- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
long as I remember, and completely superseded by better maintained umass(4).
It's main idea was to optionally avoid CAM dependency for such devices, but
with move ATA to CAM, it is not actual any more.
No objections: hselasky@, thompsa@, arch@
- Remove most of direct relations between ATA(4) peripherial and controller
levels. It makes logic more transparent and is a mandatory step to wrap
ATA(4) controller level into ATA-native CAM SIM.
- Tune AHCI and SATA2 SiI drivers memory allocation a bit to allow bigger
I/O transaction sizes without additional cost.
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
requesting IDENTIFY from slave device first. This order is important
for proper cable type detection by master device.
PR: kern/136438
Approved by: re (kib)
and partially r188903. Revert breaks new drives detection on reinit to the
state as it was before me, but fixes series of new bugs reported by some
people.
Unconditional queueing of ata_completed() calls can lead to deadlock if
due to timeout ata_reinit() was called at the same thread by previous
ata_completed(). Calling of ata_identify() on ata_reinit() in current
implementation opens numerous races and deadlocks.
Problems I was touching here are still exist and should be addresed, but
probably in different way.
drivers' probe routines. It allows not to sleep and so not drop Giant inside
ata_identify() critical section and so avoid crash if it reentered on
request timeout. Reentering of probe call checked inside of it.
Give device own knowledge about it's type (ata/atapi/atapicam). It is not
a good idea to ask channel status for device type inside ata_getparam().
Add softc memory deallocation on device destruction.
kernel dumping case.
ata_completed() may initiate ata_reinit() on error, that may lead to drives
attach or detach. Attach and detach are sending requests to drives and sleep
waiting for results. But ata_finish() can be called directly from
interrupt handler where sleeping is prohibited, so we must break this chain
somewhere. This place seems to fit best.
- protect againtst recursions,
- add new devices detection using ata_identify().
Improve ata_identify():
- do not add duplicate device if device already exist.
Rework SATA hot-plug events handling. Instead of unsafe duplicate
implementation use common ata_reinit() to handle all state changes.
All together this gives quite stable and robust cold- and hot-plug operation,
invariant to false, lost and duplicate events.
ata_detach() to implement IOCATAATTACH/IOCATADETACH ioctls.
This will permit channel drivers to properly shutdown port hardware on channel
detach and init it on attach.
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.
However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:
atacore: ATA core functionality, always needed for any ATA setup
atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.
ataahci: AHCI support, also pulled in by some vendor modules.
ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets
atadisk: ATA disk driver
ataraid: ATA softraid driver
atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver
atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge
This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:
device atacore
device atapci
device atavia
And then you need the atadisk, atapicd etc lines in there just as usual.
If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
This can be used to disable the 80pin cable check on systems which forget to
set the bit -- such as certain laptops and Soekris boards.
PR: kern/114605 (somewhat reworked)
Submitted by: marck
MFC after: 1 week
So if we have channel 0..3 devclass_get_maxunit is 4.
It's never been a problem as devclass_get_device() has
catched a possibly bad input.
Discussed with: scottl
This avoids calling busdma in the request processing path which caused a traumatic performance degradation.
Allocation has be postponed to after we know how many devices we possible can have on portmulitpliers to save some space.
The problem is that the PM support is part of a much larger WIP here, but due to popular demand I decided to get some of it imported.
Also I forgot the mention:
HW sponsored by: Vitsch Electronics / VEHosting
Support is working on the Silicon Image SiI3124/3132.
Support is working on some AHCI chips but far from all.
Remember this is WIP, so test reports and (constructive) suggestions are welcome!
for a configurable number of seconds, spin the disk down. Spin it back
up on the next request.
Notice that the timeout is only armed by a request, so to spin down a
disk you may have to do:
atacontrol spindown ad10 5
dd if=/dev/ad10 of=/dev/null count=1
To disable spindown, set timeout to zero:
atacontrol spindown ad10 0
In order to debug any trouble caused, this code is somewhat noisy on the
console.
Enabling spindown on a disk containing / or /var/log/messages is not
going to do anything sensible.
Spinning a disk up and down all the time will wear it out, use sensibly.
Approved by: sos
triggers a KASSERT) or local variables. In the case of kern_ndis, the
tsleep() actually used a common sleep address (curproc) making it
susceptible to a premature wakeup.
