freebsd-dev/sys/mips/conf/QCA953X_BASE.hints

81 lines
2.1 KiB
Plaintext

# This file (and the kernel config file accompanying it) are not designed
# to be used by themselves. Instead, users of this file should create a
# kernel # config file which includes this file (which gets the basic hints),
# then override the default options (adding devices as needed) and adding
# hints as needed (for example, the GPIO and LAN PHY.)
# $FreeBSD$
hint.apb.0.at="nexus0"
hint.apb.0.irq=4
# ART calibration data mapping device
hint.ar71xx_caldata.0.at="nexus0"
hint.ar71xx_caldata.0.order=0
# mdiobus on arge0 - required to bring up arge0
hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x19000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0
# mdiobus on arge1 - this is what the internal switch is hooked into.
hint.argemdio.1.at="nexus0"
hint.argemdio.1.maddr=0x1a000000
hint.argemdio.1.msize=0x1000
hint.argemdio.1.order=0
# uart0
hint.uart.0.at="apb0"
# see atheros/uart_cpu_ar71xx.c why +3
hint.uart.0.maddr=0x18020003
hint.uart.0.msize=0x18
hint.uart.0.irq=3
# ehci - on IP3
hint.ehci.0.at="nexus0"
hint.ehci.0.maddr=0x1b000100
hint.ehci.0.msize=0x00ffff00
hint.ehci.0.irq=1
hint.arge.0.at="nexus0"
hint.arge.0.maddr=0x19000000
hint.arge.0.msize=0x1000
hint.arge.0.irq=2
hint.arge.1.at="nexus0"
hint.arge.1.maddr=0x1a000000
hint.arge.1.msize=0x1000
hint.arge.1.irq=3
# XXX The ath device hangs off of the AHB, rather than the Nexus.
hint.ath.0.at="nexus0"
hint.ath.0.maddr=0x18100000
hint.ath.0.msize=0x20000
hint.ath.0.irq=0
hint.ath.0.vendor_id=0x168c
hint.ath.0.device_id=0x003d
# Where the ART is - last 64k in the first 8MB of flash
#hint.ar71xx_caldata.0.map.0.ath_fixup_addr=0x1fff0000
#hint.ar71xx_caldata.0.map.0.ath_fixup_size=16384
# And now tell the ath(4) driver where to look!
#hint.ath.0.eeprom_firmware="ar71xx_caldata.0.map.0.eeprom_firmware"
# SPI flash
hint.spi.0.at="nexus0"
hint.spi.0.maddr=0x1f000000
hint.spi.0.msize=0x10
hint.mx25l.0.at="spibus0"
hint.mx25l.0.cs=0
# Watchdog
hint.ar71xx_wdog.0.at="nexus0"
# The GPIO function and pin mask is configured per-board
hint.gpio.0.at="apb0"
hint.gpio.0.maddr=0x18040000
hint.gpio.0.msize=0x1000
hint.gpio.0.irq=2