The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
While 80P80 is less likely to be used, VHT160 (a single contiguous
width) is harder to acquire but also preferable so return that first.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D35977
Correct IEEE80211_FEXT_BITS adding the missed one and move the later
one further. This will actually make VHT to show.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D35977
Introduce (*iv_update_bss)() with a default implementation to allow
drivers to overload/intercept the time when we swap iv_bss.
This helps firmware based drivers to synchronize state with firmware.
Otherwise, for some state changes, we begin with one ni (and in
LinuxKPI lsta) and try to finish with another ni (and a new lsta
in different state) and may no longer have access to the previous state.
This also saves us from constantly checking for ni changes complicating
code.
No functional changes intended.
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
X-MFC: move (*iv_update_bss) to spare area
While debugging is very good in net80211, some log messages are
repeated in multiple places 1:1. In order to distinguish where the
discard happened and to speed up analysis, add __func__:__LINE__
information to all these messages.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Implement two macros IEEE80211_VHTCAP_SUPP_CHAN_WIDTH_IS_160MHZ()
and its 80+80 counter part to check in vhtcaps for appropriate
levels of support and use the macros throughout the code.
Add vht160_chan_ranges/is_vht160_valid_freq and handle analogue
to vht80 in various parts of the code.
Add ieee80211_add_channel_cbw() which also takes the CBW flag
fields and make the former ieee80211_add_channel() a wrapper to it.
With the CBW flags we can add HT/VHT channels passing them to
getflags() for the 2/5ghz functions.
In ifconfig(8) add the regdomain_addchans() support for VHT160
and VHT80P80.
With this (+ regdoain.xml updates) VHT160 channels can be
configured, listed, and pass regdomain where appropriate.
Tested with: iwlwifi
Reviewed by: adrian
MFC after: 10 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26712
We have (two versions) of MS() and SM() macros which we use throughout
the wireless code. Change all but three places (ath_hal, rtwn, and rsu)
to the newly provided _IEEE80211_MASKSHIFT() and _IEEE80211_SHIFTMASK()
macros. Also change one internal case using both _S and _M instead of
just _S away from _M (one of the reasons rtwn and rsu were not changed).
This was done semi-mechanically. No functional changes intended.
Requested by: gnn (D26091)
Reviewed by: adrian (pre line wrap)
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC (d/b/a "Netgate")
Differential Revision: https://reviews.freebsd.org/D26539
For ieee80211_add_channel+*() we are passing in an int flag for
ht40 and in some cases another int flag for vht80 where we'd only
need two bits really.
Convert these variables to a bitflag and fold them together into one.
This also allows for VHT160 and VHT80P80 and whatever may come to
be considered. Define the various options currently needed.
Change the drivers (rtwn and rsu) which actually set this bit to non-0.
For convenience the "1" currently used for HT40 is preserved.
Enahnce getflags_5ghz() to handle the full set of VHT flags based
on the input flags from the the driver.
Update the regdomain implementation as well to make use of the new
flags and deal with higher [V]HT bandwidths.
ieee80211_add_channel() specifically did not take flags so it will
not support naything beyond 20Mhz channels.
Note: I am not entirely happy with the "cbw_flag[s]" name, but we
do use chan_flags elsewhere already.
MFC after: 2 weeks
Reviewed by: adrian, gnn
Sponsored by: Rubicon Communications, LLC (d/b/a "Netgate")
Differential revision: https://reviews.freebsd.org/D26091
The standard uses 80+80 and 80p80 but nowhere 80_80.
Switch the latter to 80P80 for all the macros and comments refering
to #defined flags which I could find.
The only place we leave as 80p80 is the ifconfig command line arguments
as we spell them all in lower case.
Ideally we would use 80+80 for any interactions with the user and
80P80 for anything internal but let us not confuse parsers and
hence avoid the '+' in either case.
Reviewed by: adrian, gnn
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC (d/b/a "Netgate")
Differential Revision: https://reviews.freebsd.org/D26001
Rather then using magic numbers duplicate IEEE80211_FVHT_VHT* in
ifconfig (cleanup of these and other flags used and not exposed by
net80211 should happen later) and use those.
In the kernel this simplifies one ioctl path (the other one currently
relies on individual bit flags being passed in).
We also re-order the 80P80 and 160 flag for 160 to come before 80+80
and more clearly leave the flags as TODO in one of the 160/80+80 cases.
