s/1518/ETHER_MAX_LEN
Some style changes, add some braces, mostly residual from having
a lot of debug hooks added while working on this driver.
Bring in a plethora of changes from NetBSD:
revision 1.58
date: 2001/03/08 11:07:08; author: ichiro; state: Exp; lines: +17 -1
it wait until busy flag disappears.
it was able to prevent some cards with late initializing faling in wi_reset().
revision 1.41
date: 2000/10/13 19:15:08; author: jonathan; state: Exp; lines: +4 -2
Fix wi_intr() to avoid touching card registers during insert/remove events,
when sharing an interrupt with other devices:
check sc->sc_enabled, and drop the interrupt if its' off.
revision 1.30
date: 2000/08/18 04:11:48; author: jhawk; state: Exp; lines: +4 -4
Copy wi_{dst,src}_addr from struct wi_frame into faked-up ether_header
instead of addr1 and addr2. THis means that tcpdump -e will show the
correct MAC address for communications with access points instead of showing
the BSSID.
In the future there should be 802.11 support for bpf/libpcap/tcpdump,
but that is aways down the road.
Parag Patel did all of the grunt work, so he gets the credit.
Register definitions and actions inferred from a Linux driver,
so Intel also gets some 'credit'.
o Change the number of init tries from 5 to a #define.
o Allow up to 5s rather than 2s for commands to complete. This
is still much less than 51 minutes, but makes my intel card init
with more reliability than before.
possible for some systems where the device is there, but the BIOS
hasn't allocated memory resources for it), we don't panic.
Submitted by: Gerard Roudier
Don't leak iospace when irq allocation fails. (call wi_free())
Call bus_release_resource() with the correct "rid" obtained from
bus_alloc_resource() that's saved in the softc instead of a hardcoded
0.
immediate value or the accumulator. 0 is the chip's internal
representation for the accumulator, and so 0 is an invalid immediate value
when the accumulator can also be specified as an argument.
Submitted by: gibbs
overflow the request queue. The reason we want to do this is that we
now push out completed CTIOs as we complete them- this gets the QLogic
working on them quicker. So we need to know whether we can put the entire
burrito out before we start.
We now support conjoint status with data for the last CTIO for both Fibre
Channel and SCSI. Leave the old code in place in case we need to go back
(minor 3 line ifdef).
Ultra-ultra important- *don't* set rq->req_seg_count for non-data
target mode requests in isp_pci_dmasetup. D'oh- this is actually
the tag value area for a CTIO. What *was* I thinking? Boy howdy
does both aic7xxx and sym get awfully unhappy when on reconnect
you give them a constant '1' for a tag value.
function- we did it a bit cleaner. We only use this if a CTIO completes with
!CT_OK state. We now have managed to get away without having to poke around
and trying to find the original ATIO- the csio we're using has the tag_id
and lun values with it which is mostly what we need when we do the putback.
Make sure we correctly propagate AT_TQAE->CT_TQAE for tags. Make sure
we call ISP_DMAFREE only if we had DATA to move.
tag is active for an ATIO, and say that you want to reconnect with
a tag value in a CTIO have *never* been exercised until now. This lossage
derived from Solaris code where this stuff originally came from that is
about 7 years old. Amazing.
We now bundle the incoming tag (legal values are 0..256) as the low
16 bits of the ccb_accept_tio's at_tagid while we put the firmware
handle for this ATIO in the top 16 bits- define some macros to make
this cleaner.
Complete some Ansification.
Redo establishment of default SCSI parameters whether or not
we've been compiled for target mode. Unfortunately, the Qlogic
f/w is confused so that if we set all targets to be 'safe' (i.e.,
narrow/async), it will also then report narrow, async if we're
contacted in target mode from that target (acting in initiator
role). D'oh!
Fix ISPCTL_TOGGLE_TMODE to correctly enable the right channel for
dual channel cards. Add some more opcodes. Fix a stupid NULL
pointer bug.
Simplify initialization and remove offending DMA channel resets there.
The resets trash whatever is pointed to DMA registers, but at cmi_attach()
time the DMA registers have not been initialized with valid addresses.
Reviewed by: Cameron Grant <gandalf@vilnya.demon.co.uk>
It appears that some of the new PRISM2 cards need it.
Fail the probe if we fail to read the MAC address.
Fix a comment.
Delete the unload printf. The bus system now prints this message.
