freebsd-dev/sys/i386/scsi/bt.c
Jordan K. Hubbard 1130b656e5 Make the long-awaited change from $Id$ to $FreeBSD$
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.

Boy, I'm glad we're not using sup anymore.  This update would have been
insane otherwise.
1997-01-14 07:20:47 +00:00

1582 lines
37 KiB
C

/*
* Written by Julian Elischer (julian@tfs.com)
* for TRW Financial Systems for use under the MACH(2.5) operating system.
*
* TRW Financial Systems, in accordance with their agreement with Carnegie
* Mellon University, makes this software available to CMU to distribute
* or use in any manner that they see fit as long as this message is kept with
* the software. For this reason TFS also grants any other persons or
* organisations permission to use or modify this software.
*
* TFS supplies this software to be publicly redistributed
* on the understanding that TFS is not responsible for the correct
* functioning of this software in any circumstances.
*
* $FreeBSD$
*/
/*
* Bulogic/Bustek 32 bit Addressing Mode SCSI driver.
*
* NOTE: 1. Some bt5xx card can NOT handle 32 bit addressing mode.
* 2. OLD bt445s Revision A,B,C,D(nowired) + any firmware version
* has broken busmaster for handling 32 bit addressing on H/W bus
* side.
*
* 3. Extended probing still needs confirmation from our user base, due
* to several H/W and firmware dependencies. If you have a problem
* with extended probing, please contact 'amurai@spec.co.jp'
*
* amurai@spec.co.jp 94/6/16
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/malloc.h>
#include <sys/buf.h>
#include <sys/kernel.h>
#include <sys/proc.h>
#include <sys/sysctl.h>
#include <machine/clock.h>
#include <machine/stdarg.h>
#include <vm/vm.h>
#include <vm/vm_param.h>
#include <vm/pmap.h>
#include <scsi/scsi_all.h>
#include <scsi/scsiconf.h>
#include <i386/scsi/btreg.h>
struct bt_data *btdata[NBT];
/*
* I/O Port Interface
*/
#define BT_BASE bt->bt_base
#define BT_CTRL_STAT_PORT (BT_BASE + 0x0) /* control & status */
/* ReadOps WriteOps */
#define BT_HRST 0x80 /* Hardware reset */
#define BT_SRST 0x40 /* Software reset */
#define BT_IRST 0x20 /* Interrupt reset */
#define BT_SCRST 0x10 /* SCSI bus reset */
#define BT_STST 0x80 /* Self test in Progress */
#define BT_DIAGF 0x40 /* Diagnostic Failure */
#define BT_INIT 0x20 /* Mbx Init required */
#define BT_IDLE 0x10 /* Host Adapter Idle */
#define BT_CDF 0x08 /* cmd/data out port full */
#define BT_DF 0x04 /* Data in port full */
#define BT_INVDCMD 0x01 /* Invalid command */
#define BT_STAT_MASK \
(BT_STST | BT_DIAGF | BT_INIT | BT_IDLE | BT_CDF | BT_DF | BT_INVDCMD)
#define BT_CMD_DATA_PORT (BT_BASE + 0x1) /* cmds and datas */
/* ReadOps WriteOps */
#define BT_NOP 0x00 /* No operation */
#define BT_MBX_INIT 0x01 /* Mbx initialization */
#define BT_START_SCSI 0x02 /* start scsi command */
#define BT_START_BIOS 0x03 /* start bios command */
#define BT_INQUIRE 0x04 /* Adapter Inquiry */
#define BT_MBO_INTR_EN 0x05 /* Enable MBO available intr */
#define BT_SEL_TIMEOUT_SET 0x06 /* set selection time-out */
#define BT_BUS_ON_TIME_SET 0x07 /* set bus-on time */
#define BT_BUS_OFF_TIME_SET 0x08 /* set bus-off time */
#define BT_SPEED_SET 0x09 /* set transfer speed */
#define BT_DEV_GET 0x0a /* return installed devices */
#define BT_CONF_GET 0x0b /* return configuration data */
#define BT_TARGET_EN 0x0c /* enable target mode */
#define BT_SETUP_GET 0x0d /* return setup data */
#define BT_WRITE_CH2 0x1a /* write channel 2 buffer */
#define BT_READ_CH2 0x1b /* read channel 2 buffer */
#define BT_WRITE_FIFO 0x1c /* write fifo buffer */
#define BT_READ_FIFO 0x1d /* read fifo buffer */
#define BT_ECHO 0x1e /* Echo command data */
#define BT_MBX_INIT_EXTENDED 0x81 /* Mbx initialization */
#define BT_INQUIRE_REV_THIRD 0x84 /* Get FirmWare version #3 */
#define BT_INQUIRE_REV_FOURTH 0x85 /* Get FirmWare version #4 */
#define BT_INQUIRE_EXTENDED 0x8D /* Adapter Setup Inquiry */
/* The following commands appeared at FirmWare 3.31 */
#define BT_ROUND_ROBIN 0x8f /* Enable/Disable round robin */
#define BT_STRICT_ROUND_ROBIN 0x00 /* Parameter for strict mode */
#define BT_AGRES_ROUND_ROBIN 0x01 /* Parameter for back compat */
#define BT_INTR_PORT (BT_BASE + 0x2) /* Intr. stat */
/* ReadOps WriteOps */
#define BT_ANY_INTR 0x80 /* Any interrupt */
#define BT_SCRD 0x08 /* SCSI reset detected */
#define BT_HACC 0x04 /* Command complete */
#define BT_MBOA 0x02 /* MBX out empty */
#define BT_MBIF 0x01 /* MBX in full */
struct bt_cmd_buf {
u_char byte[16];
};
#define CCB_HASH_SHIFT 9 /* only hash on multiples of 512 */
#define CCB_HASH(x) ((((long int)(x))>>CCB_HASH_SHIFT) % CCB_HASH_SIZE)
#define bt_nextmbx( wmb, mbx, mbio ) \
if ( (wmb) == &((mbx)->mbio[BT_MBX_SIZE - 1 ]) ) \
(wmb) = &((mbx)->mbio[0]); \
else \
(wmb)++;
struct bt_boardID {
