Disable building tickadj(8) by removing util from SUBDIR in the xntpd
Makefile. Note that the sources are still there and tickadj can still
be built and installed by doing:
# cd /usr/src/usr.sbin/xntpd/util
# make all install
There are enough references to tickadj in e.g. the xntpd documentation
(not to mention the sysctl variables it uses etc.) that I don't feel
up to implementing the final solution right now.
Kinda-approved-by: phk
rwho iff /var/rwho is empty. Call `uptime' instead. This doesn't
belong under `network' right away, but at least reports the same
informaton about the local system. rwhod is not turned on by default
(for good reason), and i've already seen too many of the above
messages...
original contents of the file preserved as examples for administrators
that need to enable them.
Also add a comment to the examples pointing out that the authentication
functionality is largely unused and requires rebuilding libutil.
Reviewed by: jkh
file formats. I have added a new rc.conf variable ${ldconfig_paths_aout}
which is like ${ldconfig_paths}, but only for a.out shared libraries.
On a "standard" ELF system, the ELF ldconfig path is taken from
${ldconfig_paths}, while the a.out ldconfig path is taken from
${ldconfig_paths_aout}.
On a not-yet-converted a.out system, only the a.out ldconfig path
is set, and it is taken from ${ldconfig_paths_aout}. If that
variable is unset, /etc/rc defaults it to the value of ${ldconfig_paths},
on the assumption that the system's "/etc/rc.conf" file hasn't been
updated.
committed a fix for in 2 days and 3 different people have forgotten
to update this file. GRRR! What's it going to take, electrodes to
the sensitive bits, people?? :-)
===================================
HARP | Host ATM Research Platform
===================================
HARP 3
What is this stuff?
-------------------
The Advanced Networking Group (ANG) at the Minnesota Supercomputer Center,
Inc. (MSCI), as part of its work on the MAGIC Gigabit Testbed, developed
the Host ATM Research Platform (HARP) software, which allows IP hosts to
communicate over ATM networks using standard protocols. It is intended to
be a high-quality platform for IP/ATM research.
HARP provides a way for IP hosts to connect to ATM networks. It supports
standard methods of communication using IP over ATM. A host's standard IP
software sends and receives datagrams via a HARP ATM interface. HARP provides
functionality similar to (and typically replaces) vendor-provided ATM device
driver software.
HARP includes full source code, making it possible for researchers to
experiment with different approaches to running IP over ATM. HARP is
self-contained; it requires no other licenses or commercial software packages.
HARP implements support for the IETF Classical IP model for using IP over ATM
networks, including:
o IETF ATMARP address resolution client
o IETF ATMARP address resolution server
o IETF SCSP/ATMARP server
o UNI 3.1 and 3.0 signalling protocols
o Fore Systems's SPANS signalling protocol
What's supported
----------------
The following are supported by HARP 3:
o ATM Host Interfaces
- FORE Systems, Inc. SBA-200 and SBA-200E ATM SBus Adapters
- FORE Systems, Inc. PCA-200E ATM PCI Adapters
- Efficient Networks, Inc. ENI-155p ATM PCI Adapters
o ATM Signalling Protocols
- The ATM Forum UNI 3.1 signalling protocol
- The ATM Forum UNI 3.0 signalling protocol
- The ATM Forum ILMI address registration
- FORE Systems's proprietary SPANS signalling protocol
- Permanent Virtual Channels (PVCs)
o IETF "Classical IP and ARP over ATM" model
- RFC 1483, "Multiprotocol Encapsulation over ATM Adaptation Layer 5"
- RFC 1577, "Classical IP and ARP over ATM"
- RFC 1626, "Default IP MTU for use over ATM AAL5"
- RFC 1755, "ATM Signaling Support for IP over ATM"
- RFC 2225, "Classical IP and ARP over ATM"
- RFC 2334, "Server Cache Synchronization Protocol (SCSP)"
- Internet Draft draft-ietf-ion-scsp-atmarp-00.txt,
"A Distributed ATMARP Service Using SCSP"
o ATM Sockets interface
- The file atm-sockets.txt contains further information
What's not supported
--------------------
The following major features of the above list are not currently supported:
o UNI point-to-multipoint support
o Driver support for Traffic Control/Quality of Service
o SPANS multicast and MPP support
o SPANS signalling using Efficient adapters
This software was developed under the sponsorship of the Defense Advanced
Research Projects Agency (DARPA).
Reviewed (lightly) by: phk
Submitted by: Network Computing Services, Inc.
addresses by default.
Add a knob "icmp_bmcastecho" to "rc.network" to allow this
behaviour to be controlled from "rc.conf".
Document the controlling sysctl variable "net.inet.icmp.bmcastecho"
in sysctl(3).
Reviewed by: dg, jkh
Reminded on -hackers by: Steinar Haug <sthaug@nethelp.no>
