freebsd-dev/sys/dev/atkbdc/atkbdcreg.h
Marius Strobl 520b635320 - Hook up the new locations of the atkbdc(4), atkbd(4) and psm(4) source
files after they were repo-copied to sys/dev/atkbdc. The sources of
  atkbdc(4) and its children were moved to the new location in preparation
  for adding an EBus front-end to atkbdc(4) for use on sparc64; i.e. in
  order to not further scatter them over the whole tree which would have
  been the result of adding atkbdc_ebus.c in e.g. sys/sparc64/ebus. Another
  reason for the repo-copies was that some of the sources were misfiled,
  e.g. sys/isa/atkbd_isa.c wasn't ISA-specific at all but for hanging
  atkbd(4) off of atkbdc(4) and was renamed to atkbd_atkbdc.c accordingly.
  Most of sys/isa/psm.c, i.e. expect for its PSMC PNP part, also isn't
  ISA-specific.
- Separate the parts of atkbdc_isa.c which aren't actually ISA-specific
  but are shareable between different atkbdc(4) bus front-ends into
  atkbdc_subr.c (repo-copied from atkbdc_isa.c). While here use
  bus_generic_rl_alloc_resource() and bus_generic_rl_release_resource()
  respectively in atkbdc_isa.c instead of rolling own versions.
- Add sparc64 MD bits to atkbdc(4) and atkbd(4) and an EBus front-end for
  atkbdc(4). PS/2 controllers and input devices are used on a couple of
  Sun OEM boards and occur on either the EBus or the ISA bus. Depending on
  the board it's either the only on-board mean to connect a keyboard and
  mouse or an alternative to either RS232 or USB devices.
- Wrap the PSMC PNP part of psm.c in #ifdef DEV_ISA so it can be compiled
  without isa(4) (e.g. for EBus-only machines). This ISA-specific part
  isn't separated into its own source file, yet, as it requires more work
  than was feasible for 6.0 in order to do it in a clean way. Actually
  philip@ is working on a rewrite of psm(4) so a more comprehensive
  clean-up and separation of hardware dependent and independent parts is
  expected to happen after 6.0.

Tested on:	i386, sparc64 (AX1105, AXe and AXi boards)
Reviewed by:	philip
2005-06-10 20:56:38 +00:00

265 lines
7.9 KiB
C

/*-
* Copyright (c) 1996-1999
* Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote
* products derived from this software without specific prior written
* permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
* from kbdio.h,v 1.8 1998/09/25 11:55:46 yokota Exp
*/
#ifndef _DEV_ATKBDC_ATKBDCREG_H_
#define _DEV_ATKBDC_ATKBDCREG_H_
#include "opt_kbd.h" /* Structures depend on the value if KBDIO_DEBUG */
/* constants */
/* I/O ports */
#define KBD_STATUS_PORT 4 /* status port, read */
#define KBD_COMMAND_PORT 4 /* controller command port, write */
#define KBD_DATA_PORT 0 /* data port, read/write
* also used as keyboard command
* and mouse command port
*/
/* controller commands (sent to KBD_COMMAND_PORT) */
#define KBDC_SET_COMMAND_BYTE 0x0060
#define KBDC_GET_COMMAND_BYTE 0x0020
#define KBDC_WRITE_TO_AUX 0x00d4
