why? Both the use and implementation of
pmap_page_protect() in our virtual memory system has subtle errors,
specifically, the management of execute permission is broken on some
architectures. The "prot" argument to pmap_page_protect() should
behave differently from the "prot" argument to other pmap functions.
Instead of meaning, "give the specified access rights to all of the
physical page's mappings," it means "don't take away the specified
access rights from all of the physical page's mappings, but do take
away the ones that aren't specified." However, owing to our i386
legacy, i.e., no support for no-execute rights, all but one invocation
of pmap_page_protect() specifies VM_PROT_READ only, when the intent
is, in fact, to remove only write permission. Consequently, a
faithful implementation of pmap_page_protect(), e.g., ia64, would
remove execute permission as well as write permission. On the other
hand, some architectures that support execute permission have
basically ignored whether or not VM_PROT_EXECUTE is passed to
pmap_page_protect(), e.g., amd64 and sparc64. This change represents
the first step in replacing pmap_page_protect() by the less subtle
pmap_clear_write() that is already implemented on amd64, i386, and
sparc64.
Discussed with: grehan@ and marcel@
moving the typedef of bus_space_tag_t from sys/sparc64/include/bus.h
to sys/sparc64/include/_bus.h. This brings sparc64 in sync with the
other platforms and fixes the compilation of drivers which include
<sys/rman.h> before <machine/bus.h> after sys/sys/rman.h rev. 1.34.
- Remove the definition of bus_type_t from sys/sparc64/include/_bus.h
as it's unused since sys/sparc64/include/bus.h rev. 1.6 and
sys/sparc64/sparc64/bus_machdep.c rev. 1.3.
- Remove some pointless comments.
Retire pmap_track_modified(). We no longer need it because we do not
create managed mappings within the clean submap. To prevent regressions,
add assertions blocking the creation of managed mappings within the clean
submap.
PCB in which the context of stopped CPUs is stored. To access this
PCB from KDB, we introduce a new define, called KDB_STOPPEDPCB. The
definition, when present, lives in <machine/kdb.h> and abstracts
where MD code saves the context. Define KDB_STOPPEDPCB on i386,
amd64, alpha and sparc64 in accordance to previous code.
operands are consumed so use the appropriate constraint modifier.
Before this change GCC used one register for both an input and an
unrelated output operand of in_addword(), causing the input to be
overwritten before it was consumed and thus breaking in_addword().
For in_cksum_hdr() and in_pseudo() this change is more or less
cosmetic.
- Fix a misspelling in a nearby comment.
Reported & tested by: yongari
MFC after: 1 week
passing a pointer to an opaque clockframe structure and requiring the
MD code to supply CLKF_FOO() macros to extract needed values out of the
opaque structure, just pass the needed values directly. In practice this
means passing the pair (usermode, pc) to hardclock() and profclock() and
passing the boolean (usermode) to hardclock_cpu() and hardclock_process().
Other details:
- Axe clockframe and CLKF_FOO() macros on all architectures. Basically,
all the archs were taking a trapframe and converting it into a clockframe
one way or another. Now they can just extract the PC and usermode values
directly out of the trapframe and pass it to fooclock().
- Renamed hardclock_process() to hardclock_cpu() as the latter is more
accurate.
- On Alpha, we now run profclock() at hz (profhz == hz) rather than at
the slower stathz.
- On Alpha, for the TurboLaser machines that don't have an 8254
timecounter, call hardclock() directly. This removes an extra
conditional check from every clock interrupt on Alpha on the BSP.
There is probably room for even further pruning here by changing Alpha
to use the simplified timecounter we use on x86 with the lapic timer
since we don't get interrupts from the 8254 on Alpha anyway.
- On x86, clkintr() shouldn't ever be called now unless using_lapic_timer
is false, so add a KASSERT() to that affect and remove a condition
to slightly optimize the non-lapic case.
- Change prototypeof arm_handler_execute() so that it's first arg is a
trapframe pointer rather than a void pointer for clarity.
- Use KCOUNT macro in profclock() to lookup the kernel profiling bucket.
Tested on: alpha, amd64, arm, i386, ia64, sparc64
Reviewed by: bde (mostly)
- Move vtophys() macros next to vtopte() where vtopte() exists to match
comments above vtopte().
- Remove references to the alternate address space in the comment above
vtopte(). amd64 never had the alternate address space, and i386 lost it
prior to PAE support being added.
- s/entires/entries/ in comments.
Reviewed by: alc
KTR_* class macros via genassym.c. Together with sys/sys/ktr.h
rev. 1.34 this has the desired side-effect of providing a default
value for KTR_COMPILE. Thus this fixes warnings from -Wundef
regarding KTR_COMPILE not being defined for .S files.
Requested by: ru
Reviewed by: ru
MACHINE_ARCH and MACHINE). Their purpose was to be able to test
in cpp(1), but cpp(1) only understands integer type expressions.
Using such unsupported expressions introduced a number of subtle
bugs, which were discovered by compiling with -Wundef.
from sys/sparc64/include/ofw_upa.h to sys/sparc64/pci/ofw_pci.h and
rename them to struct ofw_pci_ranges and OFW_PCI_RANGE_* respectively.