u_char board_type;
u_char custom_feture;
char firm_revision;
u_char firm_version;
};
struct bt_setup {
u_char sync_neg:1;
u_char parity:1;
u_char :6;
u_char speed;
u_char bus_on;
u_char bus_off;
u_char num_mbx;
u_char mbx[3]; /* for backwards compatibility */
struct {
u_char offset:4;
u_char period:3;
u_char valid:1;
} sync[8];
u_char disc_sts;
};
struct bt_config {
u_char chan;
#define BUSDMA 0x00
#define CHAN0 0x01
#define CHAN5 0x20
#define CHAN6 0x40
#define CHAN7 0x80
u_char intr;
#define INT9 0x01
#define INT10 0x02
#define INT11 0x04
#define INT12 0x08
#define INT14 0x20
#define INT15 0x40
u_char scsi_dev:3; /* XXX What about Wide Controllers? */
u_char :5;
};
/*
* Determine 32bit address/Data firmware functionality from the bus type
* Note: bt742a/747[s|d]/757/946/445s will return 'E'
* bt542b/545s/545d will return 'A'
* 94/05/18 amurai@spec.co.jp
*/
struct bt_ext_info {
u_char bus_type; /* Host adapter bus type */
#define BT_BUS_TYPE_24bit 'A' /* PC/AT 24 bit address bus type */
#define BT_BUS_TYPE_32bit 'E' /* EISA/VLB/PCI 32 bit address type */
#define BT_BUS_TYPE_MCA 'M' /* Micro chanel? */
u_char bios_addr; /* Bios Address-Not used */
u_short max_seg; /* Max segment List */
u_char num_mbx; /* Number of mailbox */
int32_t mbx_base; /* mailbox base address */
struct {
u_char resv1:1; /* ??? */
u_char force:1; /* ON: force sync */
u_char maxsync:1; /* ON: 10MB/s , OFF: 5MB/s */
u_char resv2:2; /* ??? */
u_char sync:1; /* ON: Sync, OFF: async ONLY!! */
u_char resv3:2; /* ??? */
} s;
u_char firmid[3]; /* Firmware ver. & rev. w/o last char */
};
#define BT_GET_BOARD_INFO 0x8b /* Get H/W ID and Revision */
struct bt_board_info {
u_char id[4]; /* i.e bt742a -> '7','4','2','A' */
u_char ver[2]; /* i.e Board Revision 'H' -> 'H', 0x00 */
};
#define BT_GET_SYNC_VALUE 0x8c /* Get Synchronous Value */
struct bt_sync_value {
u_char value[8]; /* Synchrnous value (value * 10 nsec) */
};
#define KVTOPHYS(x) vtophys(x)
#define PAGESIZ 4096
#define INVALIDATE_CACHE {asm volatile( ".byte 0x0F ;.byte 0x08" ); }
/***********debug values *************/
#define BT_SHOWCCBS 0x01
#define BT_SHOWINTS 0x02
#define BT_SHOWCMDS 0x04
#define BT_SHOWMISC 0x08
static int bt_debug = 0;
SYSCTL_INT(_debug, OID_AUTO, bt_debug, CTLFLAG_RW, &bt_debug, 0, "");
static u_int32_t bt_adapter_info __P((int unit));
static struct bt_ccb *
bt_ccb_phys_kv __P((struct bt_data *bt, physaddr ccb_phys));
static int bt_cmd __P((struct bt_data *bt, int icnt, int ocnt, int wait,
u_char *retval, u_char opcode, ...));
static void bt_done __P((struct bt_data *bt, struct bt_ccb *ccb));
static void bt_free_ccb __P((struct bt_data *bt, struct bt_ccb *ccb,
int flags));
static struct bt_ccb *
bt_get_ccb __P((struct bt_data *bt, int flags));
static void bt_inquire_setup_information __P((struct bt_data *bt,
struct bt_ext_info *info));
static void btminphys __P((struct buf *bp));
static int bt_poll __P((struct bt_data *bt, struct scsi_xfer *xs,
struct bt_ccb *ccb));
#ifdef UTEST
static void bt_print_active_ccbs __P((int unit));
static void bt_print_ccb __P((struct bt_ccb *ccb));
#endif
static int32_t bt_scsi_cmd __P((struct scsi_xfer *xs));
static BT_MBO * bt_send_mbo __P((struct bt_data *bt, int flags, int cmd,
struct bt_ccb *ccb));
static timeout_t
bt_timeout;
u_long bt_unit = 0;
static int btprobing = 1;
/*
* XXX
* Do our own re-probe protection until a configuration
* manager can do it for us. This ensures that we don't
* reprobe a card already found by the EISA or PCI probes.
*/
struct bt_found
{
u_long port;
char probed;
};
static struct bt_found found[] =
{
{ 0x330, 0 },
{ 0x334, 0 },
{ 0x230, 0 },
{ 0x234, 0 },
{ 0x130, 0 },
{ 0x134, 0 }
};
static struct scsi_adapter bt_switch =
{
bt_scsi_cmd,
btminphys,
0,
0,
bt_adapter_info,
"bt",
{ 0, 0 }
};
/* the below structure is so we have a default dev struct for out link struct */
static struct scsi_device bt_dev =
{
NULL, /* Use default error handler */
NULL, /* have a queue, served by this */
NULL, /* have no async handler */
NULL, /* Use default 'done' routine */
"bt",
0,
{ 0, 0 }
};
#define BT_RESET_TIMEOUT 1000
/*
* bt_cmd(bt, icnt, ocnt, wait, retval, opcode, ...)
*
* Activate Adapter command
* icnt: number of args (outbound bytes written after opcode)
* ocnt: number of expected returned bytes
* wait: number of seconds to wait for response
* retval: buffer where to place returned bytes
* opcode: opcode BT_NOP, BT_MBX_INIT, BT_START_SCSI ...
* ...: parameters to the command specified by opcode
*
* Performs an adapter command through the ports. Not to be confused with a
* scsi command, which is read in via the dma; one of the adapter commands
* tells it to read in a scsi command.
*/
static int
#ifdef __STDC__
bt_cmd(struct bt_data *bt, int icnt, int ocnt, int wait, u_char *retval,
u_char opcode, ...)