#define KBDC_DISABLE_AUX_PORT 0x00a7
#define KBDC_ENABLE_AUX_PORT 0x00a8
#define KBDC_TEST_AUX_PORT 0x00a9
#define KBDC_DIAGNOSE 0x00aa
#define KBDC_TEST_KBD_PORT 0x00ab
#define KBDC_DISABLE_KBD_PORT 0x00ad
#define KBDC_ENABLE_KBD_PORT 0x00ae
/* controller command byte (set by KBDC_SET_COMMAND_BYTE) */
#define KBD_TRANSLATION 0x0040
#define KBD_RESERVED_BITS 0x0004
#define KBD_OVERRIDE_KBD_LOCK 0x0008
#define KBD_ENABLE_KBD_PORT 0x0000
#define KBD_DISABLE_KBD_PORT 0x0010
#define KBD_ENABLE_AUX_PORT 0x0000
#define KBD_DISABLE_AUX_PORT 0x0020
#define KBD_ENABLE_AUX_INT 0x0002
#define KBD_DISABLE_AUX_INT 0x0000
#define KBD_ENABLE_KBD_INT 0x0001
#define KBD_DISABLE_KBD_INT 0x0000
#define KBD_KBD_CONTROL_BITS (KBD_DISABLE_KBD_PORT | KBD_ENABLE_KBD_INT)
#define KBD_AUX_CONTROL_BITS (KBD_DISABLE_AUX_PORT | KBD_ENABLE_AUX_INT)
/* keyboard device commands (sent to KBD_DATA_PORT) */
#define KBDC_RESET_KBD 0x00ff
#define KBDC_ENABLE_KBD 0x00f4
#define KBDC_DISABLE_KBD 0x00f5
#define KBDC_SET_DEFAULTS 0x00f6
#define KBDC_SEND_DEV_ID 0x00f2
#define KBDC_SET_LEDS 0x00ed
#define KBDC_ECHO 0x00ee
#define KBDC_SET_SCANCODE_SET 0x00f0
#define KBDC_SET_TYPEMATIC 0x00f3
/* aux device commands (sent to KBD_DATA_PORT) */
#define PSMC_RESET_DEV 0x00ff
#define PSMC_ENABLE_DEV 0x00f4
#define PSMC_DISABLE_DEV 0x00f5
#define PSMC_SET_DEFAULTS 0x00f6
#define PSMC_SEND_DEV_ID 0x00f2
#define PSMC_SEND_DEV_STATUS 0x00e9
#define PSMC_SEND_DEV_DATA 0x00eb
#define PSMC_SET_SCALING11 0x00e6
#define PSMC_SET_SCALING21 0x00e7
#define PSMC_SET_RESOLUTION 0x00e8
#define PSMC_SET_STREAM_MODE 0x00ea
#define PSMC_SET_REMOTE_MODE 0x00f0
#define PSMC_SET_SAMPLING_RATE 0x00f3
/* PSMC_SET_RESOLUTION argument */
#define PSMD_RES_LOW 0 /* typically 25ppi */
#define PSMD_RES_MEDIUM_LOW 1 /* typically 50ppi */
#define PSMD_RES_MEDIUM_HIGH 2 /* typically 100ppi (default) */
#define PSMD_RES_HIGH 3 /* typically 200ppi */
#define PSMD_MAX_RESOLUTION PSMD_RES_HIGH
/* PSMC_SET_SAMPLING_RATE */
#define PSMD_MAX_RATE 255 /* FIXME: not sure if it's possible */
/* status bits (KBD_STATUS_PORT) */
#define KBDS_BUFFER_FULL 0x0021
#define KBDS_ANY_BUFFER_FULL 0x0001
#define KBDS_KBD_BUFFER_FULL 0x0001
#define KBDS_AUX_BUFFER_FULL 0x0021
#define KBDS_INPUT_BUFFER_FULL 0x0002
/* return code */
#define KBD_ACK 0x00fa
#define KBD_RESEND 0x00fe
#define KBD_RESET_DONE 0x00aa
#define KBD_RESET_FAIL 0x00fc
#define KBD_DIAG_DONE 0x0055
#define KBD_DIAG_FAIL 0x00fd
#define KBD_ECHO 0x00ee
#define PSM_ACK 0x00fa
#define PSM_RESEND 0x00fe
#define PSM_RESET_DONE 0x00aa
#define PSM_RESET_FAIL 0x00fc
/* aux device ID */
#define PSM_MOUSE_ID 0
#define PSM_BALLPOINT_ID 2
#define PSM_INTELLI_ID 3
#define PSM_EXPLORER_ID 4
#define PSM_4DMOUSE_ID 6
#define PSM_4DPLUS_ID 8
#define PSM_4DPLUS_RFSW35_ID 24
#ifdef _KERNEL
#define ATKBDC_DRIVER_NAME "atkbdc"
/*
* driver specific options: the following options may be set by
* `options' statements in the kernel configuration file.
