freebsd-dev/sys/dev/aic7xxx/aic7xxx_93cx6.h
Justin T. Gibbs 72df3c5621 Sync Perforce IDs, add tranceiver state change support, and correct
numerous error recovery buglets.

Many thanks to Tor Egge for his assistance in diagnosing problems with
the error recovery code.

aic7xxx.c:
	Report missed bus free events using their own sequencer interrupt
	code to avoid confusion with other "bad phase" interrupts.

	Remove a delay used in debugging.  This delay could only be hit
	in certain, very extreme, error recovery scenarios.

	Handle transceiver state changes correctly.  You can now
	plug an SE device into a hot-plug LVD bus without hanging
	the controller.

	When stepping through a critical section, panic if we step
	more than a reasonable number of times.

	After a bus reset, disable bus reset interupts until we either
	our first attempt to (re)select another device, or another device
	attemps to select us.  This removes the need to busy wait in
	kernel for the scsi reset line to fall yet still ensures we
	see any reset events that impact the state of either our initiator
	or target roles.  Before this change, we had the potential of
	servicing a "storm" of reset interrupts if the reset line was
	held for a significant amount of time.

	Indicate the current sequencer address whenever we dump the
	card's state.

aic7xxx.reg:
	Transceiver state change register definitions.

	Add the missed bussfree sequencer interrupt code.

	Re-enable the scsi reset interrupt if it has been
	disabled before every attempt to (re)select a device
	and when we have been selected as a target.

	When being (re)selected, check to see if the selection
	dissappeared just after we enabled our bus free interrupt.
	If the bus has gone free again, go back to the idle loop
	and wait for another selection.

	Note two locations where we should change our behavior
	if ATN is still raised.  If ATN is raised during the
	presentation of a command complete or disconnect message,
	we should ignore the message and expect the target to put
	us in msgout phase.  We don't currently do this as it
	requires some code re-arrangement so that critical sections
	can be properly placed around our handling of these two
	events.  Otherwise, we cannot guarantee that the check of
	ATN is atomic relative to our acking of the message in
	byte (the kernel could assert ATN).

	Only set the IDENTIFY_SEEN flag after we have settled
	on the SCB for this transaction.  The kernel looks at
	this flag before assuming that SCB_TAG is valid.  This
	avoids confusion during certain types of error recovery.

	Add a critical section around findSCB.  We cannot allow
	the kernel to remove an entry from the disconnected
	list while we are traversing it.  Ditto for get_free_or_disc_scb.

aic7xxx_freebsd.c:
	Only assume that SCB_TAG is accurate if IDENTIFY_SEEN is
	set in SEQ_FLAGS.

	Fix a typo that caused us to execute some code for the
	non-SCB paging case when paging SCBs.  This only occurred
	during error recovery.
2000-11-10 20:13:41 +00:00

93 lines
3.0 KiB
C

/*
* Interface to the 93C46/56 serial EEPROM that is used to store BIOS
* settings for the aic7xxx based adaptec SCSI controllers. It can
* also be used for 93C26 and 93C06 serial EEPROMS.
*
* Copyright (c) 1994, 1995, 2000 Justin T. Gibbs.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU Public License ("GPL").
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $Id: //depot/src/aic7xxx/aic7xxx_93cx6.h#4 $
*
* $FreeBSD$
*/
#ifndef _AIC7XXX_93CX6_H_
#define _AIC7XXX_93CX6_H_
typedef enum {
C46 = 6,
C56_66 = 8
} seeprom_chip_t;
struct seeprom_descriptor {
struct ahc_softc *sd_ahc;
u_int sd_control_offset;
u_int sd_status_offset;
u_int sd_dataout_offset;
seeprom_chip_t sd_chip;
uint16_t sd_MS;
uint16_t sd_RDY;
uint16_t sd_CS;
uint16_t sd_CK;
uint16_t sd_DO;
uint16_t sd_DI;
};
/*
* This function will read count 16-bit words from the serial EEPROM and
* return their value in buf. The port address of the aic7xxx serial EEPROM
* control register is passed in as offset. The following parameters are
* also passed in:
*
* CS - Chip select
* CK - Clock
* DO - Data out
* DI - Data in
* RDY - SEEPROM ready
* MS - Memory port mode select
*
* A failed read attempt returns 0, and a successful read returns 1.
*/
#define SEEPROM_INB(sd) \
ahc_inb(sd->sd_ahc, sd->sd_control_offset)
#define SEEPROM_OUTB(sd, value) \
do { \
ahc_outb(sd->sd_ahc, sd->sd_control_offset, value); \
ahc_flush_device_writes(sd->sd_ahc); \
} while(0)
#define SEEPROM_STATUS_INB(sd) \
ahc_inb(sd->sd_ahc, sd->sd_status_offset)
#define SEEPROM_DATA_INB(sd) \
ahc_inb(sd->sd_ahc, sd->sd_dataout_offset)
int read_seeprom(struct seeprom_descriptor *sd, uint16_t *buf,
u_int start_addr, u_int count);
int verify_cksum(struct seeprom_config *sc);
#endif /* _AIC7XXX_93CX6_H_ */