This ranges struct only applies to host-PCI bridges but no to other
bridges found on UPA. At the same time it applies to all host-PCI
bridges regardless of whether the interconnection bus is Fireplane/
Safari, JBus or UPA.
- While here rename the PCI_CS_* macros in sys/sparc64/pci/ofw_pci.h
to OFW_PCI_CS_* in order to be consistent and change this header to
use uintXX_t instead of u_intXX_t.
current context in the IPI_STOP handler so that we can get accurate stack
traces of threads on other CPUs on these two archs like we do now on i386
and amd64.
Tested on: alpha, sparc64
and increase flexibility to allow various different approaches to be tried
in the future.
- Split struct ithd up into two pieces. struct intr_event holds the list
of interrupt handlers associated with interrupt sources.
struct intr_thread contains the data relative to an interrupt thread.
Currently we still provide a 1:1 relationship of events to threads
with the exception that events only have an associated thread if there
is at least one threaded interrupt handler attached to the event. This
means that on x86 we no longer have 4 bazillion interrupt threads with
no handlers. It also means that interrupt events with only INTR_FAST
handlers no longer have an associated thread either.
- Renamed struct intrhand to struct intr_handler to follow the struct
intr_foo naming convention. This did require renaming the powerpc
MD struct intr_handler to struct ppc_intr_handler.
- INTR_FAST no longer implies INTR_EXCL on all architectures except for
powerpc. This means that multiple INTR_FAST handlers can attach to the
same interrupt and that INTR_FAST and non-INTR_FAST handlers can attach
to the same interrupt. Sharing INTR_FAST handlers may not always be
desirable, but having sio(4) and uhci(4) fight over an IRQ isn't fun
either. Drivers can always still use INTR_EXCL to ask for an interrupt
exclusively. The way this sharing works is that when an interrupt
comes in, all the INTR_FAST handlers are executed first, and if any
threaded handlers exist, the interrupt thread is scheduled afterwards.
This type of layout also makes it possible to investigate using interrupt
filters ala OS X where the filter determines whether or not its companion
threaded handler should run.
- Aside from the INTR_FAST changes above, the impact on MD interrupt code
is mostly just 's/ithread/intr_event/'.
- A new MI ddb command 'show intrs' walks the list of interrupt events
dumping their state. It also has a '/v' verbose switch which dumps
info about all of the handlers attached to each event.
- We currently don't destroy an interrupt thread when the last threaded
handler is removed because it would suck for things like ppbus(8)'s
braindead behavior. The code is present, though, it is just under
#if 0 for now.
- Move the code to actually execute the threaded handlers for an interrrupt
event into a separate function so that ithread_loop() becomes more
readable. Previously this code was all in the middle of ithread_loop()
and indented halfway across the screen.
- Made struct intr_thread private to kern_intr.c and replaced td_ithd
with a thread private flag TDP_ITHREAD.
- In statclock, check curthread against idlethread directly rather than
curthread's proc against idlethread's proc. (Not really related to intr
changes)
Tested on: alpha, amd64, i386, sparc64
Tested on: arm, ia64 (older version of patch by cognet and marcel)
amd64, and is a factor of 3 less than the value previously auto-sized on
a 12GB machine, which would cause an overflow in calculations involving the
maxbcache int, causing bufinit() to loop forever at boot.
Reviewed by: mlaier, peter
variable and returns the previous value of the variable.
Tested on: i386, alpha, sparc64, arm (cognet)
Reviewed by: arch@
Submitted by: cognet (arm)
MFC after: 1 week
it to __MINSIGSTKSZ. Define MINSIGSTKSZ in <sys/signal.h>.
This is done in order to use MINSIGSTKSZ for the macro PTHREAD_STACK_MIN
in <pthread.h> (soon <limits.h>) without having to include the whole
<sys/signal.h> header.
Discussed with: bde
in the arm __swp() and sparc64 casa() and casax() functions is actually
being used as an input and output and not just the value of the register
that points to the memory location. This was the underlying source of
the mbuf refcount problems on sparc64 a while back. For arm this should be
a nop because __swp() has a constraint to clobber all memory which can
probably be removed now.
Reviewed by: alc, cognet
MFC after: 1 week
variables rather than void * variables. This makes it easier and simpler
to get asm constraints and volatile keywords correct.
MFC after: 3 days
Tested on: i386, alpha, sparc64
Compiled on: ia64, powerpc, amd64
Kernel toolchain busted on: arm
- Implement sampling modes and logging support in hwpmc(4).
- Separate MI and MD parts of hwpmc(4) and allow sharing of
PMC implementations across different architectures.
Add support for P4 (EMT64) style PMCs to the amd64 code.
- New pmcstat(8) options: -E (exit time counts) -W (counts
every context switch), -R (print log file).
- pmc(3) API changes, improve our ability to keep ABI compatibility
in the future. Add more 'alias' names for commonly used events.
- bug fixes & documentation.