#else
bt_cmd(bt, icnt, ocnt, wait, retval, opcode, va_alist)
struct bt_data *bt;
int icnt, ocnt, wait;
u_char *retval;
u_char opcode;
va_dcl
#endif
{
va_list ap;
u_char data;
u_char oc;
register i;
int sts;
/*
* multiply the wait argument by a big constant
* zero defaults to 1
*/
if (wait)
wait *= 100000;
else
wait = 100000;
/*
* Wait for the adapter to go idle, unless it's one of
* the commands which don't need this
*/
if (opcode != BT_MBX_INIT && opcode != BT_START_SCSI) {
i = 100000; /* 1 sec? */
while (--i) {
sts = inb(BT_CTRL_STAT_PORT);
if (sts & BT_IDLE) {
break;
}
DELAY(10);
}
if (i == 0) {
if(!btprobing)
printf("bt%d: bt_cmd, host not idle(0x%x)\n",
bt->unit, sts);
return (ENXIO);
}
}
/*
* Now that it is idle, if we expect output, preflush the
* queue feeding to us.
*/
if (ocnt) {
while ((inb(BT_CTRL_STAT_PORT)) & BT_DF)
inb(BT_CMD_DATA_PORT);
}
/*
* Output the command and the number of arguments given
* for each byte, first check the port is empty.
*/
va_start(ap, opcode);
/* test icnt >= 0, to include the command in data sent */
for (data = opcode; icnt >= 0; icnt--, data = (u_char)va_arg(ap, int)) {
sts = inb(BT_CTRL_STAT_PORT);
for (i = wait; i; i--) {
sts = inb(BT_CTRL_STAT_PORT);
if (!(sts & BT_CDF))
break;
DELAY(10);
}
if (i == 0) {
if(!btprobing)
printf("bt%d: bt_cmd, cmd/data port full\n",
bt->unit);
outb(BT_CTRL_STAT_PORT, BT_SRST);
return (ENXIO);
}
outb(BT_CMD_DATA_PORT, data);
}
va_end(ap);
/*
* If we expect input, loop that many times, each time,
* looking for the data register to have valid data
*/
while (ocnt--) {
sts = inb(BT_CTRL_STAT_PORT);
for (i = wait; i; i--) {
sts = inb(BT_CTRL_STAT_PORT);
if (sts & BT_DF)
break;
DELAY(10);
}
if (i == 0) {
if(!btprobing)
printf("bt%d: bt_cmd, cmd/data port empty %d\n",
bt->unit, ocnt);
return (ENXIO);
}
oc = inb(BT_CMD_DATA_PORT);
if (retval)
*retval++ = oc;
}
/*
* Wait for the board to report a finised instruction
*/
i = 100000; /* 1 sec? */
while (--i) {
sts = inb(BT_INTR_PORT);
if (sts & BT_HACC) {
break;
}
DELAY(10);
}
if (i == 0) {
if(!btprobing)
printf("bt%d: bt_cmd, host not finished(0x%x)\n",
bt->unit, sts);
return (ENXIO);
}
outb(BT_CTRL_STAT_PORT, BT_IRST);
return (0);
}
struct bt_data *
bt_alloc(unit, iobase)
int unit;
u_long iobase;
{
struct bt_data *bt;
int i;
if (unit >= NBT) {
printf("bt: unit number (%d) too high\n", unit);
return NULL;
}
/*
* Allocate a storage area for us
*/
if (btdata[unit]) {
printf("bt%d: memory already allocated\n", unit);
return NULL;
}
/*
* Ensure that we haven't already been probed
*/
for (i=0; i < sizeof(found)/sizeof(struct bt_found); i++) {
if (found[i].port == iobase) {
if (found[i].probed)
return NULL;
else {
found[i].probed = 1;
break;
}
}
}
bt = malloc(sizeof(struct bt_data), M_DEVBUF, M_NOWAIT);
if (!bt) {
printf("bt%d: cannot malloc!\n", unit);
return NULL;
}
bzero(bt, sizeof(struct bt_data));
btdata[unit] = bt;
bt->unit = unit;
bt->bt_base = iobase;
return(bt);
}
void
bt_free(bt)
struct bt_data *bt;
{
btdata[bt->unit] = NULL;
free(bt, M_DEVBUF);
return;
}
int
bt_attach(bt)
struct bt_data *bt;
{
struct scsibus_data *scbus;
btprobing = 0;
/*
* fill in the prototype scsi_link.
*/
bt->sc_link.adapter_unit = bt->unit;
bt->sc_link.adapter_targ = bt->bt_scsi_dev;
bt->sc_link.adapter_softc = bt;
bt->sc_link.adapter = &bt_switch;
bt->sc_link.device = &bt_dev;
bt->sc_link.flags = bt->bt_bounce ? SDEV_BOUNCE : 0;
/*
* Prepare the scsibus_data area for the upperlevel
* scsi code.
*/
scbus = scsi_alloc_bus();
/* XXX scbus->magtarg should be adjusted for Wide cards */
if(!scbus)
return 0;
scbus->adapter_link = &bt->sc_link;
/*
* ask the adapter what subunits are present
*/
scsi_attachdevs(scbus);
return 1;
}
/*
* Return some information to the caller about the adapter and its
* capabilities.
*/
static u_int32_t
bt_adapter_info(unit)
int unit;
{
return (2); /* 2 outstanding requests at a time per device */
}
/*
* Catch an interrupt from the adaptor
*/
void
bt_intr(arg)
void *arg;
{
BT_MBI *wmbi;
struct bt_mbx *wmbx;
struct bt_ccb *ccb;
unsigned char stat;
int i, wait;
int found = 0;
struct bt_data *bt;
bt = (struct bt_data *)arg;
#ifdef UTEST
printf("bt_intr ");
#endif
/*
* First acknowlege the interrupt, Then if it's
* not telling about a completed operation
* just return.
