freebsd-dev/sys/arm/conf/PANDABOARD.hints
Oleksandr Tymoshenko e53470fee3 Merging of projects/armv6, part 10
- Support for Texas Instruments SoCs:
	- AM335x
	- OMAP4

- Kernel configs, DTS for Beaglebone and Pandaboard

Submitted by:	Ben Gray, Damjan Marion
2012-08-15 06:31:32 +00:00

62 lines
2.1 KiB
Plaintext

# $FreeBSD$
# USB ECHI
#
# TI OMAP Power Management and System Companion Device sitting on the I2C bus
# hint.tps65950.0.at="iicbus0"
# hint.tps65950.0.addr=0xd0
#
# Defines the GPIO pin used to detect the Write Protect stat of the MMC/SD card.
#hint.omap_mmc.0.wp_gpio="23"
#
# If 'phy_reset" is set, then the accompaning PHY is reset using one of the
# GPIO pins. If the reset GPIO pin is not -1 then the pin will be toggled when
# the USB driver is loaded.
hint.ehci.0.phy_reset="0"
#
# Sets the PHY mode for the individual ports, the following values are allowed
# - EHCI_HCD_OMAP3_MODE_UNKNOWN 0
# - EHCI_HCD_OMAP3_MODE_PHY 1
# - EHCI_HCD_OMAP3_MODE_TLL 2
hint.ehci.0.phy_mode_0="1"
hint.ehci.0.phy_mode_1="0"
hint.ehci.0.phy_mode_2="0"
#
# If specified the value indicates a pin that is toggled as a heart-beat. The
# heart beat pusle is triggered every 500ms using the system tick timer.
hint.omap_clk.0.heartbeat_gpio="150"
#
# Padconf (pinmux) settings - typically this would be set by the boot-loader
# but can be overridden here. These hints are applied to the H/W when the
# SCM module is initialised.
#
# The format is:
# hint.omap_scm.0.padconf.<padname>=<muxmode:options>
#
# Where the options can be one of the following:
# output, input, input_pullup, input_pulldown
#
# Setup the pin settings for the HS USB Host (PHY mode)
hint.omap4.0.padconf.ag19="usbb1_ulpiphy_stp:output"
hint.omap4.0.padconf.ae18="usbb1_ulpiphy_clk:input_pulldown"
hint.omap4.0.padconf.af19="usbb1_ulpiphy_dir:input_pulldown"
hint.omap4.0.padconf.ae19="usbb1_ulpiphy_nxt:input_pulldown"
hint.omap4.0.padconf.af18="usbb1_ulpiphy_dat0:input_pulldown"
hint.omap4.0.padconf.ag18="usbb1_ulpiphy_dat1:input_pulldown"
hint.omap4.0.padconf.ae17="usbb1_ulpiphy_dat2:input_pulldown"
hint.omap4.0.padconf.af17="usbb1_ulpiphy_dat3:input_pulldown"
hint.omap4.0.padconf.ah17="usbb1_ulpiphy_dat4:input_pulldown"
hint.omap4.0.padconf.ae16="usbb1_ulpiphy_dat5:input_pulldown"
hint.omap4.0.padconf.af16="usbb1_ulpiphy_dat6:input_pulldown"
hint.omap4.0.padconf.ag16="usbb1_ulpiphy_dat7:input_pulldown"