441 lines
19 KiB
Plaintext
441 lines
19 KiB
Plaintext
+===================== Installing FreeBSD ==========================+
|
|
| |
|
|
| Table of Contents: |
|
|
| |
|
|
| 0.0 Quick Start: |
|
|
| 0.1 Installing FreeBSD from CDROM or the Internet. |
|
|
| |
|
|
| 1.0 Detail on various installation types: |
|
|
| 1.1 Installing from a network CDROM |
|
|
| 1.2 Installing from Floppies |
|
|
| 1.3 Installing from QIC/SCSI tape |
|
|
| 1.4 Installing over a network using NFS or FTP |
|
|
| 1.4.1 NFS Installation tips |
|
|
| 1.4.2 FTP Installation tips |
|
|
| |
|
|
+=====================================================================+
|
|
|
|
Author: Jordan K. Hubbard
|
|
Last updated: Wed May 12 01:13:56 PDT 1999
|
|
|
|
0.0 Quick Start
|
|
--- -----------
|
|
|
|
This manual documents the process of making a new installation of
|
|
FreeBSD on your machine. If you are upgrading from a previous
|
|
release of FreeBSD, please see the file UPGRADE.TXT for important
|
|
information on upgrading. If you are not familiar with configuring
|
|
PC hardware for FreeBSD, you should also read the HARDWARE.TXT file -
|
|
it contains important information which may save you a lot of grief.
|
|
|
|
If you're new to FreeBSD then you should also read EVERYTHING listed
|
|
in the Documentation menu on the boot floppy. It may seem like a lot
|
|
to read, but the time you spend now reading the documents will be made
|
|
up many times over because you were adequately prepared. Also, you will
|
|
know the types of information available should you get stuck later.
|
|
Once the system is installed, you can also revisit this menu and use a
|
|
WEB browser to read the installed FAQ (Frequently Asked Questions) and
|
|
Handbook HTML documentation sets for FreeBSD. You can also use the
|
|
browser to visit other WEB sites on the net (like http://www.freebsd.org)
|
|
if you have an Internet connection. See ABOUT.TXT for more information
|
|
on the resources available to you.
|
|
|
|
The best laid plans sometimes go awry, so if you run into trouble take a
|
|
look at TROUBLE.TXT which contains valuable troubleshooting information.
|
|
|
|
DISCLAIMER: While FreeBSD does its best to safeguard against
|
|
accidental loss of data, it's still more than possible to WIPE OUT
|
|
YOUR ENTIRE DISK with this installation! Please do not proceed to the
|
|
final FreeBSD installation menu unless you've adequately backed up any
|
|
important data first! We really mean it!
|
|
|
|
FreeBSD/alpha supports the following alpha platforms:
|
|
|
|
UDB, Multia, AXPpci33, Noname
|
|
EB164, PC164, PC164LX, PC164SX
|
|
EB64+, Aspen Alpine, etc.
|
|
AlphaStation 200, 250, 255, 400
|
|
AlphaStation 500, 600
|
|
AlphaServer 1000 (1000A untested)
|
|
Digital Personal Workstation 433, 500, 600
|
|
Compaq Professional Workstation XP900, XP1000, AlphaServer DS10
|
|
AlphaServer DS20 (single CPU only)
|
|
DEC3000/300 family (netboot only)
|
|
DEC3000/[4-9]00 family (netboot only)
|
|
|
|
You will need a dedicated disk for FreeBSD/alpha. It is not possible
|
|
to share a disk with another operating system at this time. This disk
|
|
will need to be attached to a SCSI controller which is supported by
|
|
the SRM firmware (currently NCR or SYMBIOS and Qlogic ISP are supported).
