=============== Troubleshooting =============== Repairing an existing FreeBSD installation ------------------------------------------ FreeBSD releases 2.2.1 and later feature a "Fixit" option in the top menu of the boot floppy. To use it, you will also need either a fixit.flp image floppy, generated in the same fashion as the boot floppy, or the 2nd CDROM from Walnut Creek CDROM's FreeBSD distribution. To invoke fixit, simply boot the boot floppy, chose the "Fixit" item and insert the fixit floppy or CDROM when asked. You will then be placed into a shell with a wide variety of commands available (in the /stand and /mnt2/stand directories) for checking, repairing and examining file systems and their contents. Some UNIX administration experience *is* required to use the fixit option! Known Hardware Problems, Q & A ------------------------------ Q: mcd0 keeps thinking that it has found a device and this stops my Intel EtherExpress card from working. A: Use the UserConfig utility (see HARDWARE.TXT) and disable the probing of the mcd0 and mcd1 devices. Generally speaking, you should only leave the devices that you will be using enabled in your kernel. Q: FreeBSD claims to support the 3Com PCMCIA card, but my card isn't recognized when it's plugged into my laptop. A: There are a couple of possible problems. First of all, FreeBSD does not support multi-function cards, so if you have a combo ethernet/modem card (such as the 3C562), it won't work. The default driver for the 3C589 card was written just like all of the other drivers in FreeBSD, and depend on the card's own configuration data stored in NVRAM to work. You must correctly configure FreeBSD's driver to match the IRQ, port, and IOMEM stored in NVRAM. Unfortunately, the only program capable of reading them is the 3COM supplied DOS program. This program must be run on a absolutely clean system (no other drivers must be running), and the program will whine about CARD-Services not being found, but it will continue. This is necessary to read the NVRAM values. You want to know the IRQ, port, and IOMEM values (the latter is called the CIS tuple by 3COM). The first two can be set in the program, the third is un-settable, and can only be read. Once you have these values, set them in UserConfig and your card will be recognized. Q: FreeBSD finds my PCMCIA network card, but no packets appear to be sent even though it claims to be working. A: Many PCMCIA cards have the ability to use either the 10-Base2 (BNC) or 10-BaseT connectors for connecting to the network. The driver is unable to 'auto-select' the correct connector, so you must tell it which connector to use. In order to switch between the two connectors, the link flags must be set. Depending on the model of the card, '-link0 link1' or 'link0 -link1' will choose the correct network connector. You can set these in sysinstall by using the 'Extra options to ifconfig:' field in the network setup screen. Q: The system finds my ed network card, but I keep getting device timeout errors. A: Your card is probably on a different IRQ from what is specified in the kernel configuration. The ed driver does not use the `soft' configuration by default (values entered using EZSETUP in DOS), but it will use the software configuration if you specify `?' in the IRQ field of your kernel config file. Either move the jumper on the card to a hard configuration setting (altering the kernel settings if necessary), or specify the IRQ as `-1' in UserConfig or `?' in your kernel config file. This will tell the kernel to use the soft configuration. Another possibility is that your card is at IRQ 9, which is shared by IRQ 2 and frequently a cause of problems (especially when you have a VGA card using IRQ 2! :). You should not use IRQ 2 or 9 if at all possible. Q: I go to boot from the hard disk for the first time after installing FreeBSD, but the Boot Manager prompt just prints `F?' at the boot menu each time but the boot won't go any further. A: The hard disk geometry was set incorrectly in the Partition editor when you installed FreeBSD. Go back into the partition editor and specify the actual geometry of your hard disk. You must reinstall FreeBSD again from the beginning with the correct geometry. If you are failing entirely in figuring out the correct geometry for your machine, here's a tip: Install a small DOS partition at the beginning of the disk and install FreeBSD after that. The install program will see the DOS partition and try to infer the correct geometry from it, which usually works. If you are setting up a truly dedicated FreeBSD server or work- station where you don't care for (future) compatibility with DOS, Linux or another operating system, you've also got the option to use the entire disk (`A' in the partition editor), selecting the non-standard option where FreeBSD occupies the entire disk from the very first to the very last sector. This will leave all geometry considerations aside, but is somewhat limiting unless you're never going to run anything other than FreeBSD on a disk. Q: I have a Matsushita/Panasonic drive but it isn't recognized by the system. A: Make certain that the I/O port that the matcd driver is set to is correct for the host interface card you have. (Some SoundBlaster DOS drivers report a hardware I/O port address for the CD-ROM interface that is 0x10 lower than it really is.) If you are unable to determine the settings for the card by examining the board or documentation, you can use UserConfig to change the 'port' address (I/O port) to -1 and start the system. This setting