*/
stat = inb(BT_INTR_PORT);
if((stat & BT_STAT_MASK) == 0) {
/* Shared interrupt */
return;
}
/* Mail Box out empty ? */
if (stat & BT_MBOA) {
printf("bt%d: Available Free mbo post\n", bt->unit);
/* Disable MBO available interrupt */
outb(BT_CMD_DATA_PORT, BT_MBO_INTR_EN);
wait = 100000; /* 1 sec enough? */
for (i = wait; i; i--) {
if (!(inb(BT_CTRL_STAT_PORT) & BT_CDF))
break;
DELAY(10);
}
if (i == 0) {
printf("bt%d: bt_intr, cmd/data port full\n", bt->unit);
outb(BT_CTRL_STAT_PORT, BT_SRST);
return;
}
outb(BT_CMD_DATA_PORT, 0x00); /* Disable */
wakeup((caddr_t)&bt->bt_mbx);
outb(BT_CTRL_STAT_PORT, BT_IRST);
return;
}
if (!(stat & BT_MBIF)) {
outb(BT_CTRL_STAT_PORT, BT_IRST);
return;
}
/*
* If it IS then process the competed operation
*/
wmbx = &bt->bt_mbx;
wmbi = wmbx->tmbi;
AGAIN:
while (wmbi->stat != BT_MBI_FREE) {
ccb = bt_ccb_phys_kv(bt, (wmbi->ccb_addr));
if (!ccb) {
wmbi->stat = BT_MBI_FREE;
printf("bt: BAD CCB ADDR!\n");
continue;
}
found++;
if ((stat = wmbi->stat) != BT_MBI_OK) {
switch (stat) {
case BT_MBI_ABORT:
#ifdef UTEST
if (bt_debug & BT_SHOWMISC)
printf("abort ");
#endif
ccb->host_stat = BT_ABORTED;
break;
case BT_MBI_UNKNOWN:
ccb = (struct bt_ccb *) 0;
#ifdef UTEST
if (bt_debug & BT_SHOWMISC)
printf("unknown ccb for abort");
#endif
break;
case BT_MBI_ERROR:
break;
default:
panic("Impossible mbxi status");
}
#ifdef UTEST
if ((bt_debug & BT_SHOWCMDS) && ccb) {
u_char *cp;
cp = ccb->scsi_cmd;
printf("op=%x %x %x %x %x %x\n",
cp[0], cp[1], cp[2],
cp[3], cp[4], cp[5]);
printf("stat %x for mbi addr = 0x%08x\n"
,wmbi->stat, wmbi);
printf("addr = 0x%x\n", ccb);
}
#endif
}
wmbi->stat = BT_MBI_FREE;
if (ccb) {
untimeout(bt_timeout, (caddr_t)ccb);
bt_done(bt, ccb);
}
/* Set the IN mail Box pointer for next */ bt_nextmbx(wmbi, wmbx, mbi);
}
if (!found) {
for (i = 0; i < BT_MBX_SIZE; i++) {
if (wmbi->stat != BT_MBI_FREE) {
found++;
break;
}
bt_nextmbx(wmbi, wmbx, mbi);
}
if (!found) {
#ifdef DEBUG
printf("bt%d: mbi at 0x%08x should be found, stat=%02x..resync\n",
bt->unit, wmbi, stat);
#endif
} else {
found = 0;
goto AGAIN;
}
}
wmbx->tmbi = wmbi;
outb(BT_CTRL_STAT_PORT, BT_IRST);
}
/*
* A ccb is put onto the free list.
*/
static void
bt_free_ccb(bt, ccb, flags)
struct bt_data *bt;
struct bt_ccb *ccb;
int flags;
{
unsigned int opri;
opri = splbio();
ccb->next = bt->bt_ccb_free;
bt->bt_ccb_free = ccb;
ccb->flags = CCB_FREE;
/*
* If there were none, wake anybody waiting for one to come free,
* starting with queued entries.
*/
if (!ccb->next) {
wakeup((caddr_t)&bt->bt_ccb_free);
}
splx(opri);
}
/*
* Get a free ccb
*
* If there are none, see if we can allocate a new one. If so, put it in
* the hash table too otherwise either return an error or sleep.
*/
static struct bt_ccb *
bt_get_ccb(bt, flags)
struct bt_data *bt;
int flags;
{
unsigned opri;
struct bt_ccb *ccbp;
int hashnum;
opri = splbio();
/*
* If we can and have to, sleep waiting for one to come free
* but only if we can't allocate a new one.
*/
while (!(ccbp = bt->bt_ccb_free)) {
if (bt->numccbs < BT_CCB_MAX) {
if (ccbp = (struct bt_ccb *) malloc(sizeof(struct bt_ccb),
M_TEMP,
M_NOWAIT)) {
bzero(ccbp, sizeof(struct bt_ccb));
bt->numccbs++;
ccbp->flags = CCB_ACTIVE;
/*
* put in the phystokv hash table
* Never gets taken out.
*/
ccbp->hashkey = KVTOPHYS(ccbp);
hashnum = CCB_HASH(ccbp->hashkey);
ccbp->nexthash = bt->ccbhash[hashnum];
bt->ccbhash[hashnum] = ccbp;
} else {
printf("bt%d: Can't malloc CCB\n", bt->unit);
}
goto gottit;
} else {
if (!(flags & SCSI_NOSLEEP)) {
tsleep((caddr_t)&bt->bt_ccb_free, PRIBIO,
"btccb", 0);
continue;
}
break;
}
}
if (ccbp) {
/* Get CCB from from free list */
bt->bt_ccb_free = ccbp->next;
ccbp->flags = CCB_ACTIVE;
}
gottit:
splx(opri);
return (ccbp);
}
/*
* given a physical address, find the ccb that
* it corresponds to:
*/
static struct bt_ccb *
bt_ccb_phys_kv(bt, ccb_phys)
struct bt_data *bt;
physaddr ccb_phys;
{
int hashnum = CCB_HASH(ccb_phys);
struct bt_ccb *ccbp = bt->ccbhash[hashnum];
while (ccbp) {
if (ccbp->hashkey == ccb_phys)
break;
ccbp = ccbp->nexthash;
}
return ccbp;
}
/*
* Get a MBO and then Send it
*/
static BT_MBO *
bt_send_mbo(bt, flags, cmd, ccb)
struct bt_data *bt;
int flags;
int cmd;
struct bt_ccb *ccb;
{
unsigned opri;
BT_MBO *wmbo; /* Mail Box Out pointer */
struct bt_mbx *wmbx; /* Mail Box pointer specified unit */
int i, wait;
wmbx = &bt->bt_mbx;
opri = splbio();
/* Get the Target OUT mail Box pointer and move to Next */
wmbo = wmbx->tmbo;
wmbx->tmbo = (wmbo == &(wmbx->mbo[BT_MBX_SIZE - 1]) ?