|
|
|
|
You will need the SRM console firmware for your platform. In some
|
|
cases, it is possible to switch between AlphaBIOS (or ARC) firmware
|
|
and SRM. In others it will be necessary to download new firmware from
|
|
|
|
ftp.digital.com/pub/DEC/Alpha/firmware
|
|
|
|
|
|
0.1 Installing FreeBSD from CDROM or the Internet
|
|
--- ---------------------------------------------
|
|
|
|
The easiest type of installation is from CD. If you have a supported
|
|
CDROM drive and a FreeBSD installation CD from Walnut Creek CDROM, you
|
|
can start the installation by building a set of FreeBSD boot floppy
|
|
from the files floppies/kern.flp and floppies/mfsroot.flp using the
|
|
instructions found in floppies/README.TXT. From the SRM console prompt
|
|
(>>>), just insert the kern.flp floppy and type the following command
|
|
to start the installation:
|
|
|
|
>>>boot dva0
|
|
|
|
Insert the mfsroot.flp floppy when prompted and you will end up at the
|
|
first screen of the install program.
|
|
|
|
If you don't have a CDROM and would like to simply install over the
|
|
net using PPP, slip or a dedicated connection, simply fetch the
|
|
<FreeBSD-release>/floppies/kern.flp and mfsroot.flp files from:
|
|
|
|
ftp://ftp.freebsd.org/pub/FreeBSD
|
|
|
|
or one of its many mirrors (http://www.freebsd.org/handbook/mirrors.html)
|
|
and follow step 3 above. You should also read the floppies/README.TXT
|
|
file as it contains important information for downloaders.
|
|
|
|
Once you have a boot floppy made, please go to section 1.4 of this
|
|
document for additional tips on installing via FTP or NFS.
|
|
|
|
|
|
1.0 Detail on various installation types
|
|
--- ------------------------------------
|
|
|
|
Once you've gotten yourself to the initial installation screen
|
|
somehow, you should be able to follow the various menu prompts and go
|
|
from there. If you've never used the FreeBSD installation before, you
|
|
are also encouraged to read some of the documentation in the the
|
|
Documentation submenu as well as the general "Usage" instructions on
|
|
the first menu.
|
|
|
|
REMEMBER: If you get stuck at a screen, hit F1 for the online
|
|
documentation for that section.
|
|
|
|
If you've never installed FreeBSD before, or even if you have, the
|
|
"Novice" installation mode is the most recommended since it makes sure
|
|
that you'll visit all the various important checklist items along the
|
|
way. If you're much more comfortable with the FreeBSD installation
|
|
process and know _exactly_ what you want to do, use the Express or
|
|
Custom installation options. If you're upgrading an existing system,
|
|
use the Upgrade option.
|
|
|
|
The FreeBSD installer supports the direct use of floppy, DOS, tape,
|
|
CDROM, FTP, NFS and UFS partitions as installation media, further tips
|
|
on installing from each type of media listed below.
|
|
|
|
Once the install procedure has finished, you will be able to start
|
|
FreeBSD/alpha by typeing something like this to the SRM prompt:
|
|
|
|
>>>boot dkc0
|
|
|
|
This instructs the firmware to boot the specified disk. To find the
|
|
SRM names of disks in your machine, use the show device command:
|
|
|
|
>>>show device
|
|
dka0.0.0.4.0 DKA0 TOSHIBA CD-ROM XM-57 3476
|
|
dkc0.0.0.1009.0 DKC0 RZ1BB-BS 0658
|
|
dkc100.1.0.1009.0 DKC100 SEAGATE ST34501W 0015
|
|
dva0.0.0.0.1 DVA0
|
|
ewa0.0.0.3.0 EWA0 00-00-F8-75-6D-01
|
|
pkc0.7.0.1009.0 PKC0 SCSI Bus ID 7 5.27
|
|
pqa0.0.0.4.0 PQA0 PCI EIDE
|
|
pqb0.0.1.4.0 PQB0 PCI EIDE
|
|
|
|
|
|
This example is from a Digital Personal Workstation 433au and shows
|
|
three disks attached to the machine. The first is a CDROM called dka0
|
|
and the other two are disks and are called dkc0 and dkc100
|
|
repectively.
