freebsd-dev/contrib/ntp/html/driver20.htm
1999-12-09 13:01:21 +00:00

132 lines
3.8 KiB
HTML

<HTML>
<HEAD>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<META NAME="GENERATOR" CONTENT="Mozilla/4.01 [en] (Win95; I) [Netscape]">
<TITLE>Generic NMEA GPS Receiver
</TITLE>
</HEAD>
<BODY>
<H3>
Generic NMEA GPS Receiver</H3>
<HR>
<H4>
Synopsis</H4>
Address: 127.127.20.<I>u</I>
<BR>Reference ID: <TT>GPS</TT>
<BR>Driver ID: <TT>GPS_NMEA</TT>
<BR>Serial Port: <TT>/dev/gps<I>u</I></TT>; 4800 baud, 8-bits, no parity
<BR>Features: <TT>tty_clk</TT>
<H4>
Description</H4>
This driver supports GPS receivers with the <TT>$GPRMC</TT> NMEA output string.
The driver expect the receiver to be set up to transmit a <TT>$GPRMC</TT>
message every second.
<P>The accuracy depend on the receiver used. Inexpesive GPS models are
available with a claimed PPS signal accuracy of 1 <FONT FACE="Symbol">m</FONT>s
or better relative to the broadcast signal. However, in most cases the
actual accuracy is limited by the precision of the timecode and the latencies
of the serial interface and operating system.
<P>The $GPRMC message that the GPS transmits look like this:
<PRE>$GPRMC,POS_UTC,POS_STAT,LAT,LAT_REF,LON,LON_REF,SPD,HDG,DATE,MAG_VAR,MAG_REF*CC&lt;cr>&lt;lf>
&nbsp; POS_UTC&nbsp; - UTC of position. Hours, minutes and seconds. (hhmmss)
&nbsp; POS_STAT - Position status. (A = Data valid, V = Data invalid)
&nbsp; LAT&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Latitude (llll.ll)
&nbsp; LAT_REF&nbsp; - Latitude direction. (N = North, S = South)
&nbsp; LON&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Longitude (yyyyy.yy)
&nbsp; LON_REF&nbsp; - Longitude direction (E = East, W = West)
&nbsp; SPD&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Speed over ground. (knots) (x.x)
&nbsp; HDG&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Heading/track made good (degrees True) (x.x)
&nbsp; DATE&nbsp;&nbsp;&nbsp;&nbsp; - Date (ddmmyy)
&nbsp; MAG_VAR&nbsp; - Magnetic variation (degrees) (x.x)
&nbsp; MAG_REF&nbsp; - Magnetic variation (E = East, W = West)
&nbsp; CC&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Checksum (optional)
&nbsp; &lt;cr>&lt;lf> - Sentence terminator.</PRE>
The driver will send a <TT>$PMOTG,RMC,0000*1D&lt;cr>&lt;lf></TT> message
each time a <TT>$GPRMC</TT> string is needed. This is not needed on most
GPS receivers because they automatically send the <TT>$GPRMC</TT> string
every second and will only work on GPS receivers that understand the <TT>$PMOTG</TT>
string. Others will just ignore it.
<H4>
Setting up the Garmin GPS-25XL</H4>
Switch off all output with by sending it the following string.
<PRE>"$PGRMO,,2&lt;cr>&lt;lf>"</PRE>
Now switch only $GPRMC on by sending it the following string.
<PRE>"$PGRMO,GPRMC,1&lt;cr>&lt;lf>"</PRE>
On some systems the PPS signal isn't switched on by default. It can be
switched on by sending the following string.
<PRE>"$PGRMC,,,,,,,,,,,,2&lt;cr>&lt;lf>"</PRE>
<H4>
Monitor Data</H4>
The $GPRMC string that is used is written to the clockstats file.
<H4>
Fudge Factors</H4>
<DL>
<DT>
<TT>time1 <I>time</I></TT></DT>
<DD>
Specifies the time offset calibration factor, in seconds and fraction,
with default 0.0.</DD>
<DT>
<TT>time2 <I>time</I></TT></DT>
<DD>
Not used by this driver.</DD>
<DT>
<TT>stratum <I>number</I></TT></DT>
<DD>
Specifies the driver stratum, in decimal from 0 to 15, with default 0.</DD>
<DT>
<TT>refid <I>string</I></TT></DT>
<DD>
Specifies the driver reference identifier, an ASCII string from one to
four characters, with default <TT>GPS</TT>.</DD>
<DT>
<TT>flag1 0 | 1</TT></DT>
<DD>
Not used by this driver.</DD>
<DT>
<TT>flag2 0 | 1</TT></DT>
<DD>
Not used by this driver.</DD>
<DT>
<TT>flag3 0 | 1</TT></DT>
<DD>
Not used by this driver.</DD>
<DT>
<TT>flag4 0 | 1</TT></DT>
<DD>
Not used by this driver.</DD>
<P>Additional Information
<P><A HREF="refclock.htm">Reference Clock Drivers</A></DL>
<HR>
<ADDRESS>
David L. Mills (mills@udel.edu)</ADDRESS>
</BODY>
</HTML>