&(wmbx->mbo[0]) : wmbo + 1);
/*
* Check the outmail box is free or not.
* Note: Under the normal operation, it shuld NOT happen to wait.
*/
while (wmbo->cmd != BT_MBO_FREE) {
wait = 100000; /* 1 sec enough? */
/* Enable MBO available interrupt */
outb(BT_CMD_DATA_PORT, BT_MBO_INTR_EN);
for (i = wait; i; i--) {
if (!(inb(BT_CTRL_STAT_PORT) & BT_CDF))
break;
DELAY(10);
}
if (i == 0) {
printf("bt%d: bt_send_mbo, cmd/data port full\n", bt->unit);
outb(BT_CTRL_STAT_PORT, BT_SRST);
return ((BT_MBO *) 0);
}
outb(BT_CMD_DATA_PORT, 0x01); /* Enable */
tsleep((caddr_t)wmbx, PRIBIO, "btsend", 0);
/* XXX */ /*can't do this! */
/* May be servicing an int */
}
/* Link CCB to the Mail Box */
wmbo->ccb_addr = KVTOPHYS(ccb);
ccb->mbx = wmbo;
wmbo->cmd = cmd;
/* Send it! */
outb(BT_CMD_DATA_PORT, BT_START_SCSI);
splx(opri);
return (wmbo);
}
/*
* We have a ccb which has been processed by the
* adaptor, now we look to see how the operation
* went. Wake up the owner if waiting
*/
static void
bt_done(bt, ccb)
struct bt_data *bt;
struct bt_ccb *ccb;
{
struct scsi_sense_data *s1, *s2;
struct scsi_xfer *xs = ccb->xfer;
SC_DEBUG(xs->sc_link, SDEV_DB2, ("bt_done\n"));
/*
* Otherwise, put the results of the operation
* into the xfer and call whoever started it
*/
if ((ccb->host_stat != BT_OK || ccb->target_stat != SCSI_OK)
&& (!(xs->flags & SCSI_ERR_OK))) {
s1 = &(ccb->scsi_sense);
s2 = &(xs->sense);
if (ccb->host_stat) {
switch (ccb->host_stat) {
case BT_ABORTED: /* No response */
SC_DEBUG(xs->sc_link, SDEV_DB3,
("timeout reported back\n"));
xs->error = XS_TIMEOUT;
break;
case BT_SEL_TIMEOUT:
SC_DEBUG(xs->sc_link, SDEV_DB3,
("selection timeout reported back\n"));
xs->error = XS_SELTIMEOUT;
break;
default: /* Other scsi protocol messes */
xs->error = XS_DRIVER_STUFFUP;
SC_DEBUG(xs->sc_link, SDEV_DB3,
("unexpected host_stat: %x\n",
ccb->host_stat));
}
} else {
switch (ccb->target_stat) {
case 0x02:
*s2 = *s1;
xs->error = XS_SENSE;
break;
case 0x08:
xs->error = XS_BUSY;
break;
default:
SC_DEBUG(xs->sc_link, SDEV_DB3,
("unexpected target_stat: %x\n",
ccb->target_stat));
xs->error = XS_DRIVER_STUFFUP;
}
}
} else { /* All went correctly OR errors expected */
xs->resid = 0;
}
xs->flags |= ITSDONE;
bt_free_ccb(bt, ccb, xs->flags);
scsi_done(xs);
}
/*
* Start the board, ready for normal operation
*/
int
bt_init(bt)
struct bt_data* bt;
{
unsigned char ad[4];
volatile int i, sts;
struct bt_config conf;
struct bt_ext_info info;
struct bt_board_info binfo;
/*
* reset board, If it doesn't respond, assume
* that it's not there.. good for the probe
*/
outb(BT_CTRL_STAT_PORT, BT_HRST | BT_SRST);
DELAY(10000);
for (i = BT_RESET_TIMEOUT; i; i--) {
sts = inb(BT_CTRL_STAT_PORT);
if (sts == (BT_IDLE | BT_INIT))
break;
DELAY(1000);
}
if (i == 0) {
#ifdef UTEST
printf("bt_init: No answer from board\n");
#endif
return (ENXIO);
}
DELAY(10000);
/*
* Displaying Board ID and Hardware Revision
* 94/05/18 amurai@spec.co.jp
*/
i = bt_cmd(bt, 1, sizeof(binfo),0,
(u_char *)&binfo,BT_GET_BOARD_INFO,sizeof(binfo));
if(i)
return i;
printf("bt%d: Bt%c%c%c%c/%c%d-", bt->unit,
binfo.id[0],
binfo.id[1],
binfo.id[2],
binfo.id[3],
binfo.ver[0],
(unsigned) binfo.ver[1]
);
/*
* Make sure board has a capability of 32bit addressing.
* and Firmware also need a capability of 32bit addressing pointer
* in Extended mailbox and ccb structure.