|
|
|
|
You can specify which kernel file to load and what boot options to use
|
|
with the -file and -flags options to boot, e.g.:
|
|
|
|
>>>boot -file kernel.old -flags s
|
|
|
|
To make FreeBSD/alpha boot automatically, use these commands:
|
|
|
|
>>>set boot_osflags a
|
|
>>>set bootdef_dev dkc0
|
|
>>>set auto_action BOOT
|
|
|
|
|
|
1.1 Installing from a network CDROM
|
|
--- -------------------------------
|
|
|
|
If you simply wish to install from a local CDROM drive then see the
|
|
Quick Start section. If you don't have a CDROM drive on your system
|
|
and wish to use a FreeBSD distribution CD in the CDROM drive of
|
|
another system to which you have network connectivity, there are
|
|
several ways of going about it:
|
|
|
|
1. If you would be able to FTP install FreeBSD directly from the CDROM
|
|
drive in some FreeBSD machine, it's quite easy: You simply add the
|
|
following line to the password file (using the vipw command):
|
|
|
|
ftp:*:99:99::0:0:FTP:/cdrom:/sbin/nologin
|
|
|
|
And anyone else on your network will now be able to choose a Media type
|
|
of FTP and type in: ``ftp://<machine with CDROM drive>'' after picking
|
|
"Other" in the ftp sites menu.
|
|
|
|
2. If you would rather use NFS to export the CDROM directly to the
|
|
machine(s) you'll be installing from, you need to first add an
|
|
entry to the /etc/exports file (on the machine with the CDROM drive)
|
|
which looks something like this:
|
|
|
|
/cdrom -ro ziggy.foo.com
|
|
|
|
To allow the machine "ziggy.foo.com" to mount the CDROM directly
|
|
via NFS during installation. The machine with the CDROM must also
|
|
be configured as an NFS server, of course, and if you're not sure how
|
|
to do that then an NFS installation is probably not the best choice
|
|
for you unless you're willing to read up on rc.conf(5) and configure
|
|
things appropriately. Assuming that this part goes smoothly, you
|
|
should be able to enter: <cdrom-host>:/cdrom as the path for an NFS
|
|
installation when the target machine is installed.
|
|
|
|
|
|
1.2 Installing from Floppies
|
|
--- ------------------------
|
|
|
|
If you must install from floppy disks, either due to unsupported
|
|
hardware or just because you enjoy doing things the hard way, you must
|
|
first prepare some floppies for the install.
|
|
|
|
First, make a set of boot floppies as described in floppies/README.TXT.
|
|
|
|
Second, read the file LAYOUT.TXT and pay special attention to the
|
|
"Distribution format" section since it describes which files you're
|
|
going to need to put onto floppy and which you can safely skip.
|
|
|
|
Next you will need, at minimum, as many 1.44MB floppies as it takes to
|
|
hold all files in the bin (binary distribution) directory. If you're
|
|
preparing these floppies under DOS, then THESE floppies *must* be
|
|
formatted using the MS-DOS FORMAT command. If you're using Windows,
|
|
use the Windows File Manager format command.
|
|
|
|
Don't trust Factory Preformatted floppies! Format them again
|
|
yourself, just to make sure. Many problems reported by our users in
|
|
the past have resulted from the use of improperly formatted media,
|
|
which is why I'm taking such special care to mention it here!
|
|
|
|
If you're creating the floppies from another FreeBSD machine, a format
|
|
is still not a bad idea though you don't need to put a DOS filesystem
|
|
on each floppy. You can use the `disklabel' and `newfs' commands to
|
|
put a UFS filesystem on a floppy, as the following sequence of
|
|
commands illustrates:
|
|
|
|
fdformat -f 1440 fd0.1440
|
|
disklabel -w -r fd0.1440 floppy3
|
|
newfs -t 2 -u 18 -l 1 -i 65536 /dev/rfd0
|
|
|
|
After you've formatted the floppies for DOS or UFS, you'll need to
|
|
copy the files onto them. The distribution files are split into
|
|
chunks conveniently sized so that 5 of them will fit on a conventional
|
|
1.44MB floppy. Go through all your floppies, packing as many files as
|
|
will fit on each one, until you've got all the distributions you want
|
|
packed up in this fashion. Each distribution should go into its own
|
|
subdirectory on the floppy, e.g.: a:\bin\bin.inf, a:\bin\bin.aa,
|
|
a:\bin\bin.ab, ...
|
|
|
|
IMPORTANT NOTE: The bin.inf file also needs to go on the first floppy
|
|
of the bin set since it is read by the installation program in order
|
|
to figure out how many additional pieces to look for when fetching and
|
|
concatenating the distribution. When putting distributions onto
|
|
floppies, the <distname>.inf file MUST occupy the first floppy of each
|
|
distribution set!