causes the driver to look at a number of I/O ports that various manufacturers use for their Matsushita/Panasonic/Creative CD-ROM interfaces. Once the driver locates the address, you should run UserConfig again and specify the correct address. Leaving the 'port' parameter set to -1 increases the amount of time that it takes the system to boot, and this could interfere with other devices. The double-speed Matsushita CR-562 and CR-563 are the only drives that are supported. Q: I booted the install floppy on my IBM ThinkPad (tm) laptop, and the keyboard is all messed up. A: Older IBM laptops use a non-standard keyboard controller, so you must tell the console driver (sc0) to go into a special mode which works on the ThinkPads. Change the sc0 'Flags' to 0x10 in UserConfig and it should work fine. (Look in the Input Menu for 'Syscons Console Driver'.) Q: I have a Matsushita/Panasonic CR-522, a Matsushita/Panasonic CR-523 or a TEAC CD55a drive, but it is not recognized even when the correct I/O port is set. A: These CD-ROM drives are currently not supported by FreeBSD. The command sets for these drives are not compatible with the double-speed CR-562 and CR-563 drives. The single-speed CR-522 and CR-523 drives can be identified by their use of a CD-caddy. Q: I'm trying to install from a tape drive but all I get is something like: st0(aha0:1:0) NOT READY csi 40,0,0,0 on the screen. Help! A: There's a limitation in the current sysinstall that the tape MUST be in the drive while sysinstall is started or it won't be detected. Try again with the tape in the drive the whole time. Q: I've installed FreeBSD onto my system, but it hangs when booting from the hard drive with the message: ``Changing root to /dev/sd0a''. A: This problem may occur in a system with a 3com 3c509 Ethernet adaptor. The ep0 device driver appears to be sensitive to probes for other devices that also use address 0x300. Boot your FreeBSD system by power cycling the machine (turn off and on). At the ``Boot:'' prompt specify the ``-c''. This will invoke UserConfig (see Section 1. above). Use the ``disable'' command to disable the device probes for all devices at address 0x300 except the ep0 driver. On exit, your machine should successfully boot FreeBSD. Q: My system hangs during boot, right after the "fd0: [my floppy drive]" line. A: This is not actually a hang, simply a very LONG "wdc0" probe that often takes a long time to complete on certain systems (where there usually _isn't_ a WD controller). Be patient, your system will boot! To eliminate the problem, boot with the -c flag and eliminate the wdc0 device, or compile a custom kernel. Q: My system can not find my Intel EtherExpress 16 card. A: You must set your Intel EtherExpress 16 card to be memory mapped at address 0xD0000, and set the amount of mapped memory to 32K using the Intel supplied softset.exe program. Q: When installing on an EISA HP Netserver, my on-board AIC-7xxx SCSI controller isn't detected. A: This is a known problem, and will hopefully be fixed in the future. In order to get your system installed at all, boot with the -c option into UserConfig, but _don't_ use the pretty visual mode but the plain old CLI mode. Type eisa 12 quit there at the prompt. (Instead of `quit', you might also type `visual', and continue the rest of the configuration session in visual mode.) While it's recommended to compile a custom kernel, dset(8) now also understands to save this value. Refer to the FAQ topic 3.16 for an explanation of the problem, and for how to continue. Remember that you can find the FAQ on your local system in /usr/share/doc/FAQ, provided you have installed the `doc' distribution. Q: I have a Panasonic AL-N1 or Rios Chandler Pentium machine and I find that the system hangs before ever getting into the installation now. A: Your machine doesn't like the new i586_copyout and i586_copyin code for some reason. To disable this, boot the installation boot floppy and when it comes to the very first menu (the choice to drop into kernel UserConfig mode or not) choose the command-line interface ("expert mode") version and type the following at it: flags npx0 1 Then proceed normally to boot. This will be saved into your kernel, so you only need to do it once. Q: I have this CMD640 IDE controller that is said to be broken. A: Yes, it is. There's a workaround available now and it is enabled automatically if this chip is used on your system. For the details refer to the manual page of the disk driver (man 4 wd). Q: On a Compaq Aero notebook, I get the message "No floppy devices found! Please check ..." when trying to install from floppy. A: With Compaq being always a little different from other systems, they do not announce their floppy drive in the CMOS RAM of an Aero notebook. Therefore, the floppy disk driver assumes there is no drive configured. Go to the UserConfig screen, and set the Flags value of the fdc0 device to 0x1. This pretends the existance of the first floppy drive (as a 1.44 MB drive) to the driver without asking the CMOS at all. Q: When I go to boot my Intel AL440LX ("Atlanta") -based system from the hard disk the first time, it stops with a "Read Error" message. A: There appears to be a bug in the BIOS on at least some of these boards, this bug results in the FreeBSD bootloader thinking that it is booting from a floppy disk. This is only a problem if you are not using the BootEasy boot manager. Slice the disk in 'compatible' mode and install BootEasy during the FreeBSD installation to avoid the bug. [ Please add more hardware tips to this Q&A section! ]