channel has been disabled by BIOS. This prevents a bus timeout
machine check on B&W G3 PowerMacs, which have a primary-only CMD646
on the motherboard.
Approved by: sos
Obtained from: NetBSD
succeeds. There is a difference between how OLDCARD and NEWCARD deal
with their resources, and this code exposes that difference. I'm not
sure which behavior is correct, and will need to look into that in
more detail. However, it appears that we go ahead and allocate the
right thing in both cases that I have access to (CF cards, CDROM, and
external ata enclosures), so go ahead and ignore the failure to get
the resource for the other rid. There's already another check to make
sure that the actual allocation works correctly, and that should be
sufficient to catch cases that don't work.
Submitted by: wpaul and iedowse
o add back rx monitor support
o make WI_RID_SCAN_RES DTRT
o fix a bug handling zero-length RID requests (used by dstumbler to set
a zero-length SSID)
o make RID_SCAN_REQ DTRT
o add back WI_RID_OWN_SSID
o fix wi_scan_ap to take a channel mask and txrate (for prism cards)
These changes fix dstumbler -o (monitor mode). A minor change to dstumbler
is needed to get normal AP scanning mode to work right; this is preferred to
modifying the driver.
PR: kern/53187
Reviewed by: Bruce M Simpson <bms@spc.org>
flag'ed INTR_MPSAFE. In ep_if_start(), use the IF_DEQUEUE macro to
grab the next mbuf to send, and use IF_PREPEND if the card is busy
and we actually can't handle it right now.
The old code was first getting the mbuf by taking it from the queue
without using the macros, thus without locking, and without removing
it from the queue either. It was later assuming that IF_DEQUEUE would
give him this same mbuf.
Tested by: mich
when the user specifies a maximum fragment size < 2.
This is the behavior that Linux provides and fixes the problem I've
observed in Tribes2 where sounds effects are delayed by 1/2 a second.
so can leave stale data in the buffer and confuse the driver.
- enable the ability to set the 'disable' hint for the driver to keep it
from attaching. i.e. 'hw.ips.0.disable=1' will prevent the driver from
attaching.
- Only detach if attach suceeded.
Submitted by: mjacob
in the netisr case. This would result in a lock reversal. This
fixes the net.isr.enable=1 case. Better performance might be
obtained by chaining all packets received, dropping the lock, and
then calling if_input() on each one.
Reported by: hmp
of the contents of the CCSCBCTL register into our
local varaible. The other bits are used in later tests.
This avoids a potential deadlock in ahd_run_qoutfifo()
if we happen to catch the DMA engine in just the right
state.
read permision only required for listing, read/write required for
read/write to registers
fix a possible memory leak
clean up error handling a bit
Reviewed by: silence
Reorder how the pci probing in handled. before adding devices, check to
see if the slot is a multi-function device to see if we should probe all
the functions.
Original idea by: imp
drivers that implemnt the i2c bit banging bus interface not have to
recompile iicbb in order to add an attachment for it.
This will mean the bktr and other definitions can go back to their
respective drivers.
- Mark that it cannot handle greater than 4GB of RAM at this time. Fixing
that will come later. Fail any attempts to dump above thati limit.
- If a call to aac_disk_dump() needs to be split into multiple i/o's,
increment the virtual offset after each i/o instead of just dumping the
same offset over and over again.
- Bail out if bus_dmamap_load() returns an error. Error recovery is likely
not possible.
This version of the driver code is compatible with near-release FreeBSD 5.1
kernel/driver interfaces.
modules/Makefile, man page and other bindings to follow shortly, once I get
this part of the check-in right.
Approved by: markm(mentor)
Previously, any normal I/O on an fdc(4) device would fail with ENXIO
if the device had been opened in non-blocking mode and then closed
prior to the conventional access; that would last until the floppy
disk was ejected and re-inserted to raise the unit attention condition.
Add a clarifying comment.
populated. Apparently, if you use an ehci controller, it's not.
Use usbd_device2interface_handle() to retrieve the interface handle.
NOTE: uaa->iface is populated in the probe routine, so I suspect the
fact that it's NULL in the attach routine is a bug in the ehci driver.
Also, don't depend on the PHY addresses returned by the AXE_CMD_READ_PHYID
command. The address is correct for my LinkSys NIC, but a user has
reported that with a D-Link NIC, the PHYID command returns address 4
while the attached Broadcom PHY is in fact strapped for address 0.
Instead, latch onto the first PHY address that returns valid data
during a readreg operation.