|
|
|
|
Once you come to the Media screen of the install, select "Floppy" and
|
|
you'll be prompted for the rest.
|
|
|
|
|
|
1.3 Installing from QIC/SCSI Tape
|
|
--- -----------------------------
|
|
|
|
When installing from tape, the installation program expects the files
|
|
to be simply tar'ed onto it, so after fetching all of the files for
|
|
the distributions you're interested in, simply tar them onto the tape
|
|
with a command something like this:
|
|
|
|
cd /where/you/have/your/dists
|
|
tar cvf /dev/rwt0 (or /dev/rsa0) dist1 .. dist2
|
|
|
|
When you go to do the installation, you should also make sure that you
|
|
leave enough room in some temporary directory (which you'll be allowed
|
|
to choose) to accommodate the FULL contents of the tape you've
|
|
created. Due to the non-random access nature of tapes, this method of
|
|
installation requires quite a bit of temporary storage! You should
|
|
expect to require as much temporary storage as you have stuff written
|
|
on tape.
|
|
|
|
SPECIAL NOTE: When going to do the installation, the tape must be in
|
|
the drive *before* booting from the boot floppy. The installation
|
|
"probe" may otherwise fail to find it.
|
|
|
|
Now create a boot floppy as described in section 0.1 and proceed with
|
|
the installation.
|
|
|
|
|
|
1.4 Installing over a network using FTP or NFS
|
|
--- ------------------------------------------
|
|
|
|
After making a boot floppy as described in the first section, you can
|
|
load the rest of the installation over a network using one of 3 types
|
|
of connections:
|
|
|
|
Serial port: SLIP / PPP
|
|
Parallel port: PLIP (using ``laplink'' style cable)
|
|
Ethernet: A standard Ethernet controller (including
|
|
certain PCCARD devices).
|
|
|
|
Serial Port
|
|
-----------
|
|
|
|
SLIP support is rather primitive, and is limited primarily to
|
|
hard-wired links, such as a serial cable running between two
|
|
computers. The link must be hard-wired because the SLIP installation
|
|
doesn't currently offer a dialing capability. If you need to dial out
|
|
with a modem or otherwise dialog with the link before connecting to
|
|
it, then I recommend that the PPP utility be used instead.
|
|
|
|
If you're using PPP, make sure that you have your Internet Service
|
|
Provider's IP address and DNS information handy as you'll need to know
|
|
it fairly early in the installation process. You may also need to
|
|
know your own IP address, though PPP supports dynamic address
|
|
negotiation and may be able to pick up this information directly from
|
|
your ISP if they support it.
|
|
|
|
You will also need to know how to use the various "AT commands" for
|
|
dialing out with your particular brand of modem as the PPP dialer
|
|
provides only a very simple terminal emulator.
|
|
|
|
|
|
Parallel Port
|
|
-------------
|
|
|
|
If a hard-wired connection to another FreeBSD or Linux machine is
|
|
available, you might also consider installing over a "laplink"
|
|
style parallel port cable. The data rate over the parallel port
|
|
is much higher than what is typically possible over a serial line
|
|
(up to 50k/sec), thus resulting in a quicker installation. It's not
|
|
typically necessary to use "real" IP addresses when using a
|
|
point-to-point parallel cable in this way and you can generally just
|
|
use RFC 1918 style addresses for the ends of the link (e.g. 10.0.0.1,
|
|
10.0.0.2, etc).
|
|
|
|
IMPORTANT NOTE: If you use a Linux machine rather than a FreeBSD
|
|
machine as your PLIP peer, you will also have to specify "link0" in
|
|
the TCP/IP setup screen's ``extra options for ifconfig'' field.
|
|
|
|
|
|
Ethernet
|
|
--------
|
|
|
|
FreeBSD supports most common PC Ethernet cards, a table of supported
|
|
cards (and their required settings) being provided as part of the
|
|
FreeBSD Hardware Guide (see the Documentation menu on the boot floppy
|
|
or the top level directory of the CDROM). If you are using one of the
|
|
supported PCMCIA Ethernet cards, also be sure that it's plugged in
|
|
BEFORE the laptop is powered on! FreeBSD does not, unfortunately,
|
|
currently support "hot insertion" of PCMCIA cards during installation.