* 94/05/18 amurai@spec.co.jp
*/
bt_cmd(bt, 1, sizeof(info),0, (u_char *)&info, BT_INQUIRE_EXTENDED,
sizeof(info));
switch (info.bus_type) {
case BT_BUS_TYPE_24bit: /* PC/AT 24 bit address bus */
printf("ISA(24bit) bus\n");
break;
case BT_BUS_TYPE_32bit: /* EISA/VLB/PCI 32 bit bus */
printf("(32bit) bus\n");
break;
case BT_BUS_TYPE_MCA: /* forget it right now */
printf("MCA bus architecture...");
printf("giving up\n");
return (ENXIO);
break;
default:
printf("Unknown state...");
printf("giving up\n");
return (ENXIO);
break;
}
if ( binfo.id[0] == '4' && binfo.id[1] == '4' && binfo.id[2] == '5' &&
binfo.id[3] == 'S' ) {
printf("bt%d: Your card cannot DMA above 16MB boundary. Bounce buffering enabled.\n", bt->unit);
bt->bt_bounce++;
} else if ( binfo.id[0] == '5' ) {
printf("bt%d: This driver is designed for using 32 bit addressing\n"
"bt%d: mode firmware and EISA/PCI/VLB bus architectures\n"
"bt%d: Bounce-buffering will be used (and is necessary)\n"
"bt%d: if you have more than 16MBytes memory.\n",
bt->unit,
bt->unit,
bt->unit,
bt->unit);
bt->bt_bounce++;
} else if ( info.bus_type == BT_BUS_TYPE_24bit ) {
printf("bt%d: Your board should report a 32bit bus architecture type..\n"
"bt%d: The firmware on your board may have a problem with over\n"
"bt%d: 16MBytes memory handling with this driver.\n",
bt->unit,
bt->unit,
bt->unit);
bt->bt_bounce++;
}
/*
* Assume we have a board at this stage
* setup dma channel from jumpers and save int
* level
*/
printf("bt%d: reading board settings, ", bt->unit);
bt_cmd(bt, 0, sizeof(conf), 0, (u_char *)&conf, BT_CONF_GET);
switch (conf.chan) {
case BUSDMA:
bt->bt_dma = -1;
break;
case CHAN0:
outb(0x0b, 0x0c);
outb(0x0a, 0x00);
bt->bt_dma = 0;
break;
case CHAN5:
outb(0xd6, 0xc1);
outb(0xd4, 0x01);
bt->bt_dma = 5;
break;
case CHAN6:
outb(0xd6, 0xc2);
outb(0xd4, 0x02);
bt->bt_dma = 6;
break;
case CHAN7:
outb(0xd6, 0xc3);
outb(0xd4, 0x03);
bt->bt_dma = 7;
break;
default:
printf("illegal dma setting %x\n", conf.chan);
return (EIO);
}
if (bt->bt_dma == -1)
printf("busmastering, ");
else
printf("dma=%d, ", bt->bt_dma);
switch (conf.intr) {
case INT9:
bt->bt_int = 9;
break;
case INT10:
bt->bt_int = 10;
break;
case INT11:
bt->bt_int = 11;
break;
case INT12:
bt->bt_int = 12;
break;
case INT14:
bt->bt_int = 14;
break;
case INT15:
bt->bt_int = 15;
break;
default:
printf("illegal int setting\n");
return (EIO);
}
printf("int=%d\n", bt->bt_int);
/* who are we on the scsi bus */
bt->bt_scsi_dev = conf.scsi_dev;
/*
* Initialize mail box
*/
*((physaddr *) ad) = KVTOPHYS(&bt->bt_mbx);
bt_cmd(bt, 5, 0, 0, 0, BT_MBX_INIT_EXTENDED
,BT_MBX_SIZE
,ad[0]
,ad[1]
,ad[2]
,ad[3]);
/*
* Set Pointer chain null for just in case
* Link the ccb's into a free-list W/O mbox
* Initialize mail box status to free
*/
if (bt->bt_ccb_free != (struct bt_ccb *) 0) {
printf("bt%d: bt_ccb_free is NOT initialized but init here\n",
bt->unit);
bt->bt_ccb_free = (struct bt_ccb *) 0;
}
for (i = 0; i < BT_MBX_SIZE; i++) {
bt->bt_mbx.mbo[i].cmd = BT_MBO_FREE;
bt->bt_mbx.mbi[i].stat = BT_MBI_FREE;
}
/*
* Set up initial mail box for round-robin operation.
*/
bt->bt_mbx.tmbo = &bt->bt_mbx.mbo[0];
bt->bt_mbx.tmbi = &bt->bt_mbx.mbi[0];
bt_inquire_setup_information(bt, &info);
/*
* Note that we are going and return (to probe)
*/
return 0;
}
static void
bt_inquire_setup_information(bt, info)
struct bt_data* bt;
struct bt_ext_info *info;
{
struct bt_setup setup;
struct bt_sync_value sync;
char dummy[8];
char sub_ver[3];
struct bt_boardID bID;
int i;
/* Inquire Installed Devices */
bzero( &dummy[0], sizeof(dummy) );
bt_cmd(bt, 0, sizeof(dummy), 100, &dummy[0], BT_DEV_GET);
/*
* If board has a capbility of Syncrhonouse mode,
* Get a SCSI Synchronous value
*/
if (info->s.force) { /* Assume fast sync capability */
info->s.sync = 1; /* It's appear at 4.25? version */
info->s.maxsync = 1;
}
if ( info->s.sync ) {
bt_cmd(bt, 1, sizeof(sync), 100,
(u_char *)&sync,BT_GET_SYNC_VALUE,sizeof(sync));
}
/*
* Inquire Board ID to board for firmware version
*/
bt_cmd(bt, 0, sizeof(bID), 0, (u_char *)&bID, BT_INQUIRE);
bt_cmd(bt, 0, 1, 0, &sub_ver[0], BT_INQUIRE_REV_THIRD );
i = ((int)(bID.firm_revision-'0')) * 10 + (int)(bID.firm_version-'0');
if ( i >= 33 ) {
bt_cmd(bt, 0, 1, 0, &sub_ver[1], BT_INQUIRE_REV_FOURTH );
} else {
/*
* Below rev 3.3 firmware has a problem for issuing
* the BT_INQUIRE_REV_FOURTH command.
*/
sub_ver[1]='\0';
}
sub_ver[2]='\0';
if (sub_ver[1]==' ')
sub_ver[1]='\0';
printf("bt%d: version %c.%c%s, ",
bt->unit, bID.firm_revision, bID.firm_version, sub_ver );
/*
* Obtain setup information from board.