Reviewed by: adrian
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC (d/b/a "Netgate")
Differential Revision: https://reviews.freebsd.org/D26000
The later firmware devices (including iwn!) support multiple configuration
contexts for a lot of things, leaving it up to the firmware to decide
which channel and vap is active. This allows for things like off-channel
p2p sta/ap operation and other weird things.
However, net80211 is still focused on a "net80211 drives all" when it comes to driving
the NIC, and as part of this history a lot of these options are global and not per-VAP.
This is fine when net80211 drives things and all VAPs share a single channel - these
parameters importantly really reflect the state of the channel! - but it will increasingly
be not fine when we start supporting more weird configurations and more recent NICs.
Yeah, recent like iwn/iwm.
Anyway - so, migrate all of the HT protection, legacy protection and preamble
stuff to be per-VAP. The global flags are still there; they're now calculated
in a deferred taskqueue that mirrors the old behaviour. Firmware based drivers
which have per-VAP configuration of these parameters can now just listen to the
per-VAP options.
What do I mean by per-channel? Well, the above configuration parameters really
are about interoperation with other devices on the same channel. Eg, HT protection
mode will flip to legacy/mixed if it hears ANY BSS that supports non-HT stations or
indicates it has non-HT stations associated. So, these flags really should be
per-channel rather than per-VAP, and then for things like "do i need short preamble
or long preamble?" turn into a "do I need it for this current operating channel".
Then any VAP using it can query the channel that it's on, reflecting the real
required state.
This patch does none of the above paragraph just yet.
I'm also cheating a bit - I'm currently not using separate taskqueues for
the beacon updates and the per-VAP configuration updates. I can always further
split it later if I need to but I didn't think it was SUPER important here.
So:
* Create vap taskqueue entries for ERP/protection, HT protection and short/long
preamble;
* Migrate the HT station count, short/long slot station count, etc - into per-VAP
variables rather than global;
* Fix a bug with my WME work from a while ago which made it per-VAP - do the WME
beacon update /after/ the WME update taskqueue runs, not before;
* Any time the HT protmode configuration changes or the ERP protection mode
config changes - schedule the task, which will call the driver without the
net80211 lock held and all correctly serialised;
* Use the global flags for beacon IEs and VAP flags for probe responses and
other IE situations.
The primary consumer of this is ath10k. iwn could use it when sending RXON,
but we don't support IBSS or AP modes on it yet, and I'm not yet sure whether
it's required in STA mode (ie whether the firmware parses beacons to change
protection mode or whether we need to.)
Tested:
* AR9280, STA/AP
* AR9380, DWDS STA+STA/AP
* ath10k work, STA/AP
* Intel 6235, STA
* Various rtwn / run NICs, DWDS STA and STA configurations
U-APSD (unscheduled automatic power save delivery) is a power save method
that's a bit better than legacy PS-POLL - stations can mark frames with
an extra flag that tells the AP to leak out more frames after it sends
its own frames rather than needing to send a PS-POLL to get another frame
from the AP.
Now, this code just handles the negotiation bits; it doesn't actually
implement U-APSD. That's up to drivers, and nothing in the tree yet
implements this. I /may/ implement this for ath(4) if I eventually care
enough but right now I plan on just implementing it for firmware offload
based NICs that handle this in the NIC.
I'll commit the ifconfig bit after this and I may have some follow-up
commits as this gets used more by me in local testing.
This should be a glorious no-op for everyone else. If things change
for anyone that isn't fixed by a complete recompile then please reach out
to me.
This is a new, optional (for now!) method that drivers can use to separate
node allocation and node initialisation. Right now they're the same, and
drivers that need to do node allocation via firmware commands need to sleep
and thus they need to defer node allocation into an internal taskqueue.
Right now they're just separate but not deferred. Later on if I get the time
we'll start deferring the node and key related operations but that requires
making a bunch of other stuff (notably things that generate frames!) also
async/deferred.
Tested:
* RT3593, STA/DWDS mode
* AR9380, STA/AP modes
* QCA9880 (athp) - STA/AP modes
Allow net80211 drivers to register a small vtable of debugnet-related
methods.
This is not a functional change. Driver support is needed, similar to
debugnet(4) for wired NICs.
Reviewed by: adrian, markj (earlier version both)
Differential Revision: https://reviews.freebsd.org/D17308
The 11b/11g ERP and slot time update handling are two things which weren't
migrated into the per-VAP state when Sam did the initial VAP work.
That makes sense for a lot of setups where net80211 is driving radio state
and the radio only cares about the shared state.