*/
/* retry count */
#ifndef KBD_MAXRETRY
#define KBD_MAXRETRY 3
#endif
/* timing parameters */
#ifndef KBD_RESETDELAY
#define KBD_RESETDELAY 200 /* wait 200msec after kbd/mouse reset */
#endif
#ifndef KBD_MAXWAIT
#define KBD_MAXWAIT 5 /* wait 5 times at most after reset */
#endif
/* I/O recovery time */
#define KBDC_DELAYTIME 20
#define KBDD_DELAYTIME 7
/* debug option */
#ifndef KBDIO_DEBUG
#define KBDIO_DEBUG 0
#endif
/* end of driver specific options */
/* types/structures */
#define KBDQ_BUFSIZE 32
typedef struct _kqueue {
int head;
int tail;
unsigned char q[KBDQ_BUFSIZE];
#if KBDIO_DEBUG >= 2
int call_count;
int qcount;
int max_qcount;
#endif
} kqueue;
struct resource;
typedef struct atkbdc_softc {
struct resource *port0; /* data port */
struct resource *port1; /* status port */
bus_space_tag_t iot;
bus_space_handle_t ioh0;
bus_space_handle_t ioh1;
int command_byte; /* current command byte value */
int command_mask; /* command byte mask bits for kbd/aux devices */
int lock; /* FIXME: XXX not quite a semaphore... */
kqueue kbd; /* keyboard data queue */
kqueue aux; /* auxiliary data queue */
} atkbdc_softc_t;
enum kbdc_device_ivar {
KBDC_IVAR_VENDORID,
KBDC_IVAR_SERIAL,
KBDC_IVAR_LOGICALID,
KBDC_IVAR_COMPATID,
};
typedef caddr_t KBDC;
#define KBDC_RID_KBD 0
#define KBDC_RID_AUX 1
/* function prototypes */
atkbdc_softc_t *atkbdc_get_softc(int unit);
int atkbdc_probe_unit(int unit, struct resource *port0, struct resource *port1);
int atkbdc_attach_unit(int unit, atkbdc_softc_t *sc, struct resource *port0,
struct resource *port1);
int atkbdc_configure(void);
KBDC atkbdc_open(int unit);
int kbdc_lock(KBDC kbdc, int lock);
int kbdc_data_ready(KBDC kbdc);
int write_controller_command(KBDC kbdc,int c);
int write_controller_data(KBDC kbdc,int c);
int write_kbd_command(KBDC kbdc,int c);
int write_aux_command(KBDC kbdc,int c);
int send_kbd_command(KBDC kbdc,int c);
int send_aux_command(KBDC kbdc,int c);
int send_kbd_command_and_data(KBDC kbdc,int c,int d);
int send_aux_command_and_data(KBDC kbdc,int c,int d);
int read_controller_data(KBDC kbdc);
int read_kbd_data(KBDC kbdc);
int read_kbd_data_no_wait(KBDC kbdc);
int read_aux_data(KBDC kbdc);
int read_aux_data_no_wait(KBDC kbdc);
void empty_kbd_buffer(KBDC kbdc, int t);
void empty_aux_buffer(KBDC kbdc, int t);
void empty_both_buffers(KBDC kbdc, int t);
int reset_kbd(KBDC kbdc);
int reset_aux_dev(KBDC kbdc);
int test_controller(KBDC kbdc);
int test_kbd_port(KBDC kbdc);
int test_aux_port(KBDC kbdc);
int kbdc_get_device_mask(KBDC kbdc);
void kbdc_set_device_mask(KBDC kbdc, int mask);
int get_controller_command_byte(KBDC kbdc);
int set_controller_command_byte(KBDC kbdc, int command, int flag);
#endif /* _KERNEL */
#endif /* !_DEV_ATKBDC_ATKBDCREG_H_ */