|
|
|
|
You will also need to know your IP address on the network, the
|
|
"netmask" value for your address class and the name of your machine.
|
|
Your system administrator can tell you which values are appropriate to
|
|
your particular network setup. If you will be referring to other
|
|
hosts by name rather than IP address, you'll also need a name server
|
|
and possibly the address of a gateway (if you're using PPP, it's your
|
|
provider's IP address) to use in talking to it.
|
|
|
|
If you do not know the answers to these questions then you should
|
|
really probably talk to your system administrator _first_ before
|
|
trying this type of installation! Using a randomly chosen IP address
|
|
or netmask on a live network will almost certainly get you shot at
|
|
dawn.
|
|
|
|
Once you have a network connection of some sort working, the
|
|
installation can continue over NFS or FTP.
|
|
|
|
|
|
1.4.1 NFS installation tips
|
|
----- ---------------------
|
|
|
|
NFS installation is fairly straight-forward: Simply copy the
|
|
FreeBSD distribution files you want onto a server somewhere
|
|
and then point the NFS media selection at it.
|
|
|
|
If this server supports only "privileged port" access (as is
|
|
generally the default for Sun and Linux workstations), you
|
|
will need to set this option in the Options menu before
|
|
installation can proceed.
|
|
|
|
If you have a poor quality Ethernet card which suffers from very
|
|
slow transfer rates, you may also wish to toggle the appropriate
|
|
Options flag.
|
|
|
|
In order for NFS installation to work, the server must also support
|
|
"subdir mounts", e.g. if your FreeBSD 2.2 distribution directory
|
|
lives on: ziggy:/usr/archive/stuff/FreeBSD
|
|
Then ziggy will have to allow the direct mounting of
|
|
/usr/archive/stuff/FreeBSD, not just /usr or /usr/archive/stuff.
|
|
|
|
In FreeBSD's /etc/exports file this is controlled by the
|
|
``-alldirs'' option. Other NFS servers may have different
|
|
conventions. If you are getting `Permission Denied' messages
|
|
from the server then it's likely that you don't have this
|
|
properly enabled!
|
|
|
|
|
|
1.4.2 FTP Installation tips
|
|
----- ---------------------
|
|
|
|
FTP installation may be done from any mirror site containing a
|
|
reasonably up-to-date version of FreeBSD. A full menu of
|
|
reasonable choices for almost any location in the world is
|
|
provided in the FTP site menu during installation.
|
|
|
|
If you are installing from some other FTP site not listed in
|
|
this menu, or you are having troubles getting your name server
|
|
configured properly, you can also specify your own URL by
|
|
selecting the ``Other'' choice in that menu. A URL can
|
|
contain a hostname or an IP address, so the following would
|
|
work in the absence of a name server:
|
|
|
|
ftp://192.216.191.11/pub/FreeBSD/3.2-RELEASE
|
|
|
|
There are two FTP installation modes you can use:
|
|
|
|
o FTP:
|
|
|
|
For all FTP transfers, use the standard "Active" mode for
|
|
transfers. This will not work through most firewalls but
|
|
will often work best with older ftp servers that do not
|
|
support passive mode. If your connection hangs with
|
|
passive mode, try this one!
|
|
|
|
o FTP Passive:
|
|
|
|
For all FTP transfers, use "Passive" mode. This allows
|
|
the user to pass through firewalls that do not allow
|
|
incoming connections on random port addresses.
|
|
|
|
NOTE: ACTIVE AND PASSIVE MODES ARE NOT THE SAME AS A `PROXY'
|
|
CONNECTIONS, WHERE A PROXY FTP SERVER IS LISTENING ON A
|
|
DIFFERENT PORT!
|
|
|
|
In such instances, you should specify the URL as something like:
|
|
|
|
ftp://foo.bar.com:1234/pub/FreeBSD
|
|
|
|
Where "1234" is the port number of the proxy ftp server.
|
|
|
|
|
|
---- End of Installation Guide ---
|