However, as noted by a now deleted comment, the ERP and slot time updates
aren't EXACTLY correct/accurate - they only take into account the most
RECENTLY created VAP, and the state updates when one creates/destroys
VAPs isn't exactly great.
So:
* track the short slot logic per VAP;
* whenever the slot time configuration changes, just push it into a deferred
task queue update so drivers don't have to serialise it themselves;
* if a driver registers a per-VAP slot time handler then it'll just get the
per VAP one;
* .. if a driver registers a global one then the legacy behaviour is maintained -
a single slot time is calculated and pushed out.
Note that the calculated slot time is better than the existing logic - if ANY
of the VAPs require long slot then it's disabled for all VAPs rather than
whatever the last configured VAP did.
Now, this isn't entirely complete - the rest of ERP tracking around short/long
slot capable station tracking needs to be converted into per-VAP, as well
as the preamble/barker flags. Luckily those also can be done in a similar
fashion - keep per-VAP counters/flags and unify them before doing the driver
update. I'll defer that work until later.
All the existing drivers can keep doing what they're doing with the global
slot time flags as that is maintained. One driver (iwi) used the per-VAP
flags instead of the ic flags, so now that driver will work properly.
This unblocks some ath10k porting work as the firmware takes the slot time
configuration per-VAP rather than globally, and some firmware handles
STA+AP and STA+STA (on same/different channels) configurations where
the firmware will switch slot time as appropriate.
Tested:
* AR9380, STA/AP mode
* AR9880 (ath10k), STA mode
Wrap ieee80211_add_channel_list_2ghz into another function
which supplies default (1-14) channel list to it and drop
its copies from drivers.
Checked with RTL8188EE, country US / JP / KR / UA.
MFC after: 2 weeks
Since r287197 ieee80211com is a part of drivers softc; as a result,
after detach all pointers to it (iv_ic, ni_ic) are invalid. Most
possible users (tasks, interrupt handlers) are blocked / removed
when device is stopped; however, ioctl handlers were not tracked
and may crash if ieee80211com structure is accessed.
Since ieee80211com pointer access from ieee80211vap structure is not
protected by lock (constant after interface creation) and used in
many other places just use reference counting for ioctl handlers;
on detach set 'detached' flag and wait until reference counter goes to 0.
For HEAD ieee80211vap size was changed (__FreeBSD_version bumped);
however, in stable branches I'm going to split / reuse the last
iv_spare field for KBI stability.
Tested with:
- rsu(4), SIOCSIFCAP (-rxcsum) ioctl;
- rtwn_pci(4), SIOCG80211 / IEEE80211_IOC_HTPROTMODE ioctl.
MFC after: 1 week
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
As part of (eventual) p2p/tdls/multi-STA support, a lot of global configuration
parameters (WME, ERP (slot, preamble), channel width, HT protmode, etc are the
biggest offenders) should be per-VAP.
For multi-BSS VAP operation they may be linked, but for p2p/TDLS
operation that can be off-channel they can definitely be different
(think: 2GHz STA, 5GHz p2p.)
The global configuration view of these is mostly a "configure the current
non-smart-firmware NIC" view. This should be split up into per-VAP state,
then a global non-smart-firmware-NIC management layer to handle channel
changes and such in software.
This is step one in a loooong road for this. It should be a big non-functional
change for everyone.
* create a per-VAP WME update call.
* call it if its set, and call the global callback if it isn't
This still uses global WME state - it's just preparation for a future change
which will make the WME state per-VAP and fall through to a shared WME
configuration for hostap operation.
Note: this requires a full kernel recompile; the internal net80211 ABI has changed.
Reviewed by: avos
Differential Revision: https://reviews.freebsd.org/D9986
ucast/mcast/mgmt HT rate.
- Init global ieee80211_htrateset only once; neither ic_htcaps nor
ic_txstream is changed when device is attached;
- Move global ieee80211_htrateset structure to ieee80211com;
there was a possible data race when more than 1 wireless device is
used simultaneously;
- Discard unsupported rates in ieee80211_ioctl_settxparams(); otherwise,
an unsupported value may break connectivity (actually,
'ifconfig wlan0 ucastrate 8' for RTL8188EU results in immediate
disconnect + infinite 'device timeout's after it).
Tested with:
- Intel 6205, STA mode.
- RTL8821AU, STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9871
* on the station side, only call the quiet time IE method if we have a
quiet IE - otherwise call the NULL method once, and then don't waste
time calling NULL
* on the beacon generation side - force a beacon regeneration each time
quiet time is enabled/disabled. Without this, enabling/disabling quiet
time IE would cause the beacon contents to be corrupted since none of
the "move contents around" logic (like for CSA and TIM handling) is implemented.
This changes the size of ieee80211_node so it requires a kernel recompile,
but no userland recompile.
Tested:
* AR9380, AP mode, enabling/disabling quiet time IE
* AR9380, STA mode, with upcoming driver changes.
Flags
- IEEE80211_F_ASCAN
- IEEE80211_F_SIBSS
- IEEE80211_F_IBSSON
are not used since r170530 (old WI compatibility ioctls removal)
and r178354 (removed from other places).
IEEE80211_F_TXPOW_FIXED was never utilized; initially added with
IEEE80211_F_TXPOW_AUTO / IEEE80211_F_TXPOW_OFF flags,
which were replaced with IEEE80211_C_TXPMGT capability check in r138568.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9369
* allocate an ext bit for fragment offload. Some NICs (like the ath10k
hardware in native wifi or 802.3 mode) support doing packet fragmentation
in firmware/hardware, so we don't have to do it here.
* allocate an ext bit for VHT and start using it.
I added IEEE80211_TX_LOCK() a few years ago because there were races between
seqno allocation, driver queuing and crypto IV allocation. This meant that
they'd appear out of sequence and the receiver would drop them, leading to
terrible performance or flat out traffic hangs.
This flag should be set by drivers that do their own sequence number
allocation for all frames it needs to happen for, including beacon frames.
Eventually this should lead to the driver taking care of locking for
allocating seqno and other traffic-triggered events (eg addba setup.)
The 11n code uses these bits for both configuration /and/ controlling
the channel width on softmac chips - it uses it to find the widest
width for all VAPs (eg a HT20 vap and a HT40 vap) to know what to
configure the ic_curchan.
For fullmac devices it isn't /as/ important, as each virtual device
exposed by the firmware will likely have its own configuration and the
firmware figures out what to do to enable it.
* rename the ieee80211com field for vht mcsinfo to be ic_, not iv;
* add a vht config field, stealing from the spares I left there.
This doesn't change the ABI.
The ath10k firmware supports hardware WEP offload, and in native wifi mode
(or 802.3 ethernet mode, for that matter) the WEP key isn't actually included
in the TX payload from net80211. Instead, a separate firmware command is issued
that sets the default TX key to be the specified key.
However, net80211 doesn't at all inform the driver layer that this is
occuring - it just "expects" to be inserting WEP header information
when doing WEP TX, even with hardware encryption.
So, to better support the newer world order, turn the default TX key assignment
into a VAP method that can be overridden by the driver and ensure its wrapped
in a crypto begin/end set. That way it should be correctly atomic from the
point of view of keychanges (as long as the driver does the right thing.)
It'd be nice if we passed through to the key_set call a flag that says
"also make this the default key" - that's captured here by calling the
deftxkey method after the key_set method. Maybe I can do that later.
Note: this is a net80211 ABI change, and will require a kernel+modules
recompile. Happy Holidays, etc.
Tested:
* ath10k driver port
* rtwn_usb, WEP station
This is a work in progress and some of this stuff may change;
but hopefully I'm laying down enough stuff and space in fields
to allow it to grow without another major recompile.
We'll see!
* Add a net80211 PHY type for VHT 2G and VHT 5G.
Note - yes, VHT is supposed to be for 5GHZ, however some vendors
(*cough* most of them) support some subset of VHT rate support
in 2GHz. No - not 80MHz wide channels, but at least some MCS8-9
support, maybe some beamforming, and maybe some longer A-MPDU
aggregates. I don't want to even think about MU-MIMO on 2GHz.
* Add an ifmedia placeholder type for VHT rates.
* Add channel flags for VHT, VHT20/40U/40D/80/80+80/160
* Add channel macros for the above
* Add ieee80211_channel fields for the VHT information and flags,
along with some padding (so this struct definitely grows.)
* Add a phy type flag for VHT - 'v'
* Bump the number of channels to a much higher amount - until we get
something like the linux mac80211 chanctx abstraction (where the
stack provides a current channel configuration via callbacks,
versus the driver ever checking ic->ic_curchan or similar) we'll
have to populate VHT+HT combinations.
Eg, there'll likely be a full set of duplicate VHT20/40 channels to match
HT channels. There will also be a full set of duplicate VHT80 channels -
note that for VHT80, its assumed you're doing VHT40 as a base, so we
don't need a duplicate of VHT80 + 20MHz only primary channels, only
a duplicate of all the VHT40 combinations.
I don't want to think about VHT80+80 or VHT160 for now - and I won't,
as the current device I'm doing 11ac bringup on (QCA9880) only does
VHT80.
I'll likely revisit the channel configuration and scanning related
stuff after I get VHT20/40 up.
* Add vht flags and the basic MCS rate setup to ieee80211com, ieee80211vap
and ieee80211_node in preparation for 11ac configuration.
There is zero code that uses this right now.
* Whilst here, add some more placeholders in case I need to extend
out things by some uint32_t flag sized fields. Hopefully I won't!
What I haven't yet done:
* any of the code that uses this
* any of the beamforming related fields
* any of the MU-MIMO fields required for STA/AP operation
* any of the IE fields in beacon frame / probe request/response handling
and the calculations required for shifting beacon contents around
when the TIM grows/shrinks
This will require a full rebuild of net80211 related programs -
ifconfig, hostapd, wpa_supplicant.
* ic_freq is the centre of the primary channel, not the centre of the
HT40/HT80/etc channel. Add a method to access that.
* Add a method to access the centre of the primary channel, including
knowing the centre of the 5/10/20/40/80, versus the primary channel.
Ie, it's the centre of the 40, 80, 160MHz channel.
* Add a method to access the centre frequency of the secondary 80MHz
channel - we don't support VHT yet, but when we do.
* Add methods to access the current channel and the per-dev desired
channel. Ideally drivers that do full offload with a per-vap channel
configuration should use the vap channel, NOT ic_curchan.
Non-offload drivers that require net80211 to change the channel should
be accessing ic_curchan.
This is a very simple addition to the net80211 scan support.
It doesn't implement a replacement scan interface - it just disables
the pieces that we should disable to make this lifecycle a bit
more managable.
There's more work to come before full scan offload support is available
but it should be good enough for driver work.
* add a flag to say "full offload"
* don't do probe requests when scanning full-offload - firmware can do that
* don't do powersave transitions and buffering - firmware can do that
tested:
* iwm(4) - STA mode
* ath10k port (local, not in freebsd-head yet)
Reviewed by: avos
Differential Revision: https://reviews.freebsd.org/D8262
Add new lock for stageq (part of ieee80211_superg structure) and
ni_tx_superg (part of ieee80211_node structure);
drop com_lock protection where it is used to protect them.
While here, drop duplicate OPACKETS counter incrementation.
ni_tx_ampdu is not protected with it (however, it is also used without
locking in other places; probably, it requires some other solution
to be thread-safe).
Tested with RTL8188CUS (AP) and RTL8188EU (STA).
NOTE: Since this change breaks KBI, all wireless drivers need to be
recompiled.
Reviewed by: adrian
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D6958
Replace ifnet list lookup (which is broken since r287197, because
IFT_IEEE80211 type is not used anymore) with iteration on
ieee80211com list.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6419
This change adds few methods for net80211 channel table setup:
- ieee80211_add_channel()
- ieee80211_add_channel_ht40()
(primarily for drivers, that parse EEPROM to get channel list -
they will allow to hide implementation details).
- ieee80211_add_channel_list_2ghz()
- ieee80211_add_channel_list_5ghz()
(mostly as a replacement for ieee80211_init_channels() - they will allow
to specify non-default channel list; may be used in ic_getradiocaps()).
Tested with wpi(4) (add_channel) and rum(4) (add_channel_list_2ghz).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6124
do software A-MSDU encapsulation.
Right now there's AMSDU TX/RX capability bits and they're mostly
unused, however I'd like to maintain those as the general configuration,
not also "please software encap AMSDU." For platforms that can do
A-MSDU in firmware (iwn, iwm, etc) then their init paths can read
this flag to configure A-MSDU.
For hz=1000 any number, greater than 4194 causes integer overflow;
this change casts the number to uint64_t before operating with it.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5268
we're assuming hz=1000 and not gracefully handling when it isn't.
The math involved will return 0 for hz < 1000, which it is on some
platforms and on DragonflyBSD.
This doesn't fix it, it:
* converts one manual use over to use the macro, and
* comments where it needs some thought/fixing.
I'll think about this a bit more before fixing it.
Submitted by: imre@vdsz.com
This call may be used when device cannot continue to operate normally
(e.g., throws firmware error, watchdog timer expires)
and need to be restarted.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3998
The MAC can be fetched from the key struct.
I added the ndis updates to make it compile.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3657
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix