Including arm/mv/gpio.c now depends on 'gpio' device. 'device gpio' was
added to all kernconf files of Marvell boards, except ARMADAXP (dummy
mv_gpio_res definition was removed) and ARMADA38X (not supported yet).
This commit allows to use generic files.mv on A38X.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4372
This commit introduces support for etherswitch devices that utilize SMI as
a way of accessing its registers. SMI register is located in address space
of mge -- access to it was exported through MDIO interface.
Attachment functions were enhanced so as to ensure proper initialisation
in both cases: 1) PHYs attached directly to mge, 2) PHYs attached to
switch device and switch attached to mge. Attachment of etherswitch device
depends on dts entry with compatible="mrvl,sw" property. If none is found,
typical PHY attachment procedure follows.
In case of switch attached, PHYs' status and configuration is accessible
via etherswitchcfg, and ifconfig shows always-up, non-configurable mge
interfaces.
Due to the fact that there may be simultaneous accessess to SMI
registers (e.g. from PHY attached to one of mge instances and switch
to the other), SMI access interlock was added. It is SX lock,
because sleep ability is necessary -- busy-waiting would result
in poor performance due to long delays required by hardware.
Underlying switch driver is obliged to use sleepable locks as well.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3900
each of the existing kernel configs. This gives a place to put config
that applies to the entire arch.
Add the ARM_NEW_PMAP option to std.armv6. This is working well in early
testing and it's time for wide exposure, but it's still nice to be able
to fall back to the old implementation for testing when a problem comes
along. Eventually the option and the old implementation will go away.
The opportunity now exists to move a whole lot of boilerplate from all the
arm kernel config files into std.arm*, but that's a commit for another day.
in effect due to r250753. That is sufficient for all SoCs with a 32 byte
cache line size. Systems with 64 byte cache lines will need the option;
that will be done in a separate commit.
Thanks to loos@ for pointing out r250753.
this to the cache line size is required to avoid data corruption on armv4
and armv5, and improves performance on armv6, in both cases by avoiding
partial cacheline flushes for USB IO.
All these configs already exist in 10-stable. A few that don't (and
thus can't be MFC'd yet) will be committed separately.
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
so that we don't need an empty implementation of it for every Marvell platform
that has no PCI. This allows the removal of the SheevaPlug-specific stub and
config files, and eliminates the need to add similar stubs for future models.
Marvell platforms that do expose PCI are compiled with 'device pci' which
causes the real (non-weak) implementation in dev/fdt/fdt_pci.c to be used.
Approved by: cognet (mentor)
such that when commenting/uncommentting lines, horizontal spacing is
maintained...
Also fix some minor comment formatting to line things up, etc...
Reviewed by: gnn, imp
MFC after: 1 week
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
NFSCL, NFSD instead of NFSCLIENT, NFSSERVER since
NFSCL and NFSD are now the defaults. The client change is
needed for diskless configurations, so that the root
mount works for fstype nfs.
Reported by seanbru at yahoo-inc.com for i386/XEN.
Approved by: re (hrs)
The following systems are involved:
- DB-88F5182
- DB-88F5281
- DB-88F6281
- DB-78100
- SheevaPlug
This overhaul covers the following major changes:
- All integrated peripherals drivers for Marvell ARM SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- Since the common FDT infrastrucutre (fdtbus, simplebus) is used we say
good by to obio / mbus drivers and numerous hard-coded config data.
Note that world needs to be built WITH_FDT for the affected platforms.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation.
- The device is based on Marvell 88F6281 system on chip.
- More info about the platform at http://www.plugcomputer.org
- To build the FreeBSD kernel:
make buildkernel TARGET_ARCH=arm KERNCONF=SHEEVAPLUG
- Installation notes at: http://wiki.freebsd.org/FreeBSDMarvell
Submitted by: Michal Hajduk
Obtained from: Semihalf