*/
bt_cmd(bt, 1, sizeof(setup), 0, (u_char *)&setup, BT_SETUP_GET,
sizeof(setup));
if (setup.sync_neg && info->s.sync ) {
if ( info->s.maxsync ) {
printf("fast sync, "); /* Max 10MB/s */
} else {
printf("sync, "); /* Max 5MB/s */
}
} else {
if ( info->s.sync ) {
printf("async, "); /* Never try by board */
} else {
printf("async only, "); /* Doesn't has a capability on board */
}
}
if (setup.parity) {
printf("parity, ");
} else {
printf("no parity, ");
}
printf("%d mbxs, %d ccbs\n", setup.num_mbx, BT_CCB_MAX);
/*
* Displayi SCSI negotiation value by each target.
* amurai@spec.co.jp
*/
for (i = 0; i < 8; i++) {
if (!setup.sync[i].valid )
continue;
if ( (!setup.sync[i].offset && !setup.sync[i].period)
|| !info->s.sync ) {
printf("bt%d: targ %d async\n", bt->unit, i);
} else {
printf("bt%d: targ %d sync rate=%2d.%02dMB/s(%dns), offset=%02d\n",
bt->unit, i,
100 / sync.value[i],
(100 % sync.value[i]) * 100 / sync.value[i],
sync.value[i] * 10,
setup.sync[i].offset );
}
}
/*
* Enable round-robin scheme - appeared at firmware rev. 3.31
* Below rev 3.XX firmware has a problem for issuing
* BT_ROUND_ROBIN command amurai@spec.co.jp
*/
if ( bID.firm_revision >= '3' ) {
printf("bt%d: Using Strict Round robin scheme\n", bt->unit);
bt_cmd(bt, 1, 0, 0, 0, BT_ROUND_ROBIN, BT_STRICT_ROUND_ROBIN);
} else {
printf("bt%d: Not using Strict Round robin scheme\n", bt->unit);
}
}
#ifndef min
#define min(x,y) (x < y ? x : y)
#endif /* min */
static void
btminphys(bp)
struct buf *bp;
{
if (bp->b_bcount > ((BT_NSEG - 1) * PAGESIZ)) {
bp->b_bcount = ((BT_NSEG - 1) * PAGESIZ);
}
}
/*
* start a scsi operation given the command and the data address. Also needs
* the unit, target and lu.
*/
static int32_t
bt_scsi_cmd(xs)
struct scsi_xfer *xs;
{
struct bt_ccb *ccb;
struct bt_scat_gath *sg;
int seg; /* scatter gather seg being worked on */
int thiskv;
physaddr thisphys, nextphys;
int bytes_this_seg, bytes_this_page, datalen, flags;
struct bt_data *bt;
bt = (struct bt_data *)xs->sc_link->adapter_softc;
SC_DEBUG(xs->sc_link, SDEV_DB2, ("bt_scsi_cmd\n"));
/*
* get a ccb (mbox-out) to use. If the transfer
* is from a buf (possibly from interrupt time)
* then we can't allow it to sleep
*/
flags = xs->flags;
if (flags & ITSDONE) {
printf("bt%d: Already done?\n", bt->unit);
xs->flags &= ~ITSDONE;
}
if (!(flags & INUSE)) {
printf("bt%d: Not in use?\n", bt->unit);
xs->flags |= INUSE;
}
if (!(ccb = bt_get_ccb(bt, flags))) {
xs->error = XS_DRIVER_STUFFUP;
return (TRY_AGAIN_LATER);
}
SC_DEBUG(xs->sc_link, SDEV_DB3,
("start ccb(%p)\n", ccb));
/*
* Put all the arguments for the xfer in the ccb
*/
ccb->xfer = xs;
if (flags & SCSI_RESET) {
ccb->opcode = BT_RESET_CCB;
} else {
/* can't use S/G if zero length */
ccb->opcode = (xs->datalen ?
BT_INIT_SCAT_GATH_CCB
: BT_INITIATOR_CCB);
}
ccb->target = xs->sc_link->target;
ccb->data_out = 0;
ccb->data_in = 0;
ccb->lun = xs->sc_link->lun;
ccb->scsi_cmd_length = xs->cmdlen;
ccb->sense_ptr = KVTOPHYS(&(ccb->scsi_sense));
ccb->req_sense_length = sizeof(ccb->scsi_sense);
if ((xs->datalen) && (!(flags & SCSI_RESET))) { /* can use S/G only if not zero length */
ccb->data_addr = KVTOPHYS(ccb->scat_gath);
sg = ccb->scat_gath;
seg = 0;
#ifdef TFS
if (flags & SCSI_DATA_UIO) {
struct iovec *iovp;
iovp = ((struct uio *) xs->data)->uio_iov;
datalen = ((struct uio *) xs->data)->uio_iovcnt;
xs->datalen = 0;
while ((datalen) && (seg < BT_NSEG)) {
sg->seg_addr = (physaddr) iovp->iov_base;
xs->datalen += sg->seg_len = iovp->iov_len;
SC_DEBUGN(xs->sc_link, SDEV_DB4, ("(0x%x@0x%x)"
,iovp->iov_len, iovp->iov_base));
sg++;
iovp++;
seg++;
datalen--;
}
} else
#endif /* TFS */
{
/*
* Set up the scatter gather block
*/
SC_DEBUG(xs->sc_link, SDEV_DB4,
("%ld @%p:- ", xs->datalen, xs->data));
datalen = xs->datalen;
thiskv = (int) xs->data;
thisphys = KVTOPHYS(thiskv);
while ((datalen) && (seg < BT_NSEG)) {
bytes_this_seg = 0;
/* put in the base address */
sg->seg_addr = thisphys;
SC_DEBUGN(xs->sc_link, SDEV_DB4,
("0x%lx", thisphys));
/* do it at least once */
nextphys = thisphys;
while ((datalen) && (thisphys == nextphys))
/*
* This page is contiguous (physically) with
* the the last, just extend the length
*/
{
/* how far to the end of the page */
nextphys = (thisphys & (~(PAGESIZ - 1)))
+ PAGESIZ;
bytes_this_page = nextphys - thisphys;
/**** or the data ****/
bytes_this_page = min(bytes_this_page
,datalen);
bytes_this_seg += bytes_this_page;
datalen -= bytes_this_page;
/* get more ready for the next page */
thiskv = (thiskv & (~(PAGESIZ - 1)))
+ PAGESIZ;
if (datalen)
thisphys = KVTOPHYS(thiskv);
}
/*
* next page isn't contiguous, finish the seg
*/
SC_DEBUGN(xs->sc_link, SDEV_DB4,
("(0x%x)", bytes_this_seg));
sg->seg_len = bytes_this_seg;
sg++;
seg++;
}
}
/* end of iov/kv decision */
ccb->data_length = seg * sizeof(struct bt_scat_gath);
SC_DEBUGN(xs->sc_link, SDEV_DB4, ("\n"));
if (datalen) {
/*
* there's still data, must have run out of segs!
*/
printf("bt%d: bt_scsi_cmd, more than %d DMA segs\n",
bt->unit, BT_NSEG);
xs->error = XS_DRIVER_STUFFUP;
bt_free_ccb(bt, ccb, flags);
return (HAD_ERROR);
}
} else { /* No data xfer, use non S/G values */
ccb->data_addr = (physaddr) 0;
ccb->data_length = 0;
}
ccb->link_id = 0;
ccb->link_addr = (physaddr) 0;
/*
* Put the scsi command in the ccb and start it
*/
if (!(flags & SCSI_RESET)) {
bcopy(xs->cmd, ccb->scsi_cmd, ccb->scsi_cmd_length);
}
if (bt_send_mbo(bt, flags, BT_MBO_START, ccb) == (BT_MBO *) 0) {
xs->error = XS_DRIVER_STUFFUP;
bt_free_ccb(bt, ccb, flags);
return (TRY_AGAIN_LATER);
}
/*
* Usually return SUCCESSFULLY QUEUED
*/
SC_DEBUG(xs->sc_link, SDEV_DB3, ("cmd_sent\n"));
if (!(flags & SCSI_NOMASK)) {
timeout(bt_timeout, (caddr_t)ccb, (xs->timeout * hz) / 1000);
return (SUCCESSFULLY_QUEUED);
}
/*
* If we can't use interrupts, poll on completion
*/
return (bt_poll(bt, xs, ccb));
}
/*
* Poll a particular unit, looking for a particular xs
*/
static int
bt_poll(bt, xs, ccb)
struct bt_data* bt;
struct scsi_xfer *xs;
struct bt_ccb *ccb;
{
int count = xs->timeout;
u_char stat;
/* timeouts are in msec, so we loop in 1000 usec cycles */
while (count) {
/*
* If we had interrupts enabled, would we
* have got an interrupt?
*/
stat = inb(BT_INTR_PORT);
if (stat & BT_ANY_INTR) {
bt_intr((void *)bt);
}
if (xs->flags & ITSDONE) {
break;
}
DELAY(1000); /* only happens in boot so ok */
count--;
}
if (count == 0) {
/*
* We timed out, so call the timeout handler manually,
* accounting for the fact that the clock is not running yet
* by taking out the clock queue entry it makes.
*/
bt_timeout(ccb);
/*
* because we are polling, take out the timeout entry
* bt_timeout made
*/
untimeout(bt_timeout, (caddr_t)ccb);
count = 2000;
while (count) {
/*
* Once again, wait for the int bit
*/
stat = inb(BT_INTR_PORT);
if (stat & BT_ANY_INTR) {
bt_intr((void *)bt);
}
if (xs->flags & ITSDONE) {
break;
}
DELAY(1000); /* only happens in boot so ok */
count--;
}
if (count == 0) {
/*
* We timed out again... This is bad. Notice that
* this time there is no clock queue entry to remove.
*/
bt_timeout(ccb);
}
}
if (xs->error)
return (HAD_ERROR);
return (COMPLETE);
}
static void
bt_timeout(void *arg1)
{
struct bt_ccb * ccb = (struct bt_ccb *)arg1;
int unit;
struct bt_data *bt;
int s = splbio();
/*
* A timeout routine in kernel DONOT unlink
* Entry chains when time outed....So infinity Loop..
* 94/04/20 amurai@spec.co.jp
*/
untimeout(bt_timeout, (caddr_t)ccb);
unit = ccb->xfer->sc_link->adapter_unit;
bt = btdata[unit];
#ifdef UTEST
bt_print_active_ccbs(bt);
#endif
/*
* If the ccb's mbx is not free, then the board has gone Far East?
*/
if (bt_ccb_phys_kv(bt, ccb->mbx->ccb_addr) == ccb &&
ccb->mbx->cmd != BT_MBO_FREE) {
printf("bt%d: not taking commands!\n", unit);
Debugger("bt742a");
}
/*
* If it has been through before, then
* a previous abort has failed, don't
* try abort again
*/
if (ccb->flags == CCB_ABORTED) {
/*
* abort timed out
*/
printf("bt%d: Abort Operation has timed out\n", unit);
ccb->xfer->retries = 0; /* I MEAN IT ! */
ccb->host_stat = BT_ABORTED;
bt_done(bt, ccb);
} else {
/* abort the operation that has timed out */
printf("bt%d: Try to abort\n", unit);
bt_send_mbo(bt, ~SCSI_NOMASK, BT_MBO_ABORT, ccb);
/* 2 secs for the abort */
ccb->flags = CCB_ABORTED;
timeout(bt_timeout, (caddr_t)ccb, 2 * hz);
}
splx(s);
}
#ifdef UTEST
static void
bt_print_ccb(ccb)
struct bt_ccb *ccb;
{
printf("ccb:%x op:%x cmdlen:%d senlen:%d\n"
,ccb
,ccb->opcode
,ccb->scsi_cmd_length
,ccb->req_sense_length);
printf(" datlen:%d hstat:%x tstat:%x flags:%x\n"
,ccb->data_length
,ccb->host_stat
,ccb->target_stat
,ccb->flags);
}
static void
bt_print_active_ccbs(bt)
struct bt_data *bt;
{
struct bt_ccb *ccb;
int i = 0;
while (i < CCB_HASH_SIZE) {
ccb = bt->ccbhash[i];
while (ccb) {
if (ccb->flags != CCB_FREE)
bt_print_ccb(ccb);
ccb = ccb->nexthash;
}
i++;
}
}
#endif /*